Modes in iNav: Whats changed in 3.0 and beyond Mr.D - Falling with style 2021-10-01 | In this video, we'll be revisiting modes in iNav. Some things have changed since my first video on modes. Plus, we'll take a sneak peek at a couple of changes to make life easier, coming in the next version of iNav.This is a general overview of the modes. Covering flight modes (manual, acro, horizon, and angle), navigation modes (RTH, pos hold, cruise, and course hold), and much more...** Contents **00:00 Introduction00:49 An overview in iNav Configurator01:41 Arming modes: Arm and Pre-arm02:03 Flight modes: 02:27 - Manual03:01 - Acro or Rate03:38 - Angle04:27 - Horizon04:35 - PID Tuning settings for Horizon and Angle05:28 Navigation modes:05:41 - Return to Home06:17 - Position Hold or Loiter06:58 - Course Hold and Cruise07:28 Flight Mode Modifiers:07:30 - Altitude Hold08:52 - Heading Hold09:32 - Airmode10:12 Full Autonomy modes: Waypoint Mission and Ground-station Control10:47 Function modes:10:50 - Home Reset11:00 - Auto level11:53 - Auto tune12:07 - Autotrim (and permanently enabled)13:07 - Launch mode14:17 - Loiter Change, FPV Angle Mix, Turn Assist, Surface, Headfree, and Headadj15:16 - Beeper15:39 - OSD settings16:04 - Camstab and Camera Control16:20 - Blackbox16:34 - Failsafe and Killswitch17:01 - LEDs Off17:27 Mode ranges, what they mean and how to set up the ranges18:09 Why don't the ranges always light up blue?18:52 Changes to the ranges in iNav 4.0 (coming approx. November 2021)19:59 Acro indicator in iNav 4.020:32 Hide unused modes (from iNav 3.0.2)20:52 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.** In this video ***** Links ***- Adam G's video showing an auto-launch: youtu.be/x-EFevoeSxA?t=32- iNav Configurator: github.com/iNavFlight/inav-configurator/releases*** Hardware ***- SonicModell AR Wing: bit.ly/MrD_32jhbCY- Matek F405-STD: http://bit.ly/MrD_2kkMis6- Matek F405-WING: http://bit.ly/MrD_2sxgQLT- FrSky Horus X10S Express: bit.ly/MrD_3l7b8K5- FrSky Tandem X20S: bit.ly/MrD_3x6n6JL** Help other RC pilots find this video **If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.** Supporting me and other resources **- There are more tutorials on my web site at https://www.MrD-RC.com.- You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook. - Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.- If you found my video useful, you can become a Patreon at patreon.com/MrD_RC- If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi- I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
Jumper T15 Transmitter: First look and unboxing Mr.D - Falling with style 2024-10-13 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at the new T15 transmitter from Jumper RC. This is a mid size entry level transmitter that has a few nice features. Lets check it out.✈️ Contents ✈️00:00 Introduction00:113 Costs and options00:50 Unboxing01:19 The transmitter case and accessories02:12 How does the transmitter feel?02:52 Transmitter basic layout - switches, buttons, trims, USB, and other stuff05:12 The JR bay and how well do modules fit06:02 Batteries08:00 A quick power up and calibration09:41 Plugging in the USB and the storage space available10:33 A couple more features of note and observations11:43 Initial thoughts on the transmitter13:36 Taking the back off the radio14:52 The back of the case and the ELRS module15:51 Adjusting the gimbals and switching mode17:15 The MCU, haptic motor, and speaker17:48 The real time clock battery18:03 The general quality of the internals19:14 ConclusionFor openness, this transmitter was provided by Banggood for review.Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ Jumper T15 transmitter: bit.ly/MrD_JumperT15✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#JumperT15 #RCTransmitter
How to add custom OSD Elements in INAV Mr.D - Falling with style 2024-08-25 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCA really useful addition to INAV 7 was the ability to add custom OSD elements. Using these, you could pretty much show any data you want on the OSD. There are some limits. The data needs to be accessible or created in the programming tab. But other than that, you can fill your boots.In this video, I show an example of how you can simply get some flight data and show it on the OSD. My example shows how to add altitude in metres and distance from home in kilometres. You may think that those units are already available. Not if your OSD is in a non-metric configuration ;)I also show an example of how to replicate the functionality of the current OSD switch indicators.✈️ Contents ✈️00:00 Introduction01:10 Where are the custom OSD elements?01:26 How do you enable the custom OSD elements?02:42 Where do you set up what is shown on the OSD03:10 Basics on customising the OSD element05:50 How do you get the data to put on the custom OSD element?06:00 Example 1: home distance in km and altitude in m08:45 How this collates to the setup on the OSD page09:02 Were do you find the number to use for icons?11:45 Example 2: custom switch indicators18:39 A note about some current limitations for some values20:03 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 INAV Configurator GitHub: github.com/iNavFlight/inav-configurator✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#INAV #CustomOSD #INAV7
Caddx Walksnail Avatar GT: First look Mr.D - Falling with style 2024-08-04 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at the new Caddx Walksnail Avatar GT VTX. This is Walksnails first VTX aimed at long range.✈️ Contents ✈️00:00 Introduction00:31 Specs and differences to other kits03:29 The MicroSD card setup04:29 Antenna connections05:17 Direct solder pad. Warning, these are not for power in!06:05 Internal ceramic antennas07:25 Installation and camera attachments08:20 Camera and antennas08:43 Wiring diagram09:25 Unboxing10:58 My installation overview12:21 How I installed the VTX13:43 A warning about the MicroSD card plastics14:45 How is this setup for VTX heat?15:57 A brief overview of the build of the AR Pro17:20 Final thoughts, TL;DW, and ConclusionIn the video, I made a mistake. I thought that TCS FPV had made a video about why we shouldn't use mW with digital But, he hasn't. He has some interesting videos on antennas though, so you should check out his channel youtube.com/@tmc-fpvTom also runs the awesome https://walksnail.wiki/ web site. Which has lots of helpful information.Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ Walksnail Avatar GT kit: caddxfpv.com/products/walksnail-avatar-gt-kit✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#Walksnail #LongRange #FPV
INAV Public Service Announcement: Cant arm with plenty of satellites & 7.1.1 no baro issue Mr.D - Falling with style 2024-07-14 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we look at a couple of issue that have come up quite a lot recently.The first issue is not being able to arm. Even with a good satellite lock, with at least 6 3D fixes, and a low HDOP. A rogue parameter setting may be causing you this problem.Next we look at the default parameter setting that caused the release of INAV 7.1.2. This setting would turn off the use of the barometer, when in most cases it should be enabled.TL;DW: The CLI commands areset inav_use_gps_no_baro = offset inav_max_eph_epv = 1000✈️ Contents ✈️00:00 Introduction00:18 Can't arm, even with lots of satellite locks and low HDOP02:29 inav_use_gps_no_baro issue. Check even if on 7.1.2Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
Charger balance extension cable Mr.D - Falling with style 2024-06-23 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCHere is a useful little cable from SpeedyBee. Which makes charging easier. In the days of old. Chargers used to come with long leads. Which meant plugging in the battery was pretty easy. These days, chargers are more minimalistic. The main power and balance ports are flush installed in the charger. It looks nice. But it can be a pain to plug in the battery. Especially when the battery has short balance leads.In the past, we could have used regular balance extensions to make life a bit easier. But, you either had to force the balance lead in to the extension. Or cut down the socket on the extension to allow batteries of different cell counts to fit.SpeedyBee have released some balance lead extensions that allow us to have an easier time. The sockets can accept 2S to 6S packs without any forcing or modification.✈️ Contents ✈️00:00 Introduction00:24 How chargers used to look compared to now00:45 Why are the flush balance ports a problem?01:08 The answer to the problem02:47 Any problems with these leads?03:32 It's not needed for parallel charge boards. But here's why I stopped using them04:08 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ SpeedyBee Balance Extension Cable: bit.ly/MrD_SpeedyBeeBalanceExtension✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
Caddx GOFILM 20 Unboxing and review Mr.D - Falling with style 2024-04-28 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at the new @CADDXFPV GOFILM 20 cinewhoop. What do you get? How does it fly? Is it suitable for beginners? Plus much more.✈️ Contents ✈️00:00 Introduction00:31 Unboxing01:42 - In the box, basic accessories, and manual04:12 - What batteries to get?05:04 - The quad and what's on it08:00 What are the defaults on BetaFlight?09:13 - How to setup the barometer, if its not already working10:34 - Default mode setup11:17 - ELRS receiver target12:32 - Receiver page setup13:35 - Failsafe, and how to see if its working15:15 - Motor setup15:25 - Setting the battery details16:15 7 weeks later...16:56 Checking out the quad after weeks of abuse17:08 Make sure to check the prop bolts are there and tight18:49 Check your moonlight settings before flying19:14 My biggest issue with the GOFILM 2020:19 The update cable20:31 MicroSD card removal20:54 The video antennas23:07 The ELRS antenna23:15 A nice upgrade would be an Ummagrip battery pad23:47 Overview of the settings I've been flying for testing24:27 How does it fly on the stock tune?25:32 Would I recommend the GOFILM 20?25:43 Update on battery sizes26:46 How much does this cost and is it reasonable?28:26 Does it compare to the DJI Avata 2?29:47 Would the GOFILM 20 be suitable for a beginner?30:48 ConclusionBetaFlight CLI for barometer and OSDresource I2C_SCL 2 B10resource I2C_SDA 2 B11set baro_bustype = I2Cset baro_i2c_device = 2set osd_canvas_width = 53set osd_canvas_height = 20Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗⚙️ Caddx GOFILM 20: caddxfpv.com/products/caddxfpv-gofilm-20✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#caddx #caddxfpv #gofilm20
Whats new in INAV 7.0 and 7.1? Find our now! Mr.D - Falling with style 2024-04-07 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video, we check out the latest releases from INAV. Versions 7.0 and 7.1. Which was just released on the 1st of April. So what's new? Lets take a look.✈️ Contents ✈️00:00 Introduction00:35 Where to download the latest version of INAV01:19 How to update to INAV 7.101:58 - CLI Autocomplete now in INAV04:36 Where to find the release notes05:46 What's changed in INAV 7.0 and 7.106:26 - Flexible motor and servo allocation (mixer - resource remapping alternative)09:37 - VTOL in INAV (tilt rotor, quad-plane, and tail sitter)10:42 - Ez Tune - simpler tuning for multirotors12:00 - In-flight emergency re-arming15:25 - Timer DMA burst15:51 - Jeti ExBUS protocol fixed and 24 channels available16:06 - Cruise mode for multirotors16:43 - NMEA protocol removed17:12 - GNSS improvements - more constellations and faster communications17:45 - MSP VTX support added18:15 - Linear descent for RTH has changed 20:59 - Pilot logos added to INAV23:41 - Smaller changes in INAV 7.025:41 - Odometer added to the OSD26:27 Changes in INAV 7.126:43 - Multirotors no longer need to us a compass27:48 - Fixed wing autoland31:13 - Add your own custom OSD elements33:22 - The artificial horizon tracks the real horizon when inverted34:08 - New flight mode - Angle Hold34:22 - Smaller changes in INAV 7.134:31 - You can now set a minimum ground speed36:19 - The maximum number of LEDs have been increased to 12836:33 - Add a delay before landing in a Failsafe39:16 - ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 Download the latest configurator from: github.com/iNavFlight/inav-configurator/releases🔗 INAV 7.0 Release Notes: Firmware | Configurator github.com/iNavFlight/inav-configurator/releases/tag/7.0.0🔗 INAV 7.1 Release Notes: Firmware | Configurator github.com/iNavFlight/inav-configurator/releases/tag/7.1.0🔗 INAV 7.0 Pull Requests (Firmware): github.com/iNavFlight/inav/pulls?q=is%3Amerged+is%3Apr+milestone%3A7.0+🔗 INAV 7.1 Pull Requests (Firmware): github.com/iNavFlight/inav/pulls?q=is%3Amerged+is%3Apr+milestone%3A7.1+🔗 INAV 7.0 Pull Requests (Configurator): github.com/iNavFlight/inav-configurator/pulls?q=is%3Amerged+is%3Apr+milestone%3A7.0+🔗 INAV 7.1 Pull Requests (Configurator): github.com/iNavFlight/inav-configurator/pulls?q=is%3Amerged+is%3Apr+milestone%3A7.1+✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#inav7 #inav #fpv
Discover SpeedyBees Mario 5 Quad Frame: Best bang for the buck? Mr.D - Falling with style 2024-03-03 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out the new Mario 5 frame from SpeedyBee. This is the DC (dead cat) version. But standard XH frame versions are also available. If you would like one, they're available here bit.ly/MrD_SpeedyBeeMario5For transparency. This frame was provided by SpeedyBee for review. ✈️ Contents ✈️00:00 Introduction00:22 An overview of the different versions01:20 Some specs on the frames01:55 Unboxing02:15 - Battery strap02:44 - Checking out the standard components included04:15 - What's in the advanced kit?05:07 Some details and different options for the build08:21 Building the frame08:27 - The carbon parts09:23 - Make sure to check the bolt sizes09:50 - The capacitor area and a tip for holding on the arms10:51 - Clear receiver cover and rear TPU piece11:44 - The feet12:11 - The FPV camera area15:10 - XT60 and antenna holder, plus different options16:16 - FC stack16:33 - Bottom complete and pretty rigid16:50 - Stack size and what capacitors will fit in the gap18:05 - Top plate installation18:27 Thoughts after completing the build19:33 My plans for the build. What are your thoughts?20:44 The price22:13 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 SpeedyBee website: speedybee.com/speedybee-mario-5-frame⚙️ Buy the SpeedyBee Mario 5: bit.ly/MrD_SpeedyBeeMario5✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#SpeedyBee #drone #quad
Caddx Walksnail Moonlight 4K Kit: First look and unboxing Mr.D - Falling with style 2024-02-25 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at the new Caddx Walksnail Moonlight 4K Kit. What's it like? How does it perform? Lets find out.✈️ Contents ✈️00:00 Introduction00:57 Product overview02:14 Unboxing02:24 Quick start guide03:22 Accessory bags04:14 Antennas04:32 The Moonlight module10:00 The camera and ND filter12:31 A quick overview of my thoughts of the Moonlight 4K13:37 The installation in my test plane 14:14 Overheating and how I resolved it14:57 Thoughts about the installation17:05 A note if you're planning to use this system with 3S LiIon packs18:03 Best voltage to power the Moonlight 4K18:20 Did I use the ND filter?18:58 Some in flight footage using the Moonlight 4K. All using 4K 60.In the spirit of transparency. This unit was provided by Walksnail for testing.Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ Caddx Walksnail Moonlight 4K Kit: bit.ly/MrD_WalksnailMoonlight4K✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#Walksnail #Moonlight4K
SpeedyBee F405 WING MINI: First look and unboxing Mr.D - Falling with style 2024-02-18 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video, we check out the new SpeedyBee F405-WING Mini flight controller. This is a smaller version of the original SpeedyBee WING flight controller. Though it's smaller. It retains a lot of the features of it's larger sibling. It even has a few tricks the larger one doesn't have. Lets take a look.You can buy one of these from bit.ly/MrD_SpeedyBee_F405WINGMINI✈️ Contents ✈️00:00 Introduction01:01 General info from the manual01:32 Different installation options03:47 An overview of the flight controller11:55 The USB extender board13:34 The PDB board14:49 Wiring diagram15:04 The power flow on the PDB15:40 Important information about the video voltage and considerations for current16:27 Last parts of the manual including setup16:55 Unboxing17:56 Checking out the PDB18:46 USB extender and wireless board19:38 Looking at the flight controller20:13 The accessories20:42 Checking out the USB extender cable21:44 Size comparison to the original SpeedyBee F405 WING APP flight controller22:51 Cables that come with the accessories23:37 Warning for pilots that want to use 2 FPV cameras and use connectors24:43 Some advice if you're not confident soldering26:27 The last accessory pack26:56 Are the standoffs grounds?27:52 Conclusion28:00 One more thing. How does it look in a small aircraft?Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗⚙️ SpeedyBee F405 WING MINI flight controller: bit.ly/MrD_SpeedyBee_F405WINGMINI✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#SpeedyBee #F405-WING #FlightContoller
Removing the Air Speed element from INAVs OSD Mr.D - Falling with style 2024-02-11 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we learn how to remove the airspeed element from the OSD in INAV. But, also why you may want to keep it.✈️ Contents ✈️00:00 Introduction00:29 The OSD page, and showing that Air Speed is not accessible01:30 How to select the Pitot tube for airspeed, or none for disabled02:01 How to remove the Air Speed from the OSD if you want to02:35 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#INAV #AirSpeed
SpeedyBee Meteor LED kit: First look and unboxing Mr.D - Falling with style 2024-01-28 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at the Meteor LED kit from SpeedyBee. This can be used as a standalone LED kit. Or you can hook it up to a UART on your flight controller. To give the flight controller SpeedyBee app compatibility via Wi-Fi or Bluetooth.For clarity. The Meteor LED kit was provided by SpeedyBee for review.✈️ Contents ✈️00:00 Introduction01:20 Some specs and information on the SpeedyBee Meteor02:12 The different wiring options04:05 Unboxing06:27 Where to cut the LED strip if you need to07:00 A look at the Meteor in the Bee35 frame07:25 The module on the Meteor08:14 Using the Meteor LED strip09:45 Using the SpeedyBee app to control the LEDs11:43 Using the SpeedyBee app to connect to the flight controller12:30 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ Buy the SpeedyBee Meteor LED Kit: bit.ly/MrD_SpeedyBeeMeteorLED🔗 SpeedyBee Meteor information: speedybee.com/speedybee-bee35-meteor-led✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#SpeedyBee #LEDStrip
Thanks and a general update Mr.D - Falling with style 2024-01-20 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCFirstly, I wanted to thank everyone on social media who donated to me in the first couple of weeks in January. This was hugely unexpected, and quite overwhelming. But thank you very much. Especially to Nick Boylan who was sharing the links.I also wanted to chat about my recent absence. Plus some things that are coming in the near future.✈️ Contents ✈️00:00 Thank you02:25 Why I've been away04:10 Coming soonThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
INAV Fixed Wing Scaled Throttle: How to get the correct values in your OSD Mr.D - Falling with style 2024-01-07 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video, I show fixed wing pilots how to get your navigation throttles (auto launch, cruise, loiter, RTH, missions etc) showing correctly in INAV.Here are the CLI commands:set max_throttle = 2000set throttle_idle = 0✈️ Contents ✈️00:00 IntroductionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 INAV Hardware In The Loop: youtu.be/EnMx1cFLy4I✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#INAV
INAV 7.0 GPS Page: Are your GNSS settings getting reset? Mr.D - Falling with style 2023-12-31 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out the updated GPS page in INAV Configurator 7.0. This has been catching some people out. As if they select certain GNSS constellations. The are all getting reset. We take a look at that. Plus, have a brief revisit of setting up the GPS and what to look out for if you have problems.✈️ Contents ✈️00:00 Introduction00:35 Update to the latest version of Configurator02:00 What has changed on the GPS page02:09 Replicating the problem that pilots are having02:25 Why is this happening? What to do about it05:40 Which protocol should you use?06:10 Getting the right time and date from the clock06:30 How to know if the GPS is working properly09:14 Why can't I arm with 6 satellites?09:48 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
Setting up telemetry and sensor widget screens on ETHOS Mr.D - Falling with style 2023-12-17 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at how to add readouts for telemetry, channels, switches, and more on your home screen. Hell, you can even have multiple screens. This video comes in response from a viewer's question, asking how to display the aircraft voltage on the home screen. We look at how to do that and more.✈️ Contents ✈️00:00 Introduction00:27 An overview of the telemetry screens and widgets02:27 Changing a widget04:35 Getting telemetry sensors from the receiver06:06 Adding the receiver voltage to the home screen06:38 Getting the battery voltage if the battery is not directly plugged in to the receiver07:25 Making sure that the AIN2 pin can handle the voltage output of our battery08:22 Making up a cable to attach the battery to the AIN2 plug09:11 Setting the widget to use AIN209:42 Tuning the sensor to display the correct voltage12:08 What if the values are red?12:17 Changing layouts and adding multiple sensor widget screens13:19 Adding a new screen layout15:50 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #ETHOS #Telemetry
SpeedyBee Bee35 Pro frame First look Mr.D - Falling with style 2023-12-03 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out the new SpeedyBee Bee35 Pro 3.5 inch cinewhoop frame.✈️ Contents ✈️00:00 Introduction00:30 Checking out the prices on the web site01:09 Unboxing02:38 A closer look at the parts in the box07:22 The built frame and my experience while building it07:58 The one thing to watch out for in the build manual10:20 Conclusion11:16 One thing to consider if you're new to building quadsThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ SpeedyBee Bee35 Pro frame: bit.ly/MrD_SpeedyBee_Bee35Pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#SpeedyBee #quad
RunCam Phoenix 2SP: First look and unboxing Mr.D - Falling with style 2023-11-26 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at the RunCam Phoenix 2SP. We take a look at the specs and how the image of the camera looks. This is my first FPV camera review, so if you have any constructive criticism. Please feel free to leave it in the comments.This FPV camera has been provided by Banggood.✈️ Contents ✈️00:00 Introduction00:37 Unboxing03:30 My test rig05:01 The specs of the comparison camera05:48 Comparing the image quality06:45 - Flare tests07:25 - Low light tests09:50 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ RunCam Phoenix 2SP: bit.ly/MrC_RunCamPhoenix2SP✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
Understanding the different FrSKY Stabilised Receivers Mr.D - Falling with style 2023-11-19 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out the different types of FrSKY stabilised receivers. Each type has a differences including the channel map, self test activation method, and the tools you use to configure them. I look at the current and historical stabilised receivers, and how each type is used.This video doesn't go into depth about how to set up and calibrate the receivers. For more information on that. Check out these videos:Archer Plus/TD SRx: youtu.be/gzc1VwEPfCEArcher SRx: youtu.be/rUKIBQdmvIYSxR: youtu.be/SQ-cpXhrL5A✈️ Contents ✈️00:00 Introduction01:01 The different types of FrSKY stabilised receivers04:54 The different channels used for the stabilisation functions07:20 Which tools to use for the different types of receiver09:46 Self check on the different types of receiver11:25 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
Its here! INAV 7.0 RC1 Mr.D - Falling with style 2023-11-05 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at INAV 7.0 RC1, if you should install it, what you may need to do if you do install it.✈️ Contents ✈️00:00 Introduction00:29 Should you use INAV 7.0 RC1?01:23 Where can you find the information for RC1?01:50 How do you download INAV 7.0 RC1?02:44 If you do use Release Candidates, make sure you keep up to date03:24 Where to find the release notes03:59 What are the major changes in INAV 7?11:45 Other changes to be aware of14:50 Where to report issues if you find any16:03 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 Releases and reporting issues video: youtu.be/Eul5BLyLoP0🔗 INAV Firmware GitHub: github.com/iNavFlight/inav🔗 INAV Configurator GitHub: github.com/iNavFlight/inav-configurator✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#INAV #INAV7.0 #INAV7.0RC1
Read out the battery voltage and other values on your ETHOS transmitter Mr.D - Falling with style 2023-10-29 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we look at how to have your ETHOS transmitter read out values, for example the battery voltage. This can pretty much be any value on ETHOS, including all the telemetry sensors you have discovered. In the video, we take the battery voltage as an example. Showing how it can be read out from operating a switch. Or automatically read out when the value exceeds a specified target.✈️ Contents ✈️00:00 Introduction00:31 Getting the telemetry sensors02:37 Creating a special function to simply read out a value04:01 Having the value automatically read out when a threshold is passed07:25 Fixing the mistake in the BATT LOW logic switch08:25 Having the value read out at a set interval09:47 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #ETHOS #LogicSwitch
SpeedyBee 5.8GHz Video Receiver: First look Mr.D - Falling with style 2023-10-22 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out the new 5.8GHz analogue video receiver from SpeedyBee. If you're interested in buying one of these receivers. They can be bought globally from bit.ly/MrD_SpeedyBee58VRx✈️ Contents ✈️00:00 Introduction01:50 Unboxing02:28 The supplied antennae05:54 The 5.8GHz VRx module07:27 Functions available on the module09:39 My thoughts on missing features11:22 Antennas on the VNA ...or not11:52 Wrapping upThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗⚙️ SpeedyBee 5.8GHz analogue video receiver: bit.ly/MrD_SpeedyBee58VRx✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#SpeedyBee #FPV
Using the multi function buttons with ETHOS: The modes and how to output on a single channel Mr.D - Falling with style 2023-10-15 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out the multifunction buttons that are on all the latest FrSKY transmitters. On the X18, X20, and XE, there are 6 buttons at the bottom centre of the transmitter. On the TWIN X-Lite, there are 4 buttons, just below the screen. This video shows how this works on an X20. But it's the same on all the transmitters. With the X-Lite, you will have 4-pos, 4pos with off, 4 x 2 pos, and momentary modes. All the different button modes are explained. Plus, I show how to get 2x3 pos, 6-pos, and 6-pos with off modes operating on a single channel.✈️ Contents ✈️00:00 Introduction00:35 Where to change how the multifunction button works01:15 6-pos or 4-pos on the TWIN X-Lite01:33 6-pos with off or 4-pos with off on the TWIN X-Lite01:46 2 x 3 pos02:17 6 x 2 pos or 4 x 2 pos on the TWIN X-Lite02:48 Momentary03:02 How to set up the switches that need additional programming07:32 How to use the multifunction switch in addition to a traditional switch11:56 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #ETHOS #ETHOSProgramming
Inside the FrSky TANDEM X20 Pro: Adjusting gimbals and changing mode Mr.D - Falling with style 2023-10-08 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look inside the FrSky Tandem X20Pro transmitter. Not only can you find out how to take this radio apart. But we also look at the most performed tasks inside the radio. Including:- Gimbal adjustment- Swapping to mode 1, 3, or 4- Rotating the gimbals- Replacing the RTC battery✈️ Contents ✈️00:00 Introduction01:03 About the back, and what parts you may need to remove02:57 Changing the real time clock (RTC) battery02:18 Rotating the gimbals02:46 Information about the antenna configuration04:01 Removal of the central part of the rear case (shown in reverse)06:04 Adjusting the gimbals and changing mode08:12 Removing the rear side panels (shown in reverse)10:16 Make sure that the radio is still working OK after taking the back off10:44 The changes in ETHOS needed to switch mode11:36 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSky TANDEM X20Pro transmitter: bit.ly/MrD_FrSKYX20Pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSky #X20Pro
SpeedyBee F405 V4 55A Stack: Unboxing and first look Mr.D - Falling with style 2023-09-29 | In this live broadcast, we check out the new SpeedyBee F405 V4 Stack. This is an update to the SpeedyBee F405 V3 stack, which really impressed me. I've been flying the V3 in my AOS 5, and it has been faultless. This update brings some nicer hardware, more power handling, and is still the same awesome price.This is my first time trying a live unboxing. Did it totally suck, or is there some hope? What did you think? Leave me a comment and let me know.The main differences between the V3 and V4 are:Flight controller:The V 3 has a BMI270 gyro, whereas the V4 now uses an ICM42688P. The V4 has an improved LDO power chip for the gyro with much better surge protection. The V4 can handle 3A on the 5v and 9v BECs, compared to 2A on the V3. The V4 has DSHOT support on INAV from the get go. V3 currently doesn't work with DSHOT on INAV. But an update in INAV 7 will get this working. The SD card reader chip is better quality and more reliable.ESC:Continuous current is now 55A, up from 50A. The burst current is now 70A, up from 55A. The copper traces are thicker. There is now an aluminium heatsink. The MOSFETs have a lower internal resistance, and there are more filtering capacitors. The V4 is about 10g heavier than the V3; about half of this increase is due to the heat sink.This new stack can be found at speedybee.com/speedybee-f405-v4-bls-55a-30x30-fc-esc-stackContents00:00 Waiting screen (skip this)06:27 Introduction07:42 Unboxing08:00 - The 55A 4-in1 ESC10:08 - The flight controller14:39 About DSHOT on INAV, and how it will work with the v3 in INAV 7.015:55 - The accessories20:25 Pinouts on the flight controller24:44 ConclusionIf you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.There are more tutorials on my web site at https://www.MrD-RC.com. You can also join like-minded people at the Fixed Wing RC Rebels group on Facebook. Also, if you found my videos useful, and would like to leave me a little tip, you could always buy me a Coffee at mrd-rc.com/go/ko-fiThank you for your time, and don't forget to fly it like you stole it!#SpeedyBee #F405 #FPV
A better hands free climb/descent for INAV, ArduPilot, and other flight controller firmware Mr.D - Falling with style 2023-09-24 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video, we revisit a nice addition to your transmitter model. This will allow you to climb or descend as a set rate. I have shown you how to do this before. But this new version is much better. Now you can enable and disable your climb or descent without needing to change the rate. There are also nice automated entries and exits for this assistance feature.✈️ Contents ✈️00:00 Introduction01:16 How the old version worked, and how the new version will work02:08 How I have the basic models setup on the transmitters02:47 Step 1 - Disable the trims (OpenTX/EdgeTX)03:35 Step 1 - Disable the trims (ETHOS)04:15 Step 2 - Adding the pot and curve for the hands free climb/descent (ETHOS)07:07 Step 2 - Adding the pot and curve (OpenTX/EdgeTX)09:33 Step 3 - Setting up the logic and assigning it to the mix (OpenTX/EdgeTX)10:15 - Logic for detecting the flight modes12:12 - Logic to activate the hands free climb/descent14:45 - Logic to deactivate hands free climb/descent16:25 - Latching switch for hands free climb/descent enabled17:35 - Setting up the switching in the mixer17:58 - Demo of the system working19:00 Step 3 - Setting up the logic and assigning it to the mix (ETHOS)19:02 - Logic for detecting the flight modes21:40 - Logic to activate the hands free climb/descent23:55 - Logic to deactivate hands free climb/descent25:59 ETHOS comments and how they can be really useful27:09 - Latching switch for hands free climb/descent and the OR for activating29:25 - Setting up the switching in the mixer29:50 - Demo of the system working30:50 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSky TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro⚙️ FrSky Horus X10S Express transmitter: bit.ly/MrD_3l7b8K5✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#INAV #AutoClimb #OpenTX #EdgeTX #FrSkyETHOS
Moving models and more between two ETHOS transmitters Mr.D - Falling with style 2023-09-17 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out how to transfer modes, audio, LUA, and bitmaps between ETHOS transmitters. This is particularly useful if you have changed or upgraded transmitters. The moving process is pretty simple. But make sure that your moved models work as expected before flying. Especially if moving between transmitters that have different switches and buttons. You will likely need to re-register and re-bind your receivers.✈️ Contents ✈️00:00 Introduction00:10 Step 1 - Make sure the firmware version matches01:17 Step 2 - Find out where things are stored on each transmitter01:43 Step 3 - Transferring the files via your computer02:52 Selecting the correct to and from drives04:42 Copying the models05:22 Copying other files, like logs, model images, and audio08:53 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 Updating ETHOS using ETHOS Suite: youtube.com/watch?v=fvxbYacd-bk&t=382s⚙️ FrSKY TANDEM X20S: bit.ly/MrD_3x6n6JL⚙️ FrSKY TANDEM X20Pro: bit.ly/MrD_FrSKYX20Pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #MoveModels #ETHOS
FrSKY X20 Pro : First look and unboxing Mr.D - Falling with style 2023-09-10 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video, we check out the new flagship transmitter from FrSKY. The TANDEM X20 Pro. This is a radio that has been talked about for some time. Now it's finally here, and we can take a look at it in the flesh. The X20Pro is available now. Though you may have a wait if you want to buy one. Due to the CNC machined body, there is already a waiting list for this transmitter. Only 4 of the aluminium bodies can be produced a day, meaning 20 radios per week. In the video, we will take a general look at the radio, see how it compares to the original X20, and also chat about that price tag.If you're interested in this transmitter. It can be purchased globally from bit.ly/MrD_FrSKYX20ProTL;DW This is a high quality, premium radio. Every switch and dial feels like it will last decades; and has a reassuring click, pressure, or centre detent. Everyone that I have shown the X20 Pro to has commented on how great the switches feel, and the general excellence of the build.✈️ Contents ✈️00:00 Introduction00:52 How much does it cost?01:06 Unboxing: The case01:31 - Included accessories04:23 Comparing the X20S and the X20Pro06:38 How much does the X20Pro weigh?07:19 The X20Pro hardware10:19 Ports, module bay, and battery11:20 The CNC machined aluminium case11:36 A quick look at ETHOS12:08 Text to speech13:39 Calibrating the gimbals, pots, and sliders14:58 Setting the date and time15:50 The three different RF systems available on the internal ISRM module19:23 IMPORTANT: Check your firmware version before using the transmitter in flight19:55 Updating ETHOS21:21 The different file areas on the X20 Pro24:06 If you still have the bootloader screen after updating24:40 General thoughts on the X20 Pro26:15 Is the X20 Pro worth the extra cost?29:50 Conclusion and upcoming videosThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 FrSKY ETHOS Feedback Community: github.com/FrSkyRC/ETHOS-Feedback-Community⚙️ FrSKY TANDEM X20Pro transmitter: bit.ly/MrD_FrSKYX20Pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #X20Pro
RadioMaster Zorro LE : First look and unboxing Mr.D - Falling with style 2023-09-03 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out the Limited Edition RadioMaster Zorro transmitter. This is a small, gamepad style transmitter. This type of transmitter is ideal for flying quads, or for transporting in a backpack. How does the Zorro stack up? Lets take a look.The Zorro LE is available from Banggood here bit.ly/MrD_RadioMasterZorroLE✈️ Contents ✈️00:00 Introduction00:25 What's in the box02:22 Checking out the radio06:36 Setting the clock06:52 Calibrating the gimbals and sliders09:21 The external antenna10:04 The little plastic doors10:28 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ RadioMaster Zorro Limited Edition: bit.ly/MrD_RadioMasterZorroLE✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
Updating FrSKY RB firmware and installing the ETHOS LUA script RB25 RB25S RB35 RB35S Mr.D - Falling with style 2023-08-20 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video, we look at how to update the RB25, RB25S, RB35, or RB35S. We go through all the steps, from downloading the firmware, software, and scripts. To installing them on your RB device and ETHOS transmitter. Currently, prerequisites for installing this firmware on your RB device is the STK Tool. There is a link to the tool below.✈️ Contents ✈️00:00 Introduction00:48 Downloading the firmware for the RB device, ETHOS LUA scripts, and the STK software02:34 Installing the Windows driver for the STK adapter, if you need it03:20 Extracting the STK update tool03:34 Extracting the RB firmware to the desktop03:52 Preparing the RB device for update05:16 Flashing the RB device with the new firmware06:50 Installing the RB device LUA scripts on your transmitter06:58 Where to install the LUA scripts07:42 Connect the transmitter to your computer07:49 Copying the files to the correct drive on your transmitter09:48 Locating the RB LUA tools on the transmitter10:38 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 FrSKY website: ⚙️ FrSKY Tandem X18 transmitter: bit.ly/MrD_3LD7R1j⚙️ FrSKY RB35S: bit.ly/MrD_FrSKYRB35S⚙️ FrSKY STK tool: bit.ly/MrD_FrSKYSTK✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #RB25 #RB35
SonicModell Baby AR Wing Pro Build, Maiden, and Review Mr.D - Falling with style 2023-08-13 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we finally get to maiden the @SonicModellOfficial Baby AR Wing Pro. Before we do, I take a quick look at my build and the good and bad points. Then we see how this thing flies. How good is it? Watch and find out 😉The Baby AR Wing Pro is available from Banggood here mrd-rc.com/go/sonicmodell-baby-ar-wing-pro✈️ Contents ✈️00:00 Introduction00:17 The build process and how I built mine05:15 Caution if you want to remove the wings06:20 The flight controller setup07:11 Time to fly!! ...and my mistake08:43 Changes due to the ESC dying and burning out the motor10:21 The real maiden flight12:20 How does the Baby AR Wing Pro stall?16:40 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ SonicModell Baby AR Wing Pro: mrd-rc.com/go/sonicmodell-baby-ar-wing-pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#SonicModell #BabyARWingPro #ARPro
SonicModell Baby AR Wing Pro maiden and review, this afternoon! #fpv #inav #BabyARWingPro Mr.D - Falling with style 2023-08-13 | Check out more about the Baby AR Wing Pro youtu.be/Cn_AJR5D65A
HD FPV: Why DJI ARE the bad guys Mr.D - Falling with style 2023-08-02 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCThis is a bit of a different video for me. It's not really a tutorial or review. But more just passing along some information to dispel some mistruths that are going around. In particular, this video comes as a result of seeing some of the comment's in Mads Tech's (@MadRC) video "DJI Goggles 2 & O3 FPV Do Not Buy - They Just Don't Care" (youtu.be/r72p6bI63Dg). In this video, Ian makes a lot of harsh, but fair comments about DJI, and this whole mess with their firmware.One guys' comments in particular caught my eye, stating: "INAV devs CAN fix this, but they are stubborn and just won't bother. Why not blame the INAV devs?" and "Yeah, INAV devs can fix this, but they want drama in the community." Other than the INAV developers and community being the least likely to cause "drama". The INAV community is genuinely one of the most helpful I've been involved with. It is showing that some people don't actually know what's going on here.The INAV devs did a lot of work to get even a basic level of OSD for O3 pilots. Something that they should not have even needed to do, if DJI had done things properly.Hopefully this video will go some way to show exactly what the problem is. Why it is 100% DJIs fault, how INAV devs are actually going above and beyond to support O3 pilots, and why the font is so important. TL;DR, it isn't just about the characters looking different!✈️ Contents ✈️00:00 Introduction01:46 All about MSP DisplayPort and why this isn't the problem04:43 The differences between the font sets05:21 Comparing with BetaFlight's base font06:20 Comparing with ArduPilot and INAV08:30 Is INAV just causing drama?09:14 What is the real fix, and why DJI are the only people who can do it09:53 Why you shouldn't by DJI!11:03 Why don't BetaFlight pilots understand the issue fully?12:30 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 Mads Tech Channel: youtube.com/@MadRC✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#DJI #HDFPV #DontBuyDJI
FrSKY ETHOS: Using a linear control as a switch - using the red slider for throttle cut Mr.D - Falling with style 2023-07-30 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCThis video is to answer a question I received from a viewer on how to use the red slider for throttle cut. This technique can be used to turn any linear control (slider or pot) in to a switch. So it could be used for a multitude of tasks.✈️ Contents ✈️00:00 Introduction01:08 Creating the Logic Switch03:07 Assigning the Logic Switch to the throttle cut03:50 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY TANDEM X20S Transmitter: bit.ly/MrD_3x6n6JL✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #ETHOS #LogicSwitch
Re-arming in flight with INAV Mr.D - Falling with style 2023-07-23 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at what you should do if you accidentally disarm in flight, when flying with INAV. I have seen posts and messages from quite a few people who don't know what to do, and have lost models because of this. So I thought I'd make a quick video to show that it is possible to re-arm in flight. Not only that; it's actually pretty easy. TL;DW, Stay calm, get rid of the stats screen, and check for blocking messages on the system messages.✈️ Contents ✈️00:00 Introduction00:30 Re-arm in flight without any restrictions00:47 Why can't you just re-arm?01:00 - Modes that will or won't let you arm01:59 - Throttle position02:09 - Autolaunch permanently enabled?02:54 Having a fly, disarming, and recovering07:29 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 Immediate re-arm in flight video: youtu.be/ndxtVzC7LHA🔗 How to use the HITL: youtu.be/EnMx1cFLy4I✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!
Setting up and flying Waypoint Missions in INAV Mr.D - Falling with style 2023-07-16 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at how to set up a basic waypoint mission in INAV. I'm using version 6.1.1. so some of the options may not be available on older version. We look at:- The mode you need to fly a waypoint mission- What settings are available on the Advanced Tuning page- How to set up a basic mission in Mission Control- Flying the missionThis should give you all the information you need to know to setup and fly your first INAV mission.NOTE: Please do not fly a mission before making sure that your aircraft is fully set up and correctly tuned. You should be 100% confident that the aircraft can fly safely and reliably in both standard and navigational flight modes. For example, if RTH is not smooth and predictable. Do not fly a mission until is it setup and tuned correctly, so that it is.✈️ Contents ✈️00:00 Introduction00:21 What do you need on the transmitter?00:41 How I'm demonstrating this00:56 Adding the NAV WP mode01:17 The Waypoint Navigation settings on the Advanced Tuning page02:11 - Waypoint Radius02:47 - Waypoint Safe Distance03:22 - Load Waypoint on Boot03:43 - Enforce Altitude at Waypoint04:40 - Waypoint Tracking Accuracy05:07 - Waypoint Tracking Angle05:42 - Waypoint Turn Smoothing06:28 - Restart Waypoint Mission07:09 Planning the mission in Mission Control07:39 - Set the first waypoint within the Waypoint Safe Distance from your arming position08:06 - Moving the map and markers08:20 - Creating a basic mission09:20 - Setting waypoint options09:48 - Getting the approximate ground elevation data and how to stay above it11:00 - Speed11:30 - Waypoint types and setting RTH on the last waypoint12:08 - Saving and checking the mission13:09 Flying the mission14:07 - The indicator for NAV WP mode14:19 - Indicators for the next waypoints17:20 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 INAV Stick commands: mrd-rc.com/tutorials-tools-and-testing/inav-flight/inav-stick-commands-for-all-transmitter-modes⚙️ FrSKY TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#INAV #WaypointMissions
How to use your own logo on the top of the ETHOS screen Mr.D - Falling with style 2023-07-02 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video, we look at how to put your logo at the top of the ETHOS screen. The process it's self is pretty simple. But there is one key step that you must do, to have your logo appear.✈️ Contents ✈️00:00 Introduction00:25 Which logo are we changing?01:00 How to get to the file we need to change02:42 What people usually try to get this working03:50 How to upload the logo and have it actually change05:12 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #ETHOS
Want to know my thoughts on Remote ID? Check out CurryKitten’s video. He nailed it! Mr.D - Falling with style 2023-07-01 | If you want to know my thoughts on what the FAA are doing in the states and the whole Remote ID calamity. Please check out @CurryKitten’s recent video. I 1000000% agree with what he says in the video. So please watch it and share it extensively. If the UK government are thinking of introducing such measures. Then they really at a gaggle of morons too! Stop it! It’s stupid!youtu.be/4mkjiVbk5w8#SayNoToRemoteID
How to fix configuring the Archer Plus stabilised receivers: Installing the FrSKY SRX LUA scripts Mr.D - Falling with style 2023-06-25 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCA few people have contacted me, having problems configuring Archer Plus stabilised receivers, such as the SR10+. The SXR Tool no longer works for these receivers, and changes revert back to their old stated. The solution is to install new SRX LUA script tools These add new calibration and setup tools for the Archer Plus stabilised receivers. These new tools will be included as part of ETHOS 1.5. But, until then. We need to install them ourselves.In this video, we have a quick overview of making sure everything is up to date. For full videos on updating, please see the links below. After that, we download and install the LUA script tools. Next, we have a quick look at the tool. If you have used the old SxR Tool. The new SR tool is very familiar. Only some of the names have changed to make things clearer.✈️ Contents ✈️00:00 Introduction00:35 Make sure the transmitter operating system firmware (ETHOS) is up to date03:15 Updating the RF or receiver firmware03:47 Where can you find the versions of the RF and receiver firmware installed?04:08 Downloading the firmware to the transmitter04:55 Downloading the RF module from the FrSKY site05:08 Downloading the receiver firmware from the FrSKY site07:03 Updating the internal RF module firmware08:19 Updating the receiver firmware10:49 Downloading and installing the SRX LUA script13:12 Where is the new SRX setup tools?13:43 Checking out the new SRX configuration tool17:18 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 Updating ETHOS: youtube.com/watch?v=fvxbYacd-bk&t=382s🔗 Updating the transmitter's RF module: youtu.be/3DmDUWopO-0🔗 Updating receiver firmware: youtu.be/9tncdNDinFM⚙️ FrSKY TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL⚙️ FrSKY Archer Plus SR10+ receiver: bit.ly/MrD_FrSkySR10Plus✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #SR10 #LUA
First look at the SonicModell Baby AR Wing Pro Mr.D - Falling with style 2023-06-18 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a first look at the new SonicModell Baby AR Wing Pro. I have been sent the PnP version for review, so lets take a look at what we get. What are my thoughts about the model. Is this a real replacement for the Mini AR Wing?This was supplied to me for review from Banggood. If you would like to buy it from them. This discount code will get you some money off. It will work until 30/06/2023.The Baby AR Wing Pro is available from Banggood here: mrd-rc.com/go/sonicmodell-baby-ar-wing-proCode: BG3745a2✈️ Contents ✈️00:00 Introduction00:46 Unboxing01:08 Stickers and the instructions02:04 Specs04:27 Carbon spar, accessory pack, and prop05:12 The wings07:39 Winglets08:06 The body, ESC and motor09:17 Comparing the Mini AR Wing motor with the Baby AR Wing Pro10:01 A quick build and checking out the battery space12:16 The space for the FPV camera12:30 airflow not optimal12:54 Comparing the size of the Mini AR Wing and the Baby AR Wing Pro13:14 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ SonicModell Baby AR Wing Pro: mrd-rc.com/go/sonicmodell-baby-ar-wing-pro✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#SonicModell #BabyARWingPro #BabyARPro
First look at the FrSKY RB35S Flight Safe System Mr.D - Falling with style 2023-06-11 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at the FrSKY RB35S. This is a part of FrSKY's Flight Safe group of products. Designed to keep your model in the air and in control. In this video we look at what the RB35S is, what it does, and what you get with it. In coming videos, we'll check out flashing and setting it up. Also, there will be a video on the stabilisation system.✈️ Contents ✈️00:00 Introduction00:43 What is Redundancy Bus?03:36 Unboxing the RB35S05:06 Size and weight of the RB35S05:45 Overview of the RB35S05:48 Power input redundancy06:05 Connections on the side06:15 The power outputs and BEC explanation06:51 The PWM outputs07:20 The Receiver and LED ports08:44 Feature overview10:47 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY RB35S: bit.ly/MrD_FrSKYRB35S✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY
How to calibrate gimbals, pots, and sliders in ETHOS Mr.D - Falling with style 2023-05-28 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we discover how to calibrate gimbals, pots, and sliders in FrSKY ETHOS.✈️ Contents ✈️00:00 Introduction00:14 Where is the calibration tool?00:34 Centring all the sliders, pots, and gimbals01:20 Performing the calibration02:43 Testing the calibration03:10 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY TWIN X-Lite: bit.ly/MrD_TWINXLite✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #CalibrateGimbals #FrSKYETHOS
Downgrading Walksnail Avatar firmware Mr.D - Falling with style 2023-05-21 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we look at how to downgrade the firmware on the Caddx Walksnail Avatar FPV HD video system. Where to download the old firmware? How can you make it overwrite more recent firmware? Will it stop you updating to new firmware in the future?✈️ Contents ✈️00:00 Introduction00:36 Where do we download the older firmware from?01:08 Why can't we just use the standard old firmware file?01:33 Downloading the firmware01:51 Renaming the downloaded image files02:50 Flashing the old firmware to the goggles05:26 Checking the newly flashed firmware number05:54 Will renaming the firmware stop you from updating to the next firmware?07:09 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 Where to download the firmware: avatar-firmware.d3vl.com⚙️ Avatar system (Goggles, VTx, and Camera): bit.ly/MrD_WSAV_Goggles_ProCam⚙️ Avatar VTx & Pro Camera: bit.ly/MrD_WSAvatar_ProKit⚙️ Avatar VTx & V2 Camera: bit.ly/MrD_WSAvatar_V2Kit✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#Walksnail #Caddx #downgrading #WalksnailWiki
Working with Profiles in INAV: Using different batteries or PIDs Mr.D - Falling with style 2023-05-14 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we look at how to work with profiles in INAV. There are two types of profile: control profiles and battery profiles. These can be used to change settings based on the battery you plug in, a switch position, or manually set via stick commands. You can even change control profiles based on data from your flight controller via the programming tab. For example having different control profile based on your speed.Most people will likely only need the battery profiles. Chances are that you may want to fly with different chemistry batteries, different capacity batteries, or different cell counts. If so, using the battery profiles is the best way to set this up.✈️ Contents ✈️00:00 Introduction00:24 What are profiles?01:02 How can you tell which settings are part of a profile?01:24 Setting up the first battery01:50 How to set up the profile for a second battery02:51 Copying base changes from our main profile (1) to a new profile07:04 Switching battery profiles automatically based on cell count07:24 Finding the document for battery settings on GitHub09:25 Changing control profile automatically, based on your battery profile11:54 Finding the document for control profiles on GitHub12:14 Changing control profiles with a switch13:10 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 Battery document: github.com/iNavFlight/inav/blob/master/docs/Battery.md🔗 Control profile document: github.com/iNavFlight/inav/blob/master/docs/Profiles.md✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#INAV #batteryprofiles
Organising your models in ETHOS Mr.D - Falling with style 2023-05-07 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we take a look at how to organise models in ETHOS. We check out how to make new model categories. Also how to move existing models.✈️ Contents ✈️00:00 Introduction00:30 Creating a new category for your models01:14 Creating a new model within a category01:29 Moving a model to a different category02:19 How to delete a category03:34 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY TWIN X Lite transmitter: bit.ly/MrD_TWINXLite✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSky #ETHOS
First look at the SpeedyBee F405 WING flight controller Mr.D - Falling with style 2023-04-30 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we check out the new SpeedyBee F405 WING flight controller. At the time of purchase, this flight controller was only $39.99 (about £33). Which is an absolute bargain. Unfortunately, there are a few silly things to be aware of. What are my thoughts? Lets take a look.✈️ Contents ✈️00:00 Introduction00:17 Opening up the box00:32 Included MicroSD card00:58 The paper manual02:42 The accessories04:28 - Remote USB Type-C board05:16 The Power Distribution Board05:40 - Switching the VTx and Camera voltage06:14 - Changing the servo voltage06:27 - The amp specs for the PDB07:02 The Flight Controller board07:10 - Signal out for the motors and servos07:49 - Connecting a receiver09:57 - Airspeed sensor connections11:22 - The front connections14:18 - The unfortunate position of the MicroSD card slot16:33 The Wireless top board16:41 - LED connectors17:25 - Power indicator LEDs17:55 - The wireless parts18:25 The assembled flight controller19:19 Potential problems when using the solder pads. Another reason to lose the connectors20:34 The not so remote, remote USB adapter21:43 First thoughts on the flight controller22:27 This board is an F411 killer!23:36 Size comparison between the SpeedyBee F405 WING and the MATEKSYS F405-WING and F765-WSE25:18 The cool logo, which is also the flight controller forward direction arrow25:31 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ SpeedyBee F405 WING: bit.ly/MrD_SpeedyBeeF405WING✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#speedybee #flightcontroller
How to record log files with ETHOS Mr.D - Falling with style 2023-04-23 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCIn this video we look at how to record log files on your ETHOS transmitter. I show two recording methods. One records all the time. The other only records when your throttle or arm switch is active. There's no use recording log files if you don't know how to find them. So I also show where they are on the transmitter; and how to access them on your PC.✈️ Contents ✈️00:00 Introduction00:21 How the model is currently set up00:53 How to set up logs to record all the time01:20 The logging settings02:31 How to set up the logs to only record when the throttle is active03:02 How to access the log files on the radio03:42 Accessing the logs on your computer07:39 What can you do with the log files?08:07 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️⚙️ FrSKY TANDEM X20S Transmitter: bit.ly/MrD_3x6n6JL✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#FrSKY #ETHOS #LogFiles
Why is INAV stuck in Manual mode? Mr.D - Falling with style 2023-04-16 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RCA few people have had a problem recently where INAV is stuck in Manual on the modes page. Fortunately, this is a really easy problem to fix. I show you how in this video.✈️ Contents ✈️00:00 Introduction00:48 Why is INAV stuck in manual, and how to fix it.01:50 ConclusionThank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.✈️ In this video ✈️🔗 How to calibrate the accelerometer: youtu.be/1f_G0hKOUoQ?t=1897⚙️ FrSKY TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL✈️ Help other RC pilots find this video ✈️If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.✈️ Supporting me and other resources ✈️🛩 There are more tutorials on my web site at https://www.MrD-RC.com.🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.🛩 Join the channel's discord server at discord.gg/HMvrgZX6su🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.Thank you for your time, and don't forget to fly it like you stole it!#INAV #manualmode
