Uploaded February 2018 | Updated November 2026, 5 hours ago
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we look at another jumaring technique known as the Texas style (aka frog or double leg style). Texas style jumaring is a useful technique for ascending a free hanging line because it allows the climber to get all their power into the lower jumar, in order to slide the upper jumar.
Below are the steps for setting up a Texas style jumar.
Step 1: Attach the first jumar to the fixed rope by opening the cam, hooking it onto the rope, and closing it.
Step 2: Attach the second jumar to the fixed rope just below the first.
Step 3: Clip the first daisy chain to the upper jumar using a locking carabiner. The key here is to keep the the jumar within a reachable distance, such that when you are fully weighting the rope, and the daisy to the upper jumar is taught, your arm has a slight bend at the elbow.
Step 4: Attach the second daisy chain to the lower jumar also using a locking carabiner. The distance here is not as important and a little longer is okay.
Step 6: Attach both ladders (aiders) to the locking carabiner of the lower jumar.
To begin jumaring Texas style:
Step 1: Slide each jumar up and weight the system to get rope stretch out.
Step 2: Grab onto the lower jumar with your left hand, and pull yourself into the jumar while standing up with both legs.
Step 3: With the lower jumar weighted by both legs, slide the upper jumar up quickly with your right hand.
Step 4: Sit in your harness, allowing your body weight to hang on the upper jumar. With the lower jumar now unweighted, slide it up to meet the upper jumar.
Note: If the lower jumar does not slide easily up the rope, slightly disengage (or “feather”) the trigger on the lower jumar without taking it off the rope, then slide it up.
Remember to tie a backup knot in the rope every 10-15 feet.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we look at another jumaring technique known as the Texas style (aka frog or double leg style). Texas style jumaring is a useful technique for ascending a free hanging line because it allows the climber to get all their power into the lower jumar, in order to slide the upper jumar.
Below are the steps for setting up a Texas style jumar.
Step 1: Attach the first jumar to the fixed rope by opening the cam, hooking it onto the rope, and closing it.
Step 2: Attach the second jumar to the fixed rope just below the first.
Step 3: Clip the first daisy chain to the upper jumar using a locking carabiner. The key here is to keep the the jumar within a reachable distance, such that when you are fully weighting the rope, and the daisy to the upper jumar is taught, your arm has a slight bend at the elbow.
Step 4: Attach the second daisy chain to the lower jumar also using a locking carabiner. The distance here is not as important and a little longer is okay.
Step 6: Attach both ladders (aiders) to the locking carabiner of the lower jumar.
To begin jumaring Texas style:
Step 1: Slide each jumar up and weight the system to get rope stretch out.
Step 2: Grab onto the lower jumar with your left hand, and pull yourself into the jumar while standing up with both legs.
Step 3: With the lower jumar weighted by both legs, slide the upper jumar up quickly with your right hand.
Step 4: Sit in your harness, allowing your body weight to hang on the upper jumar. With the lower jumar now unweighted, slide it up to meet the upper jumar.
Note: If the lower jumar does not slide easily up the rope, slightly disengage (or “feather”) the trigger on the lower jumar without taking it off the rope, then slide it up.
Remember to tie a backup knot in the rope every 10-15 feet.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!


![Sport Climbing: 3. Quickdraw Considerations | Climbing Tech Tips
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we review quickdraw considerations for the leader while sport climbing.
- Carry enough draws for the route plus two extra “oh crap” draws AND extras for the anchor if needed. Typically ten to twelve draws are plenty, plus any gear needed to rappel, lower, clean, or top rope the route.
- Usually the smaller quick draw dog bones in the 10 to 15cm range are fine as sport routes don’t tend to wander too much.
- If needed, bring longer draws or shoulder length slings trick tripled to extend bolts. For more info on how to trick trippel your slings, please see our video on “Trad Climbing: Draw Considerations” [hyperlink to video]”
- If possible, use “key lock” carabiners on both the bolt ends and the rope ends of the quickdraw, to avoid snagging and getting hung up. Key lock carabiners feature a notchless nose that is less likely to snag on bolt hangers and gear loops.
- A straight gate carabiner is ideal for the bolt side of the draw, while a bent gate carabiner aids in cleanly clipping the rope end of the draw.
- Align the carabiners on the draw’s “dog bone” – or nylon center – so both gates are facing the same direction. This can help minimize the draw twisting and unclipping from the bolt.
- Using a rubber or plastic carabiner “keeper” on the rope side of the draw makes clipping easier and more efficient. Most modern draws and dogbones come with these rubber keepers.
- Clip your draws to the front gear loops on your harness and try to have them evenly distributed on both sides.
- As mentioned in our “Clipping Considerations” video, when clipping a quickdraw to the bolt, clip so the rope runs over the spine of the carabiner—not the gate—as you climb above it (this means the spines should be on the same side as the direction you will be climbing above the bolt). This helps ensure the rope runs over the spine in the event of a fall, thus minimizing the chances of the rope unclipping from the draw.
- Also mentioned in our “Clipping Considerations” video, be sure you don’t “back clip.” Back clipping happens when the climber clips the rope in “upside-down.” In the event of a fall, the rope can unclip from the quickdraw. Instead, the rope should run in this order: Belayer to rock, through quickdraw, to climber.
To avoid back clipping, remember the rule “The rope runs from the rock to the climber.” You know you are clipping correctly if the rope runs up and out into space versus in, towards the rock.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit https://ClimbingTechTips.com for related comments, additional videos, and community feedback! Sport Climbing: 3. Quickdraw Considerations | Climbing Tech Tips](https://i.ytimg.com/vi/xpdgSD41p7g/mqdefault.jpg)





