Uploaded December 2015 | Updated November 2026, 2 days ago
PVA release film is a parting agent that helps parts separate from a mold. Steve from Fibre Glast explains what PVA is and when and how to use it with wax in your fabrication process.
#PVA #MoldRelease #CompositeFabrication
PVA Release Film 13: fibreglast.com/products/pva-release-film-13
Parting Wax 1016: fibreglast.com/products/parting-wax-1016
All mold releases: fibreglast.com/collections/mold-releases
Mold Making Kit: fibreglast.com/products/mold-making-kit
PVA, along with a parting agent such as our Partall Wax, allows for a quick and easy release of parts from a mold. As a dry film, this PVA is resistant to solvents in a resin system, but is still water soluble. In this video we will discuss when and how to use PVA in your fabrication process.
Some considerations to keep in mind, while using PVA:
While PVA can be brushed on, for best results it should be with a spray gun, 12-18 inches away from the substrate.
You will generally wish to apply three layers, the first, a thin mist, allowing for 10-15 minutes to dry completely. Then apply two heavier flow coats, allowing for a complete dry. (30-45 minutes each)
PVA should NOT be used with resin or substrate that contains, or produces, water during the cure.
One gallon of PVA will cover approximately 400 square feet.
WHAT ELSE YOU'LL LEARN
• PVA is short for polyvinyl alcohol, and it is used most often with wax
• PVA on a composite repair seals it from humidity for a tack-free cure
• Leftover PVA wipes off with a wet rag, and it comes in quart and gallon sizes and a 4 gallon case
Want to know more about Mold Construction? View our white papers in the Learning Center: fibreglast.com/pages/learning-center
Questions or thoughts? Let us know in the comments below.
Watch next: Spray Guns for Gel Coat: youtube.com/watch?v=akrN1cKpT4A
CHAPTERS
0:00 Introduction: PVA Release Film at Fibre Glast
0:14 What PVA Is and Why Molds Need a Parting Agent
0:40 Using PVA With Wax: Layers of Partall Wax First
0:51 Spraying PVA in Layers Until It Dries to a Glossy Film
1:07 Using PVA on Composite Repairs for a Tack-Free Cure
1:30 PVA Is Water Soluble: What Not to Use It With
1:43 Cleanup: Wiping PVA Off With a Wet Rag
1:53 Why Parting Agents Protect Molds and Improve Surface Finish
2:08 PVA Sizes: Quart, Gallon, and 4-Gallon Case
PVA release film is a parting agent that helps parts separate from a mold. Steve from Fibre Glast explains what PVA is and when and how to use it with wax in your fabrication process.
#PVA #MoldRelease #CompositeFabrication
PVA Release Film 13: fibreglast.com/products/pva-release-film-13
Parting Wax 1016: fibreglast.com/products/parting-wax-1016
All mold releases: fibreglast.com/collections/mold-releases
Mold Making Kit: fibreglast.com/products/mold-making-kit
PVA, along with a parting agent such as our Partall Wax, allows for a quick and easy release of parts from a mold. As a dry film, this PVA is resistant to solvents in a resin system, but is still water soluble. In this video we will discuss when and how to use PVA in your fabrication process.
Some considerations to keep in mind, while using PVA:
While PVA can be brushed on, for best results it should be with a spray gun, 12-18 inches away from the substrate.
You will generally wish to apply three layers, the first, a thin mist, allowing for 10-15 minutes to dry completely. Then apply two heavier flow coats, allowing for a complete dry. (30-45 minutes each)
PVA should NOT be used with resin or substrate that contains, or produces, water during the cure.
One gallon of PVA will cover approximately 400 square feet.
WHAT ELSE YOU'LL LEARN
• PVA is short for polyvinyl alcohol, and it is used most often with wax
• PVA on a composite repair seals it from humidity for a tack-free cure
• Leftover PVA wipes off with a wet rag, and it comes in quart and gallon sizes and a 4 gallon case
Want to know more about Mold Construction? View our white papers in the Learning Center: fibreglast.com/pages/learning-center
Questions or thoughts? Let us know in the comments below.
Watch next: Spray Guns for Gel Coat: youtube.com/watch?v=akrN1cKpT4A
CHAPTERS
0:00 Introduction: PVA Release Film at Fibre Glast
0:14 What PVA Is and Why Molds Need a Parting Agent
0:40 Using PVA With Wax: Layers of Partall Wax First
0:51 Spraying PVA in Layers Until It Dries to a Glossy Film
1:07 Using PVA on Composite Repairs for a Tack-Free Cure
1:30 PVA Is Water Soluble: What Not to Use It With
1:43 Cleanup: Wiping PVA Off With a Wet Rag
1:53 Why Parting Agents Protect Molds and Improve Surface Finish
2:08 PVA Sizes: Quart, Gallon, and 4-Gallon Case










