Uploaded November 2026 | Updated November 2026, 4 hours ago
laptopscreen.com/English
laptopscreen.com/English/model/Lenovo/THINKPAD~P14S~20S4~SERIES
Lenovo ThinkPad P14s Gen 2 — Screen Replacement
This is a guide on how to replace the screen on a Lenovo ThinkPad P14s Gen 2.
To begin, shut down the laptop. Press F1 to enter Setup, navigate to Power, then Battery, and select Disable Built-in Battery.
The laptop will shut down safely, isolating the battery until the next startup with the charger connected.
The next step is to remove the bezel.
Insert a plastic pick between the bezel and the back cover. Move it along the right edge, then along the top edge. Release the bezel on the left side.
Insert a plastic pick between the bezel and the LCD screen, along the inner edge. Move it around the perimeter. Separate the bezel along the bottom edge and set it aside.
The screen is held in place by two adhesive strips, with loose pull tabs in the top corners and another near the webcam.
Using tweezers, pick up the loose tab in the top-left corner. Roll it around the tweezers and pull out the adhesive strip.
Pull out the adhesive strip on the right side.
The adhesive strips turned out to be old and fragile, so we were unable to remove them completely.
Use a heat gun to warm up the sides of the screen.
Insert a plastic pick between the LCD screen and the back cover. Move it along the edges.
Pick up the loose tab near the webcam and pull it out.
Place the screen on the keyboard.
Using a plastic pick and your fingers, peel off the clear tape securing the video connector.
Open the connector's bracket and disconnect the video cable.
Discard the old screen.
Place the new screen on the keyboard.
Reconnect the video cable, close the connector's bracket, and secure it with clear tape.
CAUTION: It is very important not to force any connectors. Also, make sure not to twist or tilt the connector when plugging it in.
Now we can test the screen.
Lift it up and lean it against the back cover.
Reconnect the power cord and turn on the laptop.
The screen is working, so we can finish the installation process.
Turn off the laptop.
Place the screen back onto the keyboard.
We are going to use a pair of adhesive strips to attach the screen to the back cover.
We include these strips with every adhesive-mounted screen and also sell them separately on our website, LaptopScreen.com.
Use alcohol and a piece of cloth to clean the sides of the screen.
Apply two adhesive strips and remove the protective film.
Lift the screen and apply some pressure to secure it to the adhesive.
Replace the bezel.
Start at the bottom and work your way around the perimeter, pressing firmly.
Use one hand to support the back cover while pressing along the bottom edge.
Turn the laptop sideways and use a plastic pick to make sure the bezel is snapped into place along the hinge cover.
Turn on the laptop, and we're done!
laptopscreen.com/English
laptopscreen.com/English/model/Lenovo/THINKPAD~P14S~20S4~SERIES
Lenovo ThinkPad P14s Gen 2 — Screen Replacement
This is a guide on how to replace the screen on a Lenovo ThinkPad P14s Gen 2.
To begin, shut down the laptop. Press F1 to enter Setup, navigate to Power, then Battery, and select Disable Built-in Battery.
The laptop will shut down safely, isolating the battery until the next startup with the charger connected.
The next step is to remove the bezel.
Insert a plastic pick between the bezel and the back cover. Move it along the right edge, then along the top edge. Release the bezel on the left side.
Insert a plastic pick between the bezel and the LCD screen, along the inner edge. Move it around the perimeter. Separate the bezel along the bottom edge and set it aside.
The screen is held in place by two adhesive strips, with loose pull tabs in the top corners and another near the webcam.
Using tweezers, pick up the loose tab in the top-left corner. Roll it around the tweezers and pull out the adhesive strip.
Pull out the adhesive strip on the right side.
The adhesive strips turned out to be old and fragile, so we were unable to remove them completely.
Use a heat gun to warm up the sides of the screen.
Insert a plastic pick between the LCD screen and the back cover. Move it along the edges.
Pick up the loose tab near the webcam and pull it out.
Place the screen on the keyboard.
Using a plastic pick and your fingers, peel off the clear tape securing the video connector.
Open the connector's bracket and disconnect the video cable.
Discard the old screen.
Place the new screen on the keyboard.
Reconnect the video cable, close the connector's bracket, and secure it with clear tape.
CAUTION: It is very important not to force any connectors. Also, make sure not to twist or tilt the connector when plugging it in.
Now we can test the screen.
Lift it up and lean it against the back cover.
Reconnect the power cord and turn on the laptop.
The screen is working, so we can finish the installation process.
Turn off the laptop.
Place the screen back onto the keyboard.
We are going to use a pair of adhesive strips to attach the screen to the back cover.
We include these strips with every adhesive-mounted screen and also sell them separately on our website, LaptopScreen.com.
Use alcohol and a piece of cloth to clean the sides of the screen.
Apply two adhesive strips and remove the protective film.
Lift the screen and apply some pressure to secure it to the adhesive.
Replace the bezel.
Start at the bottom and work your way around the perimeter, pressing firmly.
Use one hand to support the back cover while pressing along the bottom edge.
Turn the laptop sideways and use a plastic pick to make sure the bezel is snapped into place along the hinge cover.
Turn on the laptop, and we're done!










