Uploaded May 2025 | Updated September 2026, 2 weeks ago
laptopscreen.com
laptopscreen.com/English/brand/Gigabyte
This is a guide on replacing a screen on Gigabyte Aorus 15P KD laptop.
For the replacement process we will need the following tools and items:
- plastic picks
- a heat gun
- set of adhesive strips
To begin turn the laptop off and disconnect the power cord.
Start removing the bezel. The bezel consists of two parts: wider bottom panel
and narrower part framing the screen on top and on the sides.
Separate the bottom part of the bezel and put it aside.
The upper part of the bezel is a u-shaped plastic gasket with the screen inserted into it.
We are going to remove the bezel together with the screen
The screen is held in place with pieces of adhesive strips. Normally we would be able
to pull out adhesive strips and release the screen. But in our case the adhesive is too old
and fragile. So we have to use a heat gun to soften the glue.
Warm up the right, left and top sides of the back cover. Insert the plastic pick between the screen
and the back cover and move it along the perimeter. Separate the screen and place it on
the keyboard. Cut the remaining pieces of glue.
Peel off the black tape securing the video connector. Stick it to the back cover. We are going
to reuse it later. Disconnect the video cable and remove the screen. Place it on the desk.
Remove the remaining strips of glue. We still have the bezel around the top, left and right
sides of the screen. Release the bezel while removing the pieces of Kapton tape. We are going to use it with the
replacement screen. Discard the old screen.
Take the new screen, remove the protective film and insert it into the bezel. Secure it with pieces of
Kapton tape. Place the screen on the keyboard. Reconnect the video cable. Secure it with
a piece of black tape.
CAUTION! It is very important not to force any connectors. Also
make sure not to twist or slant the connector when plugging it in.
Now we can test the screen. Lift the screen up
and lean it against the back cover. The screen is working and we can finish the installation
process.
Apply new set of adhesive strips on the inner sides of the LCD panel.
Lift the screen up and apply some pressure to catch the glue.
Replace the panel at the bottom of the screen. Apply some pressure.
Reconnect the power cord. Turn the laptop on, and we are done!
laptopscreen.com
laptopscreen.com/English/brand/Gigabyte
This is a guide on replacing a screen on Gigabyte Aorus 15P KD laptop.
For the replacement process we will need the following tools and items:
- plastic picks
- a heat gun
- set of adhesive strips
To begin turn the laptop off and disconnect the power cord.
Start removing the bezel. The bezel consists of two parts: wider bottom panel
and narrower part framing the screen on top and on the sides.
Separate the bottom part of the bezel and put it aside.
The upper part of the bezel is a u-shaped plastic gasket with the screen inserted into it.
We are going to remove the bezel together with the screen
The screen is held in place with pieces of adhesive strips. Normally we would be able
to pull out adhesive strips and release the screen. But in our case the adhesive is too old
and fragile. So we have to use a heat gun to soften the glue.
Warm up the right, left and top sides of the back cover. Insert the plastic pick between the screen
and the back cover and move it along the perimeter. Separate the screen and place it on
the keyboard. Cut the remaining pieces of glue.
Peel off the black tape securing the video connector. Stick it to the back cover. We are going
to reuse it later. Disconnect the video cable and remove the screen. Place it on the desk.
Remove the remaining strips of glue. We still have the bezel around the top, left and right
sides of the screen. Release the bezel while removing the pieces of Kapton tape. We are going to use it with the
replacement screen. Discard the old screen.
Take the new screen, remove the protective film and insert it into the bezel. Secure it with pieces of
Kapton tape. Place the screen on the keyboard. Reconnect the video cable. Secure it with
a piece of black tape.
CAUTION! It is very important not to force any connectors. Also
make sure not to twist or slant the connector when plugging it in.
Now we can test the screen. Lift the screen up
and lean it against the back cover. The screen is working and we can finish the installation
process.
Apply new set of adhesive strips on the inner sides of the LCD panel.
Lift the screen up and apply some pressure to catch the glue.
Replace the panel at the bottom of the screen. Apply some pressure.
Reconnect the power cord. Turn the laptop on, and we are done!
