Uploaded August 2025 | Updated September 2026, 1 week ago
laptopscreen.com/English
laptopscreen.com/English/model/Lenovo/THINKBOOK~14S-IWL
Lenovo ThinkBook 14s IWL
This is a guide on replacing a screen on a Lenovo ThinkBook 14s IWL.
Turn the laptop off and disconnect the power cord.
Start removing the bezel. Insert a plastic pick between the bezel and the LCD.
Move it along the perimeter. Put the bezel aside.
The screen is held in place with adhesive strips with the loose pads in the upper corners.
Using tweezzers pick up the tab at the top right corner. Roll the adhesive strip up on a
screwdriver. Pull it up to releasing the right side of the screen.
The adhesive strip on the left side of the laptop was fragile and we had to use a hair dryer
to soften the glue. Insert a plastic pick between the screen and the back cover and move
it along the edge. Pull the LCD from the back cover. Place the screen on the keyboard
and remove remaining adhesive strip of glue.
Using plastic pick and fingers peel of a clear tape securing a video connector.
Open the connectors bracket. Disconnect the video cable. Discard the old screen.
Place the new screen on the keyboard. Reconnect the video cable. Close the
connector’s bracket and secure it with clear tape.
CAUTION! It is very important not to force any connectors. Also
make sure not to twist or slant the connector when plugging it in.
Now we can test the new screen. Lift the screen up and lean it against the back cover.
Turn the screen on. The screen is working and we can finish the installation process.
We are going to use a set of adhesive strips to reattach the screen to the back cover.
You can buy a set of adhesive strips on our site: Laptopscreen.com.
Using alcohol and a piece of cloth clean the sides of the screen. Apply adhesive strips.
Peel off protective film. Lift the screen up and apply some pressure. Remove the
protective film. Using tweezers tuck the adhesive pads in so they don’t get in the way
of the bezel.
Replace the bezel. Start from the bottom and go along the perimeter. Make sure
that the bezel is in place at the bottom of the screen.
Turn the laptop on and we are done!
ScreenFix.com - Send your cracked screen laptop to us for repair and it maybe featured on this YouTube channel!
laptopscreen.com/English
laptopscreen.com/English/model/Lenovo/THINKBOOK~14S-IWL
Lenovo ThinkBook 14s IWL
This is a guide on replacing a screen on a Lenovo ThinkBook 14s IWL.
Turn the laptop off and disconnect the power cord.
Start removing the bezel. Insert a plastic pick between the bezel and the LCD.
Move it along the perimeter. Put the bezel aside.
The screen is held in place with adhesive strips with the loose pads in the upper corners.
Using tweezzers pick up the tab at the top right corner. Roll the adhesive strip up on a
screwdriver. Pull it up to releasing the right side of the screen.
The adhesive strip on the left side of the laptop was fragile and we had to use a hair dryer
to soften the glue. Insert a plastic pick between the screen and the back cover and move
it along the edge. Pull the LCD from the back cover. Place the screen on the keyboard
and remove remaining adhesive strip of glue.
Using plastic pick and fingers peel of a clear tape securing a video connector.
Open the connectors bracket. Disconnect the video cable. Discard the old screen.
Place the new screen on the keyboard. Reconnect the video cable. Close the
connector’s bracket and secure it with clear tape.
CAUTION! It is very important not to force any connectors. Also
make sure not to twist or slant the connector when plugging it in.
Now we can test the new screen. Lift the screen up and lean it against the back cover.
Turn the screen on. The screen is working and we can finish the installation process.
We are going to use a set of adhesive strips to reattach the screen to the back cover.
You can buy a set of adhesive strips on our site: Laptopscreen.com.
Using alcohol and a piece of cloth clean the sides of the screen. Apply adhesive strips.
Peel off protective film. Lift the screen up and apply some pressure. Remove the
protective film. Using tweezers tuck the adhesive pads in so they don’t get in the way
of the bezel.
Replace the bezel. Start from the bottom and go along the perimeter. Make sure
that the bezel is in place at the bottom of the screen.
Turn the laptop on and we are done!
ScreenFix.com - Send your cracked screen laptop to us for repair and it maybe featured on this YouTube channel!
