How to Replace the Blade on a Lawn Mower @searspartsdirect
How to Replace the Blade on a Lawn Mower  @searspartsdirect
Uploaded August 2018 | Updated November 2026, 2 hours ago
Use promo code YOUTUBE to save 10% on searspartsdirect.com.

This video from Sears PartsDirect shows how to replace a blade on a lawn mower. It’s important to keep a sharp blade in order to keep your mower cutting evenly and cleanly. Check the mower blade a few times during the mowing season. If the blade is bent or damaged, you can replace it using the steps in this video.

(0:00) Introduction
(0:26) Step 1: Disconnect the spark plug wire
(0:29) Step 2: Remove the blade
(1:03) Step 3: Install the new blade
(1:29) Step 4: Reconnect the spark plug wire

Visit us at:
searspartsdirect.com/diy/repair-guide/how-to-replace-a-lawn-mower-blade?sid=soc:youtube:may-sem-replacing-the-blade-on-a-lawn-mower

Or call 1-800-437-1673 to speak with a parts specialist.

The video includes these parts. Look up your model to make sure you get the right parts for your lawn mower.
Blade
searspartsdirect.com/part-number/942-0741A/0071/247.html?sid=soc:youtube:may-sem-direct-part-link

Find parts for your lawn mower at:
searspartsdirect.com/partsdirect/product-types/Walk-behind-lawn-mower-Parts?sid=soc:youtube:may-sem-lawn-mower-parts

Or click here to schedule an appointment with a repair technician. searshomeservices.com/repair#showall

Transcript:
It’s important to keep a sharp blade in order to keep your mower cutting evenly and cleanly. Check the mower blade a few times during the mowing season. If the blade is bent or damaged, you can replace it using the steps in this video. Let the engine cool. Wear work gloves to protect your hands. Now, let’s get started. Disconnect the spark plug wire from the spark plug. Remove the fuel tank cap. Place a plastic bag over the fuel tank opening and reinstall the fuel tank cap to prevent gasoline from leaking out through the fuel tank cap vent. Tilt the mower back to lift the front wheels then secure the mower handle to your worktable to hold the mower steady. Wedge a block of wood between the mower blade and the deck to keep the blade from turning when you loosen the blade bolt. Loosen and unthread the blade bolt while holding the cutting blade to keep it from falling. Pull the blade, blade support and blade bolt off the crankshaft. Position the new blade, blade support and blade bolt on the crankshaft and hand-tighten the blade bolt into the crankshaft. Wedge a block of wood between the mower blade and the deck. Use a torque wrench to tighten the blade bolt. Remove the wood block from the cutting blade. Release the mower handle from the worktable and tilt the mower upright. Remove the plastic bag from the fuel tank opening and reinstall the fuel tank cap. Reconnect the spark plug wire to the spark plug.
How to Replace the Blade on a Lawn MowerHow to Remove Control Parts and the Lid Switch from a Maytag Atlantis III WasherHow to Replace the Axle Seal on a Riding Mower with a CVT RS800 TransmissionFront-Load #washer #tumbling #action illustrated3 Cabinet Cleaning Hacks   Tested!How to Replace a Common Dryer Heating ElementHow to Organize Your RefrigeratorKenmore 587 Series and Frigidaire Dishwashers - Dishrack Roller ReplacementHow to Fix a Riding Lawn Mower That Wont Start: Engine Clicks But Doesnt CrankKenmore 587 Series and Frigidaire Dishwashers - Dishrack Track Roller ReplacementHow to Replace a Broken Brake Lever on the RS800 CVT Transaxle of a Riding MowerHow to replace a side-by-side refrigerator press-in door gasket
Sears PartsDirect |

How to Replace the Blade on a Lawn Mower

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER