iNav 5.0 Beginners Build Academy: Lesson 03 - Installing iNav and the pre build setup @MrD

Mr.D - Falling with style 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

This is the third video in the iNav 5.0 build series for beginners. In this series we will start from the ground up, building the plane, installing the hardware, and installing iNav. We will discuss all the important things along the way, to give you a good start in the hobby. At the end we will go through a pre-maiden checklist, just to make sure that everything is as ready as can be. Then we will fly the plane. The plan is to have a new video every other week until the first flight.

The full iNav 5.0 Beginner's Build Academy can be found at youtube.com/playlist?list=PLtuty5zAsZ_aKbk9h9hbVG-TySq1W4C14

In this video we finally get our hands on iNav. I show where to download it and how to install it on Windows. We have a look at the flight controllers and take a look at some of the different connections on them. Don't worry if this all seems confusing at the moment. This is just an introduction, and we will connect everything together in later videos. Next we flash iNav to the flight controller and go over some pre-FPV setup steps. These steps make sure that the flight controller is OK, before we start soldering to it. But also shows us where we need to connect our servos.

✈️ Contents ✈️
00:00 Introduction
00:44 Downloading and installing iNav
06:02 Looking at the flight controller and explaining where things connect
06:30 - What comes with the flight controllers?
09:31 - The barometer and covering it with open cell foam
10:35 - Looking at the flight controllers
11:06 - What are the arrows on the flight controller
11:40 - Where to connect the power for the battery and ESC
12:25 - What is the shunt resistor?
13:31 - Servo power and BEC power rails
15:36 - Servo and motor connections
15:55 - What is a UART, and what connects to them?
18:30 - Connecting the analogue video camera and transmitter
21:15 - Where to plug in the USB cable
21:45 Getting started with iNav
22:54 - How to get the flight controller in to DFU mode
23:56 - Connecting to the flight controller
24:48 - What is flashing?
25:05 - Finding the right target for the flight controller
27:08 - Flashing iNav 5.0 to the flight controller
30:07 - Setting up the correct platform default values
31:37 - Calibrating the accelerometer
32:31 -- What is the accelerometer? And how do we know which way up the flight controller needs to be?
37:35 -- The calibration process
39:44 - Checking the movement on the setup page
41:26 - A quick overview of the mixer
42:18 - Pre-arming checks are ok, then so is the flight controller
43:11 Thinking about part layouts
48:06 Conclusion and what is in the next video

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 The iNav Configurator GitHub: github.com/iNavFlight/inav-configurator
🔗 ImpulseRC Driver Fixer: impulserc.com/pages/downloads
⚙️

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

updated 2 years ago

iNav 5.0 Beginners Build Academy: Lesson 03 - Installing iNav and the pre build setup

Mr.D - Falling with style 2022-07-17 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

This is the third video in the iNav 5.0 build series for beginners. In this series we will start from the ground up, building the plane, installing the hardware, and installing iNav. We will discuss all the important things along the way, to give you a good start in the hobby. At the end we will go through a pre-maiden checklist, just to make sure that everything is as ready as can be. Then we will fly the plane. The plan is to have a new video every other week until the first flight.

The full iNav 5.0 Beginner's Build Academy can be found at youtube.com/playlist?list=PLtuty5zAsZ_aKbk9h9hbVG-TySq1W4C14

In this video we finally get our hands on iNav. I show where to download it and how to install it on Windows. We have a look at the flight controllers and take a look at some of the different connections on them. Don't worry if this all seems confusing at the moment. This is just an introduction, and we will connect everything together in later videos. Next we flash iNav to the flight controller and go over some pre-FPV setup steps. These steps make sure that the flight controller is OK, before we start soldering to it. But also shows us where we need to connect our servos.

✈️ Contents ✈️
00:00 Introduction
00:44 Downloading and installing iNav
06:02 Looking at the flight controller and explaining where things connect
06:30 - What comes with the flight controllers?
09:31 - The barometer and covering it with open cell foam
10:35 - Looking at the flight controllers
11:06 - What are the arrows on the flight controller
11:40 - Where to connect the power for the battery and ESC
12:25 - What is the shunt resistor?
13:31 - Servo power and BEC power rails
15:36 - Servo and motor connections
15:55 - What is a UART, and what connects to them?
18:30 - Connecting the analogue video camera and transmitter
21:15 - Where to plug in the USB cable
21:45 Getting started with iNav
22:54 - How to get the flight controller in to DFU mode
23:56 - Connecting to the flight controller
24:48 - What is flashing?
25:05 - Finding the right target for the flight controller
27:08 - Flashing iNav 5.0 to the flight controller
30:07 - Setting up the correct platform default values
31:37 - Calibrating the accelerometer
32:31 -- What is the accelerometer? And how do we know which way up the flight controller needs to be?
37:35 -- The calibration process
39:44 - Checking the movement on the setup page
41:26 - A quick overview of the mixer
42:18 - Pre-arming checks are ok, then so is the flight controller
43:11 Thinking about part layouts
48:06 Conclusion and what is in the next video

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 The iNav Configurator GitHub: github.com/iNavFlight/inav-configurator
🔗 ImpulseRC Driver Fixer: impulserc.com/pages/downloads
⚙️

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

Jumper T15 Transmitter: First look and unboxing

Mr.D - Falling with style 2024-10-13 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at the new T15 transmitter from Jumper RC. This is a mid size entry level transmitter that has a few nice features. Lets check it out.

✈️ Contents ✈️
00:00 Introduction
00:113 Costs and options
00:50 Unboxing
01:19 The transmitter case and accessories
02:12 How does the transmitter feel?
02:52 Transmitter basic layout - switches, buttons, trims, USB, and other stuff
05:12 The JR bay and how well do modules fit
06:02 Batteries
08:00 A quick power up and calibration
09:41 Plugging in the USB and the storage space available
10:33 A couple more features of note and observations
11:43 Initial thoughts on the transmitter
13:36 Taking the back off the radio
14:52 The back of the case and the ELRS module
15:51 Adjusting the gimbals and switching mode
17:15 The MCU, haptic motor, and speaker
17:48 The real time clock battery
18:03 The general quality of the internals
19:14 Conclusion

For openness, this transmitter was provided by Banggood for review.

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ Jumper T15 transmitter: bit.ly/MrD_JumperT15

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#JumperT15 #RCTransmitter

How to add custom OSD Elements in INAV

Mr.D - Falling with style 2024-08-25 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

A really useful addition to INAV 7 was the ability to add custom OSD elements. Using these, you could pretty much show any data you want on the OSD. There are some limits. The data needs to be accessible or created in the programming tab. But other than that, you can fill your boots.

In this video, I show an example of how you can simply get some flight data and show it on the OSD. My example shows how to add altitude in metres and distance from home in kilometres. You may think that those units are already available. Not if your OSD is in a non-metric configuration ;)

I also show an example of how to replicate the functionality of the current OSD switch indicators.

✈️ Contents ✈️
00:00 Introduction
01:10 Where are the custom OSD elements?
01:26 How do you enable the custom OSD elements?
02:42 Where do you set up what is shown on the OSD
03:10 Basics on customising the OSD element
05:50 How do you get the data to put on the custom OSD element?
06:00 Example 1: home distance in km and altitude in m
08:45 How this collates to the setup on the OSD page
09:02 Were do you find the number to use for icons?
11:45 Example 2: custom switch indicators
18:39 A note about some current limitations for some values
20:03 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 INAV Configurator GitHub: github.com/iNavFlight/inav-configurator

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#INAV #CustomOSD #INAV7

Caddx Walksnail Avatar GT: First look

Mr.D - Falling with style 2024-08-04 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at the new Caddx Walksnail Avatar GT VTX. This is Walksnails first VTX aimed at long range.

✈️ Contents ✈️
00:00 Introduction
00:31 Specs and differences to other kits
03:29 The MicroSD card setup
04:29 Antenna connections
05:17 Direct solder pad. Warning, these are not for power in!
06:05 Internal ceramic antennas
07:25 Installation and camera attachments
08:20 Camera and antennas
08:43 Wiring diagram
09:25 Unboxing
10:58 My installation overview
12:21 How I installed the VTX
13:43 A warning about the MicroSD card plastics
14:45 How is this setup for VTX heat?
15:57 A brief overview of the build of the AR Pro
17:20 Final thoughts, TL;DW, and Conclusion

In the video, I made a mistake. I thought that TCS FPV had made a video about why we shouldn't use mW with digital But, he hasn't. He has some interesting videos on antennas though, so you should check out his channel youtube.com/@tmc-fpv

Tom also runs the awesome https://walksnail.wiki/ web site. Which has lots of helpful information.

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ Walksnail Avatar GT kit: caddxfpv.com/products/walksnail-avatar-gt-kit

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#Walksnail #LongRange #FPV

INAV Public Service Announcement: Cant arm with plenty of satellites & 7.1.1 no baro issue

Mr.D - Falling with style 2024-07-14 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we look at a couple of issue that have come up quite a lot recently.

The first issue is not being able to arm. Even with a good satellite lock, with at least 6 3D fixes, and a low HDOP. A rogue parameter setting may be causing you this problem.

Next we look at the default parameter setting that caused the release of INAV 7.1.2. This setting would turn off the use of the barometer, when in most cases it should be enabled.

TL;DW: The CLI commands are
set inav_use_gps_no_baro = off
set inav_max_eph_epv = 1000

✈️ Contents ✈️
00:00 Introduction
00:18 Can't arm, even with lots of satellite locks and low HDOP
02:29 inav_use_gps_no_baro issue. Check even if on 7.1.2

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

Charger balance extension cable

Mr.D - Falling with style 2024-06-23 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

Here is a useful little cable from SpeedyBee. Which makes charging easier. In the days of old. Chargers used to come with long leads. Which meant plugging in the battery was pretty easy. These days, chargers are more minimalistic. The main power and balance ports are flush installed in the charger. It looks nice. But it can be a pain to plug in the battery. Especially when the battery has short balance leads.

In the past, we could have used regular balance extensions to make life a bit easier. But, you either had to force the balance lead in to the extension. Or cut down the socket on the extension to allow batteries of different cell counts to fit.

SpeedyBee have released some balance lead extensions that allow us to have an easier time. The sockets can accept 2S to 6S packs without any forcing or modification.

✈️ Contents ✈️
00:00 Introduction
00:24 How chargers used to look compared to now
00:45 Why are the flush balance ports a problem?
01:08 The answer to the problem
02:47 Any problems with these leads?
03:32 It's not needed for parallel charge boards. But here's why I stopped using them
04:08 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ SpeedyBee Balance Extension Cable: bit.ly/MrD_SpeedyBeeBalanceExtension

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

Caddx GOFILM 20 Unboxing and review

Mr.D - Falling with style 2024-04-28 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at the new @CADDXFPV GOFILM 20 cinewhoop. What do you get? How does it fly? Is it suitable for beginners? Plus much more.

✈️ Contents ✈️
00:00 Introduction
00:31 Unboxing
01:42 - In the box, basic accessories, and manual
04:12 - What batteries to get?
05:04 - The quad and what's on it
08:00 What are the defaults on BetaFlight?
09:13 - How to setup the barometer, if its not already working
10:34 - Default mode setup
11:17 - ELRS receiver target
12:32 - Receiver page setup
13:35 - Failsafe, and how to see if its working
15:15 - Motor setup
15:25 - Setting the battery details
16:15 7 weeks later...
16:56 Checking out the quad after weeks of abuse
17:08 Make sure to check the prop bolts are there and tight
18:49 Check your moonlight settings before flying
19:14 My biggest issue with the GOFILM 20
20:19 The update cable
20:31 MicroSD card removal
20:54 The video antennas
23:07 The ELRS antenna
23:15 A nice upgrade would be an Ummagrip battery pad
23:47 Overview of the settings I've been flying for testing
24:27 How does it fly on the stock tune?
25:32 Would I recommend the GOFILM 20?
25:43 Update on battery sizes
26:46 How much does this cost and is it reasonable?
28:26 Does it compare to the DJI Avata 2?
29:47 Would the GOFILM 20 be suitable for a beginner?
30:48 Conclusion

BetaFlight CLI for barometer and OSD
resource I2C_SCL 2 B10
resource I2C_SDA 2 B11
set baro_bustype = I2C
set baro_i2c_device = 2
set osd_canvas_width = 53
set osd_canvas_height = 20

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗
⚙️ Caddx GOFILM 20: caddxfpv.com/products/caddxfpv-gofilm-20

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#caddx #caddxfpv #gofilm20

Whats new in INAV 7.0 and 7.1? Find our now!

Mr.D - Falling with style 2024-04-07 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video, we check out the latest releases from INAV. Versions 7.0 and 7.1. Which was just released on the 1st of April. So what's new? Lets take a look.

✈️ Contents ✈️
00:00 Introduction
00:35 Where to download the latest version of INAV
01:19 How to update to INAV 7.1
01:58 - CLI Autocomplete now in INAV
04:36 Where to find the release notes
05:46 What's changed in INAV 7.0 and 7.1
06:26 - Flexible motor and servo allocation (mixer - resource remapping alternative)
09:37 - VTOL in INAV (tilt rotor, quad-plane, and tail sitter)
10:42 - Ez Tune - simpler tuning for multirotors
12:00 - In-flight emergency re-arming
15:25 - Timer DMA burst
15:51 - Jeti ExBUS protocol fixed and 24 channels available
16:06 - Cruise mode for multirotors
16:43 - NMEA protocol removed
17:12 - GNSS improvements - more constellations and faster communications
17:45 - MSP VTX support added
18:15 - Linear descent for RTH has changed
20:59 - Pilot logos added to INAV
23:41 - Smaller changes in INAV 7.0
25:41 - Odometer added to the OSD
26:27 Changes in INAV 7.1
26:43 - Multirotors no longer need to us a compass
27:48 - Fixed wing autoland
31:13 - Add your own custom OSD elements
33:22 - The artificial horizon tracks the real horizon when inverted
34:08 - New flight mode - Angle Hold
34:22 - Smaller changes in INAV 7.1
34:31 - You can now set a minimum ground speed
36:19 - The maximum number of LEDs have been increased to 128
36:33 - Add a delay before landing in a Failsafe
39:16 - Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 Download the latest configurator from: github.com/iNavFlight/inav-configurator/releases
🔗 INAV 7.0 Release Notes: Firmware | Configurator github.com/iNavFlight/inav-configurator/releases/tag/7.0.0
🔗 INAV 7.1 Release Notes: Firmware | Configurator github.com/iNavFlight/inav-configurator/releases/tag/7.1.0
🔗 INAV 7.0 Pull Requests (Firmware): github.com/iNavFlight/inav/pulls?q=is%3Amerged+is%3Apr+milestone%3A7.0+
🔗 INAV 7.1 Pull Requests (Firmware): github.com/iNavFlight/inav/pulls?q=is%3Amerged+is%3Apr+milestone%3A7.1+
🔗 INAV 7.0 Pull Requests (Configurator): github.com/iNavFlight/inav-configurator/pulls?q=is%3Amerged+is%3Apr+milestone%3A7.0+
🔗 INAV 7.1 Pull Requests (Configurator): github.com/iNavFlight/inav-configurator/pulls?q=is%3Amerged+is%3Apr+milestone%3A7.1+

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#inav7 #inav #fpv

Discover SpeedyBees Mario 5 Quad Frame: Best bang for the buck?

Mr.D - Falling with style 2024-03-03 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out the new Mario 5 frame from SpeedyBee. This is the DC (dead cat) version. But standard XH frame versions are also available. If you would like one, they're available here bit.ly/MrD_SpeedyBeeMario5

For transparency. This frame was provided by SpeedyBee for review.

✈️ Contents ✈️
00:00 Introduction
00:22 An overview of the different versions
01:20 Some specs on the frames
01:55 Unboxing
02:15 - Battery strap
02:44 - Checking out the standard components included
04:15 - What's in the advanced kit?
05:07 Some details and different options for the build
08:21 Building the frame
08:27 - The carbon parts
09:23 - Make sure to check the bolt sizes
09:50 - The capacitor area and a tip for holding on the arms
10:51 - Clear receiver cover and rear TPU piece
11:44 - The feet
12:11 - The FPV camera area
15:10 - XT60 and antenna holder, plus different options
16:16 - FC stack
16:33 - Bottom complete and pretty rigid
16:50 - Stack size and what capacitors will fit in the gap
18:05 - Top plate installation
18:27 Thoughts after completing the build
19:33 My plans for the build. What are your thoughts?
20:44 The price
22:13 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 SpeedyBee website: speedybee.com/speedybee-mario-5-frame
⚙️ Buy the SpeedyBee Mario 5: bit.ly/MrD_SpeedyBeeMario5

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#SpeedyBee #drone #quad

Caddx Walksnail Moonlight 4K Kit: First look and unboxing

Mr.D - Falling with style 2024-02-25 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at the new Caddx Walksnail Moonlight 4K Kit. What's it like? How does it perform? Lets find out.

✈️ Contents ✈️
00:00 Introduction
00:57 Product overview
02:14 Unboxing
02:24 Quick start guide
03:22 Accessory bags
04:14 Antennas
04:32 The Moonlight module
10:00 The camera and ND filter
12:31 A quick overview of my thoughts of the Moonlight 4K
13:37 The installation in my test plane
14:14 Overheating and how I resolved it
14:57 Thoughts about the installation
17:05 A note if you're planning to use this system with 3S LiIon packs
18:03 Best voltage to power the Moonlight 4K
18:20 Did I use the ND filter?
18:58 Some in flight footage using the Moonlight 4K. All using 4K 60.

In the spirit of transparency. This unit was provided by Walksnail for testing.

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ Caddx Walksnail Moonlight 4K Kit: bit.ly/MrD_WalksnailMoonlight4K

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#Walksnail #Moonlight4K

SpeedyBee F405 WING MINI: First look and unboxing

Mr.D - Falling with style 2024-02-18 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video, we check out the new SpeedyBee F405-WING Mini flight controller. This is a smaller version of the original SpeedyBee WING flight controller. Though it's smaller. It retains a lot of the features of it's larger sibling. It even has a few tricks the larger one doesn't have. Lets take a look.

You can buy one of these from bit.ly/MrD_SpeedyBee_F405WINGMINI

✈️ Contents ✈️
00:00 Introduction
01:01 General info from the manual
01:32 Different installation options
03:47 An overview of the flight controller
11:55 The USB extender board
13:34 The PDB board
14:49 Wiring diagram
15:04 The power flow on the PDB
15:40 Important information about the video voltage and considerations for current
16:27 Last parts of the manual including setup
16:55 Unboxing
17:56 Checking out the PDB
18:46 USB extender and wireless board
19:38 Looking at the flight controller
20:13 The accessories
20:42 Checking out the USB extender cable
21:44 Size comparison to the original SpeedyBee F405 WING APP flight controller
22:51 Cables that come with the accessories
23:37 Warning for pilots that want to use 2 FPV cameras and use connectors
24:43 Some advice if you're not confident soldering
26:27 The last accessory pack
26:56 Are the standoffs grounds?
27:52 Conclusion
28:00 One more thing. How does it look in a small aircraft?

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗
⚙️ SpeedyBee F405 WING MINI flight controller: bit.ly/MrD_SpeedyBee_F405WINGMINI

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#SpeedyBee #F405-WING #FlightContoller

Removing the Air Speed element from INAVs OSD

Mr.D - Falling with style 2024-02-11 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we learn how to remove the airspeed element from the OSD in INAV. But, also why you may want to keep it.

✈️ Contents ✈️
00:00 Introduction
00:29 The OSD page, and showing that Air Speed is not accessible
01:30 How to select the Pitot tube for airspeed, or none for disabled
02:01 How to remove the Air Speed from the OSD if you want to
02:35 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#INAV #AirSpeed

SpeedyBee Meteor LED kit: First look and unboxing

Mr.D - Falling with style 2024-01-28 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at the Meteor LED kit from SpeedyBee. This can be used as a standalone LED kit. Or you can hook it up to a UART on your flight controller. To give the flight controller SpeedyBee app compatibility via Wi-Fi or Bluetooth.

For clarity. The Meteor LED kit was provided by SpeedyBee for review.

✈️ Contents ✈️
00:00 Introduction
01:20 Some specs and information on the SpeedyBee Meteor
02:12 The different wiring options
04:05 Unboxing
06:27 Where to cut the LED strip if you need to
07:00 A look at the Meteor in the Bee35 frame
07:25 The module on the Meteor
08:14 Using the Meteor LED strip
09:45 Using the SpeedyBee app to control the LEDs
11:43 Using the SpeedyBee app to connect to the flight controller
12:30 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ Buy the SpeedyBee Meteor LED Kit: bit.ly/MrD_SpeedyBeeMeteorLED
🔗 SpeedyBee Meteor information: speedybee.com/speedybee-bee35-meteor-led

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#SpeedyBee #LEDStrip

Thanks and a general update

Mr.D - Falling with style 2024-01-20 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

Firstly, I wanted to thank everyone on social media who donated to me in the first couple of weeks in January. This was hugely unexpected, and quite overwhelming. But thank you very much. Especially to Nick Boylan who was sharing the links.

I also wanted to chat about my recent absence. Plus some things that are coming in the near future.

✈️ Contents ✈️
00:00 Thank you
02:25 Why I've been away
04:10 Coming soon

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

INAV Fixed Wing Scaled Throttle: How to get the correct values in your OSD

Mr.D - Falling with style 2024-01-07 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video, I show fixed wing pilots how to get your navigation throttles (auto launch, cruise, loiter, RTH, missions etc) showing correctly in INAV.

Here are the CLI commands:
set max_throttle = 2000
set throttle_idle = 0

✈️ Contents ✈️
00:00 Introduction

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 INAV Hardware In The Loop: youtu.be/EnMx1cFLy4I

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#INAV

INAV 7.0 GPS Page: Are your GNSS settings getting reset?

Mr.D - Falling with style 2023-12-31 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out the updated GPS page in INAV Configurator 7.0. This has been catching some people out. As if they select certain GNSS constellations. The are all getting reset. We take a look at that. Plus, have a brief revisit of setting up the GPS and what to look out for if you have problems.

✈️ Contents ✈️
00:00 Introduction
00:35 Update to the latest version of Configurator
02:00 What has changed on the GPS page
02:09 Replicating the problem that pilots are having
02:25 Why is this happening? What to do about it
05:40 Which protocol should you use?
06:10 Getting the right time and date from the clock
06:30 How to know if the GPS is working properly
09:14 Why can't I arm with 6 satellites?
09:48 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

Setting up telemetry and sensor widget screens on ETHOS

Mr.D - Falling with style 2023-12-17 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at how to add readouts for telemetry, channels, switches, and more on your home screen. Hell, you can even have multiple screens. This video comes in response from a viewer's question, asking how to display the aircraft voltage on the home screen. We look at how to do that and more.

✈️ Contents ✈️
00:00 Introduction
00:27 An overview of the telemetry screens and widgets
02:27 Changing a widget
04:35 Getting telemetry sensors from the receiver
06:06 Adding the receiver voltage to the home screen
06:38 Getting the battery voltage if the battery is not directly plugged in to the receiver
07:25 Making sure that the AIN2 pin can handle the voltage output of our battery
08:22 Making up a cable to attach the battery to the AIN2 plug
09:11 Setting the widget to use AIN2
09:42 Tuning the sensor to display the correct voltage
12:08 What if the values are red?
12:17 Changing layouts and adding multiple sensor widget screens
13:19 Adding a new screen layout
15:50 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #ETHOS #Telemetry

SpeedyBee Bee35 Pro frame First look

Mr.D - Falling with style 2023-12-03 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out the new SpeedyBee Bee35 Pro 3.5 inch cinewhoop frame.

✈️ Contents ✈️
00:00 Introduction
00:30 Checking out the prices on the web site
01:09 Unboxing
02:38 A closer look at the parts in the box
07:22 The built frame and my experience while building it
07:58 The one thing to watch out for in the build manual
10:20 Conclusion
11:16 One thing to consider if you're new to building quads

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ SpeedyBee Bee35 Pro frame: bit.ly/MrD_SpeedyBee_Bee35Pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#SpeedyBee #quad

RunCam Phoenix 2SP: First look and unboxing

Mr.D - Falling with style 2023-11-26 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at the RunCam Phoenix 2SP. We take a look at the specs and how the image of the camera looks. This is my first FPV camera review, so if you have any constructive criticism. Please feel free to leave it in the comments.

This FPV camera has been provided by Banggood.

✈️ Contents ✈️
00:00 Introduction
00:37 Unboxing
03:30 My test rig
05:01 The specs of the comparison camera
05:48 Comparing the image quality
06:45 - Flare tests
07:25 - Low light tests
09:50 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ RunCam Phoenix 2SP: bit.ly/MrC_RunCamPhoenix2SP

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

Understanding the different FrSKY Stabilised Receivers

Mr.D - Falling with style 2023-11-19 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out the different types of FrSKY stabilised receivers. Each type has a differences including the channel map, self test activation method, and the tools you use to configure them. I look at the current and historical stabilised receivers, and how each type is used.

This video doesn't go into depth about how to set up and calibrate the receivers. For more information on that. Check out these videos:

Archer Plus/TD SRx: youtu.be/gzc1VwEPfCE
Archer SRx: youtu.be/rUKIBQdmvIY
SxR: youtu.be/SQ-cpXhrL5A

✈️ Contents ✈️
00:00 Introduction
01:01 The different types of FrSKY stabilised receivers
04:54 The different channels used for the stabilisation functions
07:20 Which tools to use for the different types of receiver
09:46 Self check on the different types of receiver
11:25 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

Its here! INAV 7.0 RC1

Mr.D - Falling with style 2023-11-05 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at INAV 7.0 RC1, if you should install it, what you may need to do if you do install it.

✈️ Contents ✈️
00:00 Introduction
00:29 Should you use INAV 7.0 RC1?
01:23 Where can you find the information for RC1?
01:50 How do you download INAV 7.0 RC1?
02:44 If you do use Release Candidates, make sure you keep up to date
03:24 Where to find the release notes
03:59 What are the major changes in INAV 7?
11:45 Other changes to be aware of
14:50 Where to report issues if you find any
16:03 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 Releases and reporting issues video: youtu.be/Eul5BLyLoP0
🔗 INAV Firmware GitHub: github.com/iNavFlight/inav
🔗 INAV Configurator GitHub: github.com/iNavFlight/inav-configurator

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#INAV #INAV7.0 #INAV7.0RC1

Read out the battery voltage and other values on your ETHOS transmitter

Mr.D - Falling with style 2023-10-29 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we look at how to have your ETHOS transmitter read out values, for example the battery voltage. This can pretty much be any value on ETHOS, including all the telemetry sensors you have discovered. In the video, we take the battery voltage as an example. Showing how it can be read out from operating a switch. Or automatically read out when the value exceeds a specified target.

✈️ Contents ✈️
00:00 Introduction
00:31 Getting the telemetry sensors
02:37 Creating a special function to simply read out a value
04:01 Having the value automatically read out when a threshold is passed
07:25 Fixing the mistake in the BATT LOW logic switch
08:25 Having the value read out at a set interval
09:47 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #ETHOS #LogicSwitch

SpeedyBee 5.8GHz Video Receiver: First look

Mr.D - Falling with style 2023-10-22 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out the new 5.8GHz analogue video receiver from SpeedyBee. If you're interested in buying one of these receivers. They can be bought globally from bit.ly/MrD_SpeedyBee58VRx

✈️ Contents ✈️
00:00 Introduction
01:50 Unboxing
02:28 The supplied antennae
05:54 The 5.8GHz VRx module
07:27 Functions available on the module
09:39 My thoughts on missing features
11:22 Antennas on the VNA ...or not
11:52 Wrapping up

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗
⚙️ SpeedyBee 5.8GHz analogue video receiver: bit.ly/MrD_SpeedyBee58VRx

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#SpeedyBee #FPV

Using the multi function buttons with ETHOS: The modes and how to output on a single channel

Mr.D - Falling with style 2023-10-15 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out the multifunction buttons that are on all the latest FrSKY transmitters. On the X18, X20, and XE, there are 6 buttons at the bottom centre of the transmitter. On the TWIN X-Lite, there are 4 buttons, just below the screen. This video shows how this works on an X20. But it's the same on all the transmitters. With the X-Lite, you will have 4-pos, 4pos with off, 4 x 2 pos, and momentary modes. All the different button modes are explained. Plus, I show how to get 2x3 pos, 6-pos, and 6-pos with off modes operating on a single channel.

✈️ Contents ✈️
00:00 Introduction
00:35 Where to change how the multifunction button works
01:15 6-pos or 4-pos on the TWIN X-Lite
01:33 6-pos with off or 4-pos with off on the TWIN X-Lite
01:46 2 x 3 pos
02:17 6 x 2 pos or 4 x 2 pos on the TWIN X-Lite
02:48 Momentary
03:02 How to set up the switches that need additional programming
07:32 How to use the multifunction switch in addition to a traditional switch
11:56 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #ETHOS #ETHOSProgramming

Inside the FrSky TANDEM X20 Pro: Adjusting gimbals and changing mode

Mr.D - Falling with style 2023-10-08 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look inside the FrSky Tandem X20Pro transmitter. Not only can you find out how to take this radio apart. But we also look at the most performed tasks inside the radio. Including:
- Gimbal adjustment
- Swapping to mode 1, 3, or 4
- Rotating the gimbals
- Replacing the RTC battery

✈️ Contents ✈️
00:00 Introduction
01:03 About the back, and what parts you may need to remove
02:57 Changing the real time clock (RTC) battery
02:18 Rotating the gimbals
02:46 Information about the antenna configuration
04:01 Removal of the central part of the rear case (shown in reverse)
06:04 Adjusting the gimbals and changing mode
08:12 Removing the rear side panels (shown in reverse)
10:16 Make sure that the radio is still working OK after taking the back off
10:44 The changes in ETHOS needed to switch mode
11:36 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSky TANDEM X20Pro transmitter: bit.ly/MrD_FrSKYX20Pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSky #X20Pro

SpeedyBee F405 V4 55A Stack: Unboxing and first look

Mr.D - Falling with style 2023-09-29 | In this live broadcast, we check out the new SpeedyBee F405 V4 Stack. This is an update to the SpeedyBee F405 V3 stack, which really impressed me. I've been flying the V3 in my AOS 5, and it has been faultless. This update brings some nicer hardware, more power handling, and is still the same awesome price.

This is my first time trying a live unboxing. Did it totally suck, or is there some hope? What did you think? Leave me a comment and let me know.

The main differences between the V3 and V4 are:
Flight controller:
The V 3 has a BMI270 gyro, whereas the V4 now uses an ICM42688P. The V4 has an improved LDO power chip for the gyro with much better surge protection. The V4 can handle 3A on the 5v and 9v BECs, compared to 2A on the V3. The V4 has DSHOT support on INAV from the get go. V3 currently doesn't work with DSHOT on INAV. But an update in INAV 7 will get this working. The SD card reader chip is better quality and more reliable.

ESC:
Continuous current is now 55A, up from 50A. The burst current is now 70A, up from 55A. The copper traces are thicker. There is now an aluminium heatsink. The MOSFETs have a lower internal resistance, and there are more filtering capacitors. The V4 is about 10g heavier than the V3; about half of this increase is due to the heat sink.

This new stack can be found at speedybee.com/speedybee-f405-v4-bls-55a-30x30-fc-esc-stack

Contents
00:00 Waiting screen (skip this)
06:27 Introduction
07:42 Unboxing
08:00 - The 55A 4-in1 ESC
10:08 - The flight controller
14:39 About DSHOT on INAV, and how it will work with the v3 in INAV 7.0
15:55 - The accessories
20:25 Pinouts on the flight controller
24:44 Conclusion

If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

There are more tutorials on my web site at https://www.MrD-RC.com. You can also join like-minded people at the Fixed Wing RC Rebels group on Facebook. Also, if you found my videos useful, and would like to leave me a little tip, you could always buy me a Coffee at mrd-rc.com/go/ko-fi

Thank you for your time, and don't forget to fly it like you stole it!

#SpeedyBee #F405 #FPV

A better hands free climb/descent for INAV, ArduPilot, and other flight controller firmware

Mr.D - Falling with style 2023-09-24 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video, we revisit a nice addition to your transmitter model. This will allow you to climb or descend as a set rate. I have shown you how to do this before. But this new version is much better. Now you can enable and disable your climb or descent without needing to change the rate. There are also nice automated entries and exits for this assistance feature.

✈️ Contents ✈️
00:00 Introduction
01:16 How the old version worked, and how the new version will work
02:08 How I have the basic models setup on the transmitters
02:47 Step 1 - Disable the trims (OpenTX/EdgeTX)
03:35 Step 1 - Disable the trims (ETHOS)
04:15 Step 2 - Adding the pot and curve for the hands free climb/descent (ETHOS)
07:07 Step 2 - Adding the pot and curve (OpenTX/EdgeTX)
09:33 Step 3 - Setting up the logic and assigning it to the mix (OpenTX/EdgeTX)
10:15 - Logic for detecting the flight modes
12:12 - Logic to activate the hands free climb/descent
14:45 - Logic to deactivate hands free climb/descent
16:25 - Latching switch for hands free climb/descent enabled
17:35 - Setting up the switching in the mixer
17:58 - Demo of the system working
19:00 Step 3 - Setting up the logic and assigning it to the mix (ETHOS)
19:02 - Logic for detecting the flight modes
21:40 - Logic to activate the hands free climb/descent
23:55 - Logic to deactivate hands free climb/descent
25:59 ETHOS comments and how they can be really useful
27:09 - Latching switch for hands free climb/descent and the OR for activating
29:25 - Setting up the switching in the mixer
29:50 - Demo of the system working
30:50 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSky TANDEM X20 Pro transmitter: bit.ly/MrD_FrSKYX20Pro
⚙️ FrSky Horus X10S Express transmitter: bit.ly/MrD_3l7b8K5

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#INAV #AutoClimb #OpenTX #EdgeTX #FrSkyETHOS

Moving models and more between two ETHOS transmitters

Mr.D - Falling with style 2023-09-17 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out how to transfer modes, audio, LUA, and bitmaps between ETHOS transmitters. This is particularly useful if you have changed or upgraded transmitters. The moving process is pretty simple. But make sure that your moved models work as expected before flying. Especially if moving between transmitters that have different switches and buttons. You will likely need to re-register and re-bind your receivers.

✈️ Contents ✈️
00:00 Introduction
00:10 Step 1 - Make sure the firmware version matches
01:17 Step 2 - Find out where things are stored on each transmitter
01:43 Step 3 - Transferring the files via your computer
02:52 Selecting the correct to and from drives
04:42 Copying the models
05:22 Copying other files, like logs, model images, and audio
08:53 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 Updating ETHOS using ETHOS Suite: youtube.com/watch?v=fvxbYacd-bk&t=382s
⚙️ FrSKY TANDEM X20S: bit.ly/MrD_3x6n6JL
⚙️ FrSKY TANDEM X20Pro: bit.ly/MrD_FrSKYX20Pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #MoveModels #ETHOS

FrSKY X20 Pro : First look and unboxing

Mr.D - Falling with style 2023-09-10 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video, we check out the new flagship transmitter from FrSKY. The TANDEM X20 Pro. This is a radio that has been talked about for some time. Now it's finally here, and we can take a look at it in the flesh. The X20Pro is available now. Though you may have a wait if you want to buy one. Due to the CNC machined body, there is already a waiting list for this transmitter. Only 4 of the aluminium bodies can be produced a day, meaning 20 radios per week. In the video, we will take a general look at the radio, see how it compares to the original X20, and also chat about that price tag.

If you're interested in this transmitter. It can be purchased globally from bit.ly/MrD_FrSKYX20Pro

TL;DW This is a high quality, premium radio. Every switch and dial feels like it will last decades; and has a reassuring click, pressure, or centre detent. Everyone that I have shown the X20 Pro to has commented on how great the switches feel, and the general excellence of the build.

✈️ Contents ✈️
00:00 Introduction
00:52 How much does it cost?
01:06 Unboxing: The case
01:31 - Included accessories
04:23 Comparing the X20S and the X20Pro
06:38 How much does the X20Pro weigh?
07:19 The X20Pro hardware
10:19 Ports, module bay, and battery
11:20 The CNC machined aluminium case
11:36 A quick look at ETHOS
12:08 Text to speech
13:39 Calibrating the gimbals, pots, and sliders
14:58 Setting the date and time
15:50 The three different RF systems available on the internal ISRM module
19:23 IMPORTANT: Check your firmware version before using the transmitter in flight
19:55 Updating ETHOS
21:21 The different file areas on the X20 Pro
24:06 If you still have the bootloader screen after updating
24:40 General thoughts on the X20 Pro
26:15 Is the X20 Pro worth the extra cost?
29:50 Conclusion and upcoming videos

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 FrSKY ETHOS Feedback Community: github.com/FrSkyRC/ETHOS-Feedback-Community
⚙️ FrSKY TANDEM X20Pro transmitter: bit.ly/MrD_FrSKYX20Pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #X20Pro

RadioMaster Zorro LE : First look and unboxing

Mr.D - Falling with style 2023-09-03 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out the Limited Edition RadioMaster Zorro transmitter. This is a small, gamepad style transmitter. This type of transmitter is ideal for flying quads, or for transporting in a backpack. How does the Zorro stack up? Lets take a look.

The Zorro LE is available from Banggood here bit.ly/MrD_RadioMasterZorroLE

✈️ Contents ✈️
00:00 Introduction
00:25 What's in the box
02:22 Checking out the radio
06:36 Setting the clock
06:52 Calibrating the gimbals and sliders
09:21 The external antenna
10:04 The little plastic doors
10:28 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ RadioMaster Zorro Limited Edition: bit.ly/MrD_RadioMasterZorroLE

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

Updating FrSKY RB firmware and installing the ETHOS LUA script RB25 RB25S RB35 RB35S

Mr.D - Falling with style 2023-08-20 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video, we look at how to update the RB25, RB25S, RB35, or RB35S. We go through all the steps, from downloading the firmware, software, and scripts. To installing them on your RB device and ETHOS transmitter. Currently, prerequisites for installing this firmware on your RB device is the STK Tool. There is a link to the tool below.

✈️ Contents ✈️
00:00 Introduction
00:48 Downloading the firmware for the RB device, ETHOS LUA scripts, and the STK software
02:34 Installing the Windows driver for the STK adapter, if you need it
03:20 Extracting the STK update tool
03:34 Extracting the RB firmware to the desktop
03:52 Preparing the RB device for update
05:16 Flashing the RB device with the new firmware
06:50 Installing the RB device LUA scripts on your transmitter
06:58 Where to install the LUA scripts
07:42 Connect the transmitter to your computer
07:49 Copying the files to the correct drive on your transmitter
09:48 Locating the RB LUA tools on the transmitter
10:38 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 FrSKY website:
⚙️ FrSKY Tandem X18 transmitter: bit.ly/MrD_3LD7R1j
⚙️ FrSKY RB35S: bit.ly/MrD_FrSKYRB35S
⚙️ FrSKY STK tool: bit.ly/MrD_FrSKYSTK

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #RB25 #RB35

SonicModell Baby AR Wing Pro Build, Maiden, and Review

Mr.D - Falling with style 2023-08-13 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we finally get to maiden the @SonicModellOfficial Baby AR Wing Pro. Before we do, I take a quick look at my build and the good and bad points. Then we see how this thing flies. How good is it? Watch and find out 😉

The Baby AR Wing Pro is available from Banggood here mrd-rc.com/go/sonicmodell-baby-ar-wing-pro

✈️ Contents ✈️
00:00 Introduction
00:17 The build process and how I built mine
05:15 Caution if you want to remove the wings
06:20 The flight controller setup
07:11 Time to fly!! ...and my mistake
08:43 Changes due to the ESC dying and burning out the motor
10:21 The real maiden flight
12:20 How does the Baby AR Wing Pro stall?
16:40 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ SonicModell Baby AR Wing Pro: mrd-rc.com/go/sonicmodell-baby-ar-wing-pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#SonicModell #BabyARWingPro #ARPro

SonicModell Baby AR Wing Pro maiden and review, this afternoon! #fpv #inav #BabyARWingPro

Mr.D - Falling with style 2023-08-13 | Check out more about the Baby AR Wing Pro youtu.be/Cn_AJR5D65A

HD FPV: Why DJI ARE the bad guys

Mr.D - Falling with style 2023-08-02 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

This is a bit of a different video for me. It's not really a tutorial or review. But more just passing along some information to dispel some mistruths that are going around. In particular, this video comes as a result of seeing some of the comment's in Mads Tech's (@MadRC) video "DJI Goggles 2 & O3 FPV Do Not Buy - They Just Don't Care" (youtu.be/r72p6bI63Dg). In this video, Ian makes a lot of harsh, but fair comments about DJI, and this whole mess with their firmware.

One guys' comments in particular caught my eye, stating: "INAV devs CAN fix this, but they are stubborn and just won't bother. Why not blame the INAV devs?" and "Yeah, INAV devs can fix this, but they want drama in the community." Other than the INAV developers and community being the least likely to cause "drama". The INAV community is genuinely one of the most helpful I've been involved with. It is showing that some people don't actually know what's going on here.

The INAV devs did a lot of work to get even a basic level of OSD for O3 pilots. Something that they should not have even needed to do, if DJI had done things properly.

Hopefully this video will go some way to show exactly what the problem is. Why it is 100% DJIs fault, how INAV devs are actually going above and beyond to support O3 pilots, and why the font is so important. TL;DR, it isn't just about the characters looking different!

✈️ Contents ✈️
00:00 Introduction
01:46 All about MSP DisplayPort and why this isn't the problem
04:43 The differences between the font sets
05:21 Comparing with BetaFlight's base font
06:20 Comparing with ArduPilot and INAV
08:30 Is INAV just causing drama?
09:14 What is the real fix, and why DJI are the only people who can do it
09:53 Why you shouldn't by DJI!
11:03 Why don't BetaFlight pilots understand the issue fully?
12:30 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 Mads Tech Channel: youtube.com/@MadRC

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#DJI #HDFPV #DontBuyDJI

FrSKY ETHOS: Using a linear control as a switch - using the red slider for throttle cut

Mr.D - Falling with style 2023-07-30 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

This video is to answer a question I received from a viewer on how to use the red slider for throttle cut. This technique can be used to turn any linear control (slider or pot) in to a switch. So it could be used for a multitude of tasks.

✈️ Contents ✈️
00:00 Introduction
01:08 Creating the Logic Switch
03:07 Assigning the Logic Switch to the throttle cut
03:50 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY TANDEM X20S Transmitter: bit.ly/MrD_3x6n6JL

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #ETHOS #LogicSwitch

Re-arming in flight with INAV

Mr.D - Falling with style 2023-07-23 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at what you should do if you accidentally disarm in flight, when flying with INAV. I have seen posts and messages from quite a few people who don't know what to do, and have lost models because of this. So I thought I'd make a quick video to show that it is possible to re-arm in flight. Not only that; it's actually pretty easy. TL;DW, Stay calm, get rid of the stats screen, and check for blocking messages on the system messages.

✈️ Contents ✈️
00:00 Introduction
00:30 Re-arm in flight without any restrictions
00:47 Why can't you just re-arm?
01:00 - Modes that will or won't let you arm
01:59 - Throttle position
02:09 - Autolaunch permanently enabled?
02:54 Having a fly, disarming, and recovering
07:29 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 Immediate re-arm in flight video: youtu.be/ndxtVzC7LHA
🔗 How to use the HITL: youtu.be/EnMx1cFLy4I

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

Setting up and flying Waypoint Missions in INAV

Mr.D - Falling with style 2023-07-16 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at how to set up a basic waypoint mission in INAV. I'm using version 6.1.1. so some of the options may not be available on older version. We look at:
- The mode you need to fly a waypoint mission
- What settings are available on the Advanced Tuning page
- How to set up a basic mission in Mission Control
- Flying the mission
This should give you all the information you need to know to setup and fly your first INAV mission.

NOTE: Please do not fly a mission before making sure that your aircraft is fully set up and correctly tuned. You should be 100% confident that the aircraft can fly safely and reliably in both standard and navigational flight modes. For example, if RTH is not smooth and predictable. Do not fly a mission until is it setup and tuned correctly, so that it is.

✈️ Contents ✈️
00:00 Introduction
00:21 What do you need on the transmitter?
00:41 How I'm demonstrating this
00:56 Adding the NAV WP mode
01:17 The Waypoint Navigation settings on the Advanced Tuning page
02:11 - Waypoint Radius
02:47 - Waypoint Safe Distance
03:22 - Load Waypoint on Boot
03:43 - Enforce Altitude at Waypoint
04:40 - Waypoint Tracking Accuracy
05:07 - Waypoint Tracking Angle
05:42 - Waypoint Turn Smoothing
06:28 - Restart Waypoint Mission
07:09 Planning the mission in Mission Control
07:39 - Set the first waypoint within the Waypoint Safe Distance from your arming position
08:06 - Moving the map and markers
08:20 - Creating a basic mission
09:20 - Setting waypoint options
09:48 - Getting the approximate ground elevation data and how to stay above it
11:00 - Speed
11:30 - Waypoint types and setting RTH on the last waypoint
12:08 - Saving and checking the mission
13:09 Flying the mission
14:07 - The indicator for NAV WP mode
14:19 - Indicators for the next waypoints
17:20 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 INAV Stick commands: mrd-rc.com/tutorials-tools-and-testing/inav-flight/inav-stick-commands-for-all-transmitter-modes
⚙️ FrSKY TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#INAV #WaypointMissions

How to use your own logo on the top of the ETHOS screen

Mr.D - Falling with style 2023-07-02 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video, we look at how to put your logo at the top of the ETHOS screen. The process it's self is pretty simple. But there is one key step that you must do, to have your logo appear.

✈️ Contents ✈️
00:00 Introduction
00:25 Which logo are we changing?
01:00 How to get to the file we need to change
02:42 What people usually try to get this working
03:50 How to upload the logo and have it actually change
05:12 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #ETHOS

Want to know my thoughts on Remote ID? Check out CurryKitten’s video. He nailed it!

Mr.D - Falling with style 2023-07-01 | If you want to know my thoughts on what the FAA are doing in the states and the whole Remote ID calamity. Please check out @CurryKitten’s recent video. I 1000000% agree with what he says in the video. So please watch it and share it extensively.

If the UK government are thinking of introducing such measures. Then they really at a gaggle of morons too! Stop it! It’s stupid!

youtu.be/4mkjiVbk5w8

#SayNoToRemoteID

How to fix configuring the Archer Plus stabilised receivers: Installing the FrSKY SRX LUA scripts

Mr.D - Falling with style 2023-06-25 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

A few people have contacted me, having problems configuring Archer Plus stabilised receivers, such as the SR10+. The SXR Tool no longer works for these receivers, and changes revert back to their old stated. The solution is to install new SRX LUA script tools These add new calibration and setup tools for the Archer Plus stabilised receivers. These new tools will be included as part of ETHOS 1.5. But, until then. We need to install them ourselves.

In this video, we have a quick overview of making sure everything is up to date. For full videos on updating, please see the links below. After that, we download and install the LUA script tools. Next, we have a quick look at the tool. If you have used the old SxR Tool. The new SR tool is very familiar. Only some of the names have changed to make things clearer.

✈️ Contents ✈️
00:00 Introduction
00:35 Make sure the transmitter operating system firmware (ETHOS) is up to date
03:15 Updating the RF or receiver firmware
03:47 Where can you find the versions of the RF and receiver firmware installed?
04:08 Downloading the firmware to the transmitter
04:55 Downloading the RF module from the FrSKY site
05:08 Downloading the receiver firmware from the FrSKY site
07:03 Updating the internal RF module firmware
08:19 Updating the receiver firmware
10:49 Downloading and installing the SRX LUA script
13:12 Where is the new SRX setup tools?
13:43 Checking out the new SRX configuration tool
17:18 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 Updating ETHOS: youtube.com/watch?v=fvxbYacd-bk&t=382s
🔗 Updating the transmitter's RF module: youtu.be/3DmDUWopO-0
🔗 Updating receiver firmware: youtu.be/9tncdNDinFM
⚙️ FrSKY TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL
⚙️ FrSKY Archer Plus SR10+ receiver: bit.ly/MrD_FrSkySR10Plus

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #SR10 #LUA

My little plywood demo plane: is it available?

Mr.D - Falling with style 2023-06-23 | ...

First look at the SonicModell Baby AR Wing Pro

Mr.D - Falling with style 2023-06-18 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a first look at the new SonicModell Baby AR Wing Pro. I have been sent the PnP version for review, so lets take a look at what we get. What are my thoughts about the model. Is this a real replacement for the Mini AR Wing?

This was supplied to me for review from Banggood. If you would like to buy it from them. This discount code will get you some money off. It will work until 30/06/2023.

The Baby AR Wing Pro is available from Banggood here: mrd-rc.com/go/sonicmodell-baby-ar-wing-pro
Code: BG3745a2

✈️ Contents ✈️
00:00 Introduction
00:46 Unboxing
01:08 Stickers and the instructions
02:04 Specs
04:27 Carbon spar, accessory pack, and prop
05:12 The wings
07:39 Winglets
08:06 The body, ESC and motor
09:17 Comparing the Mini AR Wing motor with the Baby AR Wing Pro
10:01 A quick build and checking out the battery space
12:16 The space for the FPV camera
12:30 airflow not optimal
12:54 Comparing the size of the Mini AR Wing and the Baby AR Wing Pro
13:14 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ SonicModell Baby AR Wing Pro: mrd-rc.com/go/sonicmodell-baby-ar-wing-pro

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#SonicModell #BabyARWingPro #BabyARPro

First look at the FrSKY RB35S Flight Safe System

Mr.D - Falling with style 2023-06-11 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at the FrSKY RB35S. This is a part of FrSKY's Flight Safe group of products. Designed to keep your model in the air and in control. In this video we look at what the RB35S is, what it does, and what you get with it. In coming videos, we'll check out flashing and setting it up. Also, there will be a video on the stabilisation system.

✈️ Contents ✈️
00:00 Introduction
00:43 What is Redundancy Bus?
03:36 Unboxing the RB35S
05:06 Size and weight of the RB35S
05:45 Overview of the RB35S
05:48 Power input redundancy
06:05 Connections on the side
06:15 The power outputs and BEC explanation
06:51 The PWM outputs
07:20 The Receiver and LED ports
08:44 Feature overview
10:47 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY RB35S: bit.ly/MrD_FrSKYRB35S

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY

INAV News: Dolphining in navigation modes in INAV 6.1

Mr.D - Falling with style 2023-06-06 | ...

How to calibrate gimbals, pots, and sliders in ETHOS

Mr.D - Falling with style 2023-05-28 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we discover how to calibrate gimbals, pots, and sliders in FrSKY ETHOS.

✈️ Contents ✈️
00:00 Introduction
00:14 Where is the calibration tool?
00:34 Centring all the sliders, pots, and gimbals
01:20 Performing the calibration
02:43 Testing the calibration
03:10 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY TWIN X-Lite: bit.ly/MrD_TWINXLite

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #CalibrateGimbals #FrSKYETHOS

Downgrading Walksnail Avatar firmware

Mr.D - Falling with style 2023-05-21 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we look at how to downgrade the firmware on the Caddx Walksnail Avatar FPV HD video system. Where to download the old firmware? How can you make it overwrite more recent firmware? Will it stop you updating to new firmware in the future?

✈️ Contents ✈️
00:00 Introduction
00:36 Where do we download the older firmware from?
01:08 Why can't we just use the standard old firmware file?
01:33 Downloading the firmware
01:51 Renaming the downloaded image files
02:50 Flashing the old firmware to the goggles
05:26 Checking the newly flashed firmware number
05:54 Will renaming the firmware stop you from updating to the next firmware?
07:09 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 Where to download the firmware: avatar-firmware.d3vl.com
⚙️ Avatar system (Goggles, VTx, and Camera): bit.ly/MrD_WSAV_Goggles_ProCam
⚙️ Avatar VTx & Pro Camera: bit.ly/MrD_WSAvatar_ProKit
⚙️ Avatar VTx & V2 Camera: bit.ly/MrD_WSAvatar_V2Kit

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#Walksnail #Caddx #downgrading #WalksnailWiki

Working with Profiles in INAV: Using different batteries or PIDs

Mr.D - Falling with style 2023-05-14 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we look at how to work with profiles in INAV. There are two types of profile: control profiles and battery profiles. These can be used to change settings based on the battery you plug in, a switch position, or manually set via stick commands. You can even change control profiles based on data from your flight controller via the programming tab. For example having different control profile based on your speed.

Most people will likely only need the battery profiles. Chances are that you may want to fly with different chemistry batteries, different capacity batteries, or different cell counts. If so, using the battery profiles is the best way to set this up.

✈️ Contents ✈️
00:00 Introduction
00:24 What are profiles?
01:02 How can you tell which settings are part of a profile?
01:24 Setting up the first battery
01:50 How to set up the profile for a second battery
02:51 Copying base changes from our main profile (1) to a new profile
07:04 Switching battery profiles automatically based on cell count
07:24 Finding the document for battery settings on GitHub
09:25 Changing control profile automatically, based on your battery profile
11:54 Finding the document for control profiles on GitHub
12:14 Changing control profiles with a switch
13:10 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 Battery document: github.com/iNavFlight/inav/blob/master/docs/Battery.md
🔗 Control profile document: github.com/iNavFlight/inav/blob/master/docs/Profiles.md

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#INAV #batteryprofiles

Organising your models in ETHOS

Mr.D - Falling with style 2023-05-07 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we take a look at how to organise models in ETHOS. We check out how to make new model categories. Also how to move existing models.

✈️ Contents ✈️
00:00 Introduction
00:30 Creating a new category for your models
01:14 Creating a new model within a category
01:29 Moving a model to a different category
02:19 How to delete a category
03:34 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY TWIN X Lite transmitter: bit.ly/MrD_TWINXLite

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSky #ETHOS

First look at the SpeedyBee F405 WING flight controller

Mr.D - Falling with style 2023-04-30 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we check out the new SpeedyBee F405 WING flight controller. At the time of purchase, this flight controller was only $39.99 (about £33). Which is an absolute bargain. Unfortunately, there are a few silly things to be aware of. What are my thoughts? Lets take a look.

✈️ Contents ✈️
00:00 Introduction
00:17 Opening up the box
00:32 Included MicroSD card
00:58 The paper manual
02:42 The accessories
04:28 - Remote USB Type-C board
05:16 The Power Distribution Board
05:40 - Switching the VTx and Camera voltage
06:14 - Changing the servo voltage
06:27 - The amp specs for the PDB
07:02 The Flight Controller board
07:10 - Signal out for the motors and servos
07:49 - Connecting a receiver
09:57 - Airspeed sensor connections
11:22 - The front connections
14:18 - The unfortunate position of the MicroSD card slot
16:33 The Wireless top board
16:41 - LED connectors
17:25 - Power indicator LEDs
17:55 - The wireless parts
18:25 The assembled flight controller
19:19 Potential problems when using the solder pads. Another reason to lose the connectors
20:34 The not so remote, remote USB adapter
21:43 First thoughts on the flight controller
22:27 This board is an F411 killer!
23:36 Size comparison between the SpeedyBee F405 WING and the MATEKSYS F405-WING and F765-WSE
25:18 The cool logo, which is also the flight controller forward direction arrow
25:31 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ SpeedyBee F405 WING: bit.ly/MrD_SpeedyBeeF405WING

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#speedybee #flightcontroller

How to record log files with ETHOS

Mr.D - Falling with style 2023-04-23 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

In this video we look at how to record log files on your ETHOS transmitter. I show two recording methods. One records all the time. The other only records when your throttle or arm switch is active. There's no use recording log files if you don't know how to find them. So I also show where they are on the transmitter; and how to access them on your PC.

✈️ Contents ✈️
00:00 Introduction
00:21 How the model is currently set up
00:53 How to set up logs to record all the time
01:20 The logging settings
02:31 How to set up the logs to only record when the throttle is active
03:02 How to access the log files on the radio
03:42 Accessing the logs on your computer
07:39 What can you do with the log files?
08:07 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
⚙️ FrSKY TANDEM X20S Transmitter: bit.ly/MrD_3x6n6JL

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#FrSKY #ETHOS #LogFiles

Why is INAV stuck in Manual mode?

Mr.D - Falling with style 2023-04-16 | 🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC

A few people have had a problem recently where INAV is stuck in Manual on the modes page. Fortunately, this is a really easy problem to fix. I show you how in this video.

✈️ Contents ✈️
00:00 Introduction
00:48 Why is INAV stuck in manual, and how to fix it.
01:50 Conclusion

Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer. Please try to keep questions relevant to the video in, as they may also help others who have the same question.

✈️ In this video ✈️
🔗 How to calibrate the accelerometer: youtu.be/1f_G0hKOUoQ?t=1897
⚙️ FrSKY TANDEM X20S transmitter: bit.ly/MrD_3x6n6JL

✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.

✈️ Supporting me and other resources ✈️
🛩 There are more tutorials on my web site at https://www.MrD-RC.com.
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su

🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you found my video useful, you can become a Patreon at patreon.com/MrD_RC
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.

Thank you for your time, and don't forget to fly it like you stole it!

#INAV #manualmode