Uploaded October 2024 | Updated September 2026, 1 hour ago
WIDE OPEN DESIGN WAS FOUNDED ON BRINGING THE BEST QUALITY, EXPERTISE, AND SERVICE IN THE OFF-ROAD VEHICLE INDUSTRY. OUR STAFF HAS EXTENSIVE KNOWLEDGE IN TRAIL RIDING, ULTRA 4 RACING, AND ROCK BOUNCING. WE ARE BUILT AND MEASURED ON RESULTS. WE HAVE BUILT CUSTOM OFFROAD VEHICLES FROM THE ULTIMATE JEEP WRANGER, COMPETITIVE ULTRA 4 CAR, AND THE NOTORIOUS ROCKETSHIP ROCK BOUNCER CHASSIS.
#WIDEOPENDESIGN
WIDE OPEN DESIGN WAS FOUNDED ON BRINGING THE BEST QUALITY, EXPERTISE, AND SERVICE IN THE OFF-ROAD VEHICLE INDUSTRY. OUR STAFF HAS EXTENSIVE KNOWLEDGE IN TRAIL RIDING, ULTRA 4 RACING, AND ROCK BOUNCING. WE ARE BUILT AND MEASURED ON RESULTS. WE HAVE BUILT CUSTOM OFFROAD VEHICLES FROM THE ULTIMATE JEEP WRANGER, COMPETITIVE ULTRA 4 CAR, AND THE NOTORIOUS ROCKETSHIP ROCK BOUNCER CHASSIS.
#WIDEOPENDESIGN
![How to Calculate Spring Rates Without a Scale - Wide Open Design
Trying to figure out the correct spring rates for your buggy or rock crawler? In this video, Adam breaks down a simple method for calculating spring rates at home without:
* corner scales
* suspension software
* complicated geometry math
All you need is:
* your shocks installed
* one pair of springs
* a tape measure
* some simple calculations
We cover:
* spring compression measurements
* supported vehicle weight
* dual-rate spring setups
* crossover adjustment nuts
* ride height calculations
* shock travel setup
* spring stacker charts
Perfect for:
* rock crawlers
* Ultra4 cars
* race bouncers
* Jeeps
* custom tube chassis builds
Formula(s) to get Stacked Spring Rate Chart Number:
1. Spring Length - Compressed Length = X
2. X times Spring Rate = Y
3. Y divided by Inches Collapsed at Ride Height
Spring Rate Charts & Info on WOD : https://wideopendesign.com/blogs/tech-videos/mastering-the-math-how-to-calculate-spring-rates-without-a-scale
Timestamps:
Calculating the correct spring rate for your coilovers is one of the most daunting tasks for any builder, but it doesnt have to be. In this masterclass, the Wide Open Design team reveals a failsafe method to determine your rates without ever needing a set of expensive scales [00:51]. We start by installing a single mock-up spring (usually a 150lb rate) to measure the actual weight the shock is supporting [05:56]. By measuring how much that spring compresses under the vehicles weight [07:17], we can calculate the exact poundage—eliminating the need to worry about complex mounting angles or trailing arm leverage [08:02]. We then show you how to use our Spring Stacker Chart to select the perfect secondary spring to achieve your desired ride height and dual-rate performance [09:00]. Stop guessing and start engineering your suspension for the trail.
#WideOpenDesign #Coilovers #SpringRates #OffRoadSuspension #RockCrawler #Ultra4 #TubeChassis #Radflo #RockBouncer #SuspensionTech
Products:
Radflo Shock & Eibach Spring Packages: https://wideopendesign.com/collections/shocks-springs
https://www.wideopendesign.com
https://www.facebook.com/wideopendesign/
http://www.instagram.com/wideopendesign How to Calculate Spring Rates Without a Scale - Wide Open Design](https://i.ytimg.com/vi/Ls_MvF4crp8/mqdefault.jpg)


![GM Dana 60 Front End Outer Kit: The Complete 6-Bolt Solution - Wide Open Design
In this video, Adam Woodlee walks through:
• proper assembly order
• GM vs Ford spindle differences
• spindle nut preload setup
• brake bracket installation
• wheel hub assembly
• dowel-pin keeper system
Timestamps:
If youre building a Kingpin Dana 60 front axle for a Chevrolet, you know that sourcing all the individual outer components can be a massive headache. In this technical walkthrough, the Wide Open Design team shows you our GM Dana 60 Outer Kit, designed specifically for the Chevy 6-bolt spindle pattern [00:14]. We’ve curated everything you need—from the spindle and wheel hubs to the 3/4-ton brake brackets and rotors—so you dont have to spend hours hunting for compatible parts [00:21]. We demonstrate the correct assembly sequence, showing why the spindle always goes on first for a Chevy build [01:27], followed by the brake bracket and the wheel hub assembly [01:35]. This kit even includes the spindle nuts with a dowl-pin keeper system, ensuring your wheel bearing preload stays exactly where you set it [02:51].
The goal was simple: make Dana 60 front-end assembly easy, reliable, and completely straightforward.
The WOD GM Dana 60 Front End Outer Kit includes:
• GM Dana 60 spindle
• Wheel hub assembly
• Bearings & races
• Brake brackets
• 3/4-ton brake rotors
• Calipers
• Wheel studs
• Spindle nuts
• Dowel-pin locking keeper system
• Necessary hardware
Designed for:
• Chevrolet Kingpin Dana 60 axles
• 6-bolt spindle pattern knuckles
To Find More Information or to Order your GM Dana 60 Front End Outer Kit Go Here:
https://wideopendesign.com/collections/front-end-kits/products/dana-60-front-end-kit
#WideOpenDesign #Dana60 #KingpinDana60 #RockCrawler #OffRoadFabrication #Ultra4 #TrailRig #AxleTech #GMDana60 #OffRoadTech
Follow us on Social Media:
Instagram: @WideOpenDesign
Facebook: http://www.facebook.com/WideOpenDesign/
http://www.wideopendesign.com
Located in Murfreesboro, TN, Wide Open Design is a constant trend setter in the off road industry. We build vehicles that are unique, reliable, and full of attitude. GM Dana 60 Front End Outer Kit: The Complete 6-Bolt Solution - Wide Open Design](https://i.ytimg.com/vi/MC7CJ4AL3UA/mqdefault.jpg)






