Modul Charging AC01 TP4056 Step Up voltage 5V DC other model HW 357 J5019 @ObengwareID

Uploaded February 2021 | Updated September 2026, 1 week ago

TP4056 HW 357 J5019 AC01
DIY Board for step-up voltage, from 5V or range 4,5 to 8V DC
Output from 4,3V to 27V DC.
Good for DIY step-up power voltage
Minimum Discharge internal circiut between 6mAh (real test).

Specification
Input voltage: DC4.5-8V
Output voltage: DC4.3V-27V
Output current: 2A MAX
Charging voltage 4.2V, charging current 1A
Before use and before debugging, the default output is about 9V
Calculating Discharge Current 2A Output Current
Output reference maximum current 5V 1.4A, 9V 0.8A, 12V 0.6A
The static current is about 0.5 mA

TP4056 HW 357 J5019 AC01 may different specification, but the same function for step up or increase voltage power
00:00 Varian board HW-357, AC01, J4019 and diagram connect board
00:37 Test output voltage HW-357, AC01, J4019
01:32 Test power output HW-357 output 5V - 9V
02:51 Charging lithium battery
03:00 Test output 12V low current load for fan
03:35 Test power 5V to 12V, without battery
05:51 Drain internal circuit HW-357, AC01, J4019
06:00 Charger baterai 500mAh
06:10 Sample diagram circuit with HW-357, AC01, J4019 DIY board
06:19 Application step-up battery to 6V DC for Blood pressure check.

LED Indicator
Charge Red, Stand-by Green

Example
Step up battery power 4V to 9V for Multimeter
Step up battery power 4V or 5V USB power to power 6V DC blood pressure unit

Operation:
Before use and before debugging, the default output is about 9V.
Input voltage: 4.5-8V
Output voltage can be continuously adjusted 4.3-27V
(Over 4.3V, below 27V, can output any voltage, reversible clockwise adjustable voltage)
Charging voltage: 4.2V, charging current 1A. Test only 250mAh
Calculating Discharge Current 2A Output Current, test only 1A or lower
Output reference maximum current 5V 1.4A, 9V 0.8A, 12V 0.6A
The static current is about 0.5 mA, test 0,6mA.
There is no overdischarge protection for overcharge protection (2V cut-off boost is possible, but 2V output is still not blocked)
Cut-off boost 2V, depending on the situation, whether to add protective plate
For example, VIN + BAT + terminal of 5V solar panel can output 4.2V to 3.7V 18650 battery charging OUT + terminal output adjustable voltage need to be adjusted.
It can be used for multimeter and recharging lithium battery

Modul Charging AC01 TP4056 Step Up voltage 5V DC other model HW 357 J5019

ESP32 A fatal error occurred Failed to connect to ESP32 Wrong Boot Mode

ESP32 error rst 0x1 power on reset boot 0x13 spi fast flash boot

Samsung washing machine spin slow squealing noise

Save file 4GB or bigger Android TV to microSD or Flash Drive exFAT

Install terminate RJ45 connectors on Cat6 and Cat5 LAN cables

$ESP32 C6 Failed uploading error exit status 2 this chip esp32C6 not esp32 Is your ESP32-C6 failing to upload with Exit Status 2? This guide covers how to update to Espressif v3.0.0, configure 16MB flash settings, and solve detection issues in the Arduino IDE for RainMaker and sensor projects Setting Up ESP32-C6 in Arduino IDE and Troubleshooting Exit Status 2 00:09 ESP32-C6 Wroom v2 00:24 ESPconnect check model ESP32 00:38 Problem ESP32-C6 Failed uploading Exit status 2. 01:02 Update ESP32-C6 board Arduino IDE 02:04 Setup ESP32-C6 board model 03 ESP32c6 flash the Rainmaker program. The ESP32-C6 is a powerful Wi-Fi 6 and Matter-enabled microcontroller. However, because it is a newer chip, you might encounter detection issues or the dreaded Exit Status 2 upload error if your environment isnt configured correctly. Follow this step-by-step guide to update your environment and successfully flash your ESP32-C6 (16MB model). 1. Essential Prerequisites Hardware: ESP32-C6 v2 WROOM with 1 USB-C port. Verification: Before opening the IDE, ensure your USB-C cable is data-capable. Check Windows Device Manager under Ports (COM & LPT) to confirm the board is detected when plugged in. 2. Updating the Board Manager If your board is not detected, it is likely because your ESP32 core is outdated. Version 3.0+ is required for C6 support. Open Arduino IDE. Go to File - Preferences. In the Additional boards manager URLs field, add the official Espressif link: https://espressif.github.io/arduino-esp32/package_esp32_index.json Go to Tools - Board - Boards Manager. Search for ESP32 by Espressif Systems and ensure you update to version 3.0.0 or higher. This version adds support for the C3, C5, C6, H2, P4, S2, and S3. 3. Troubleshooting Exit Status 2 (The Clean Flash) The Exit Status 2 error often occurs due to incorrect board selection or a corrupted previous flash. To fix this: Board Selection: Go to Tools - Board - ESP32 and select ESP32C6 Dev Module. Port Selection: Select the COM port that matches your board name. The Empty Program Test: Open a blank sketch (void setup(){} and void loop(){}). Attempt to upload. If this succeeds, the Exit Status 2 error is resolved, and your communication link is stable. 4. Advanced Configuration for ESP RainMaker & Sensors Once the basic flash is successful, you can proceed to more complex implementations, such as using an AHT10 sensor or the ESP RainMaker ecosystem. Flash Settings for RainMaker: When moving to RainMaker, your upload settings must be precise to accommodate the larger framework: Erase Flash: Set to Enabled (highly recommended for the first RainMaker flash to clear old credentials). Flash Mode: Select the mode compatible with your WROOM model (usually DIO or QIO). Flash Size: Select 16MB to match your hardware. Partition Scheme: Select a RainMaker specific partition. This allocates the necessary space for the NVS (Non-Volatile Storage) used for Wi-Fi provisioning and cloud metadata. 5. Final Implementation After configuring the partitions: Enter your full code (e.g., your AHT10 sensor logic). Click Upload. The ESP32-C6 should now boot correctly, initialize the sensor, and connect to the RainMaker cloud. Tip: If the board still fails to enter Download Mode automatically, hold the BOOT button, press and release RESET, then release BOOT before clicking the upload button in the IDE.$

Windows 11 25H2 24H2 IoT Enterprise Installation has failed No Internet

Membasmi keong kecil sumpil di pot kebun tanpa bahan kimia dengan kulit buah saja

BMP280 AHT10 sensor accurate temperature

Boost WIFI range sIgnal and spees internet with reflector

Fix Samsung Washing Machine small water inlet - clean the filer