Uploaded February 2018 | Updated November 2026, 28 minutes ago
Subscribe to our channel for the latest training videos, climbing tutorials and more! A cordelette is an excellent tool for a multi pitch climb. It is versatile and useful—it can be used in anchors and in rescues. In this video we use a 7mm cordelette, which is the middle ground between being versatile but not too bulky, that is 20 feet long.
1. Tie the cordelette into a loop by putting the two ends together and using a flat overhand knot, leaving 6-8 inches of tail, and tighten the knot by pulling the rope tight in both directions.
Alternatively, you can use a Flemish Bend, which is very elegant, strong, and relatively low profile but takes a bit longer to tie or untie. Some climbers use a double fisherman, but that tends to be harder to untie and can get fused in place when loaded heavily or frequently, then you won’t have the ability to open up the cordelette if you need to build an anchor from spread-out pieces or use it in a rescue.
2. To package the cordelette up into a tight bundle and make it easier to carry on your harness, loop the cordelette over itself three times (depending on length) and tie it over itself using either an overhand or figure eight knot.
3. Clip the two loops of cordelette together using a carabiner, folding it into a compact bundle.
We hope you found this video helpful.
Please remember, rock climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!
Subscribe to our channel for the latest training videos, climbing tutorials and more! A cordelette is an excellent tool for a multi pitch climb. It is versatile and useful—it can be used in anchors and in rescues. In this video we use a 7mm cordelette, which is the middle ground between being versatile but not too bulky, that is 20 feet long.
1. Tie the cordelette into a loop by putting the two ends together and using a flat overhand knot, leaving 6-8 inches of tail, and tighten the knot by pulling the rope tight in both directions.
Alternatively, you can use a Flemish Bend, which is very elegant, strong, and relatively low profile but takes a bit longer to tie or untie. Some climbers use a double fisherman, but that tends to be harder to untie and can get fused in place when loaded heavily or frequently, then you won’t have the ability to open up the cordelette if you need to build an anchor from spread-out pieces or use it in a rescue.
2. To package the cordelette up into a tight bundle and make it easier to carry on your harness, loop the cordelette over itself three times (depending on length) and tie it over itself using either an overhand or figure eight knot.
3. Clip the two loops of cordelette together using a carabiner, folding it into a compact bundle.
We hope you found this video helpful.
Please remember, rock climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!



![Sport Climbing: 3. Quickdraw Considerations | Climbing Tech Tips
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we review quickdraw considerations for the leader while sport climbing.
- Carry enough draws for the route plus two extra “oh crap” draws AND extras for the anchor if needed. Typically ten to twelve draws are plenty, plus any gear needed to rappel, lower, clean, or top rope the route.
- Usually the smaller quick draw dog bones in the 10 to 15cm range are fine as sport routes don’t tend to wander too much.
- If needed, bring longer draws or shoulder length slings trick tripled to extend bolts. For more info on how to trick trippel your slings, please see our video on “Trad Climbing: Draw Considerations” [hyperlink to video]”
- If possible, use “key lock” carabiners on both the bolt ends and the rope ends of the quickdraw, to avoid snagging and getting hung up. Key lock carabiners feature a notchless nose that is less likely to snag on bolt hangers and gear loops.
- A straight gate carabiner is ideal for the bolt side of the draw, while a bent gate carabiner aids in cleanly clipping the rope end of the draw.
- Align the carabiners on the draw’s “dog bone” – or nylon center – so both gates are facing the same direction. This can help minimize the draw twisting and unclipping from the bolt.
- Using a rubber or plastic carabiner “keeper” on the rope side of the draw makes clipping easier and more efficient. Most modern draws and dogbones come with these rubber keepers.
- Clip your draws to the front gear loops on your harness and try to have them evenly distributed on both sides.
- As mentioned in our “Clipping Considerations” video, when clipping a quickdraw to the bolt, clip so the rope runs over the spine of the carabiner—not the gate—as you climb above it (this means the spines should be on the same side as the direction you will be climbing above the bolt). This helps ensure the rope runs over the spine in the event of a fall, thus minimizing the chances of the rope unclipping from the draw.
- Also mentioned in our “Clipping Considerations” video, be sure you don’t “back clip.” Back clipping happens when the climber clips the rope in “upside-down.” In the event of a fall, the rope can unclip from the quickdraw. Instead, the rope should run in this order: Belayer to rock, through quickdraw, to climber.
To avoid back clipping, remember the rule “The rope runs from the rock to the climber.” You know you are clipping correctly if the rope runs up and out into space versus in, towards the rock.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit https://ClimbingTechTips.com for related comments, additional videos, and community feedback! Sport Climbing: 3. Quickdraw Considerations | Climbing Tech Tips](https://i.ytimg.com/vi/xpdgSD41p7g/mqdefault.jpg)





