Uploaded February 2018 | Updated November 2026, 16 minutes ago
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we look at ways to assess rock quality for your traditional anchor. Consider two points:
1. Check to make sure the rock itself is solid by patting the rock with your hand. Listen for hollow sounds which might identify a detached block that is not visibly obvious. Avoid placing protection points in any rock that sounds hollow.
2. Visually verify that the crack system you want to build your anchor in is not part of a detached block. Even a larger block, while it may not rip out of place in the event of a fall, could shift, thus changing the size of the crack and causing the cam to fail.
Important note: Cams hold a fall by pushing perpendicular to the long axis. This means you can put as much as double the force of the fall on the rock—which means rock quality is of the utmost importance when using cams.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we look at ways to assess rock quality for your traditional anchor. Consider two points:
1. Check to make sure the rock itself is solid by patting the rock with your hand. Listen for hollow sounds which might identify a detached block that is not visibly obvious. Avoid placing protection points in any rock that sounds hollow.
2. Visually verify that the crack system you want to build your anchor in is not part of a detached block. Even a larger block, while it may not rip out of place in the event of a fall, could shift, thus changing the size of the crack and causing the cam to fail.
Important note: Cams hold a fall by pushing perpendicular to the long axis. This means you can put as much as double the force of the fall on the rock—which means rock quality is of the utmost importance when using cams.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!
![Sport Climbing: 3. Quickdraw Considerations | Climbing Tech Tips
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we review quickdraw considerations for the leader while sport climbing.
- Carry enough draws for the route plus two extra “oh crap” draws AND extras for the anchor if needed. Typically ten to twelve draws are plenty, plus any gear needed to rappel, lower, clean, or top rope the route.
- Usually the smaller quick draw dog bones in the 10 to 15cm range are fine as sport routes don’t tend to wander too much.
- If needed, bring longer draws or shoulder length slings trick tripled to extend bolts. For more info on how to trick trippel your slings, please see our video on “Trad Climbing: Draw Considerations” [hyperlink to video]”
- If possible, use “key lock” carabiners on both the bolt ends and the rope ends of the quickdraw, to avoid snagging and getting hung up. Key lock carabiners feature a notchless nose that is less likely to snag on bolt hangers and gear loops.
- A straight gate carabiner is ideal for the bolt side of the draw, while a bent gate carabiner aids in cleanly clipping the rope end of the draw.
- Align the carabiners on the draw’s “dog bone” – or nylon center – so both gates are facing the same direction. This can help minimize the draw twisting and unclipping from the bolt.
- Using a rubber or plastic carabiner “keeper” on the rope side of the draw makes clipping easier and more efficient. Most modern draws and dogbones come with these rubber keepers.
- Clip your draws to the front gear loops on your harness and try to have them evenly distributed on both sides.
- As mentioned in our “Clipping Considerations” video, when clipping a quickdraw to the bolt, clip so the rope runs over the spine of the carabiner—not the gate—as you climb above it (this means the spines should be on the same side as the direction you will be climbing above the bolt). This helps ensure the rope runs over the spine in the event of a fall, thus minimizing the chances of the rope unclipping from the draw.
- Also mentioned in our “Clipping Considerations” video, be sure you don’t “back clip.” Back clipping happens when the climber clips the rope in “upside-down.” In the event of a fall, the rope can unclip from the quickdraw. Instead, the rope should run in this order: Belayer to rock, through quickdraw, to climber.
To avoid back clipping, remember the rule “The rope runs from the rock to the climber.” You know you are clipping correctly if the rope runs up and out into space versus in, towards the rock.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit https://ClimbingTechTips.com for related comments, additional videos, and community feedback! Sport Climbing: 3. Quickdraw Considerations | Climbing Tech Tips](https://i.ytimg.com/vi/xpdgSD41p7g/mqdefault.jpg)





