Uploaded November 2020 | Updated November 2026, 3 hours ago
Today we’re going to show you how to replace a refrigerator door gasket that presses into a groove around the edge of the door on a side-by-side refrigerator. The door gasket seals the gap around the door to keep the cold air in. You might need to replace it if you notice excessive frost buildup and reduced cooling, or if the gasket is worn, cracked or torn.
This repair procedure can be used on many Kenmore, Frigidaire, LG and Samsung refrigerators.
To smooth creases and folds in the gasket, carefully warm it with a hair dryer or heat gun on a low setting. Be careful not to melt the gasket. You can also soak it in warm water.
Replace the gasket:
1. First, unplug the refrigerator or shut off the circuit breaker for the refrigerator.
2. Pull the gasket out of the track, starting at one of the corners. You may need to tug the gasket firmly to get it started. If you have difficulty, try pulling the gasket out starting in a spot halfway down the side of the door. Once you get the removal process started, you should be able to pull the gasket out fairly easily.
3. Clean the track in the refrigerator door.
4. Using a wet cloth, wipe any spills from inside and around the track to ensure that the new gasket fits easily in the track and seals the door properly.
5. Install the new gasket.
6. Starting at the top of the door, work the new door gasket into the track. Work your way down both sides of the door and across the bottom.
7. Check for loose spots and adjust the gasket as needed for a proper fit.
8. Spread a thin coat of petroleum jelly along the sealing surface of the door gasket to help the new gasket seal properly.
9. Close the door and check the fit. The door gasket should fit tightly against the cabinet and door with no gaps showing. Smooth out any creases that cause gaps. Push the door gasket further into the track to eliminate gaps.
10. Turn the refrigerator back on or restore power to the refrigerator.
11. Use the same procedure to replace the freezer door gasket.
We hope this video helped you out today. Please subscribe to our channel to see more repair tips and tricks.
For more DIY help, visit
searspartsdirect.com/diy/repair-help?sid=soc:youtube:DIY
Find parts for your refrigerator at
searspartsdirect.com/category/1234589/refrigerator-parts?sid=soc:youtube:refrigerator-parts
Today we’re going to show you how to replace a refrigerator door gasket that presses into a groove around the edge of the door on a side-by-side refrigerator. The door gasket seals the gap around the door to keep the cold air in. You might need to replace it if you notice excessive frost buildup and reduced cooling, or if the gasket is worn, cracked or torn.
This repair procedure can be used on many Kenmore, Frigidaire, LG and Samsung refrigerators.
To smooth creases and folds in the gasket, carefully warm it with a hair dryer or heat gun on a low setting. Be careful not to melt the gasket. You can also soak it in warm water.
Replace the gasket:
1. First, unplug the refrigerator or shut off the circuit breaker for the refrigerator.
2. Pull the gasket out of the track, starting at one of the corners. You may need to tug the gasket firmly to get it started. If you have difficulty, try pulling the gasket out starting in a spot halfway down the side of the door. Once you get the removal process started, you should be able to pull the gasket out fairly easily.
3. Clean the track in the refrigerator door.
4. Using a wet cloth, wipe any spills from inside and around the track to ensure that the new gasket fits easily in the track and seals the door properly.
5. Install the new gasket.
6. Starting at the top of the door, work the new door gasket into the track. Work your way down both sides of the door and across the bottom.
7. Check for loose spots and adjust the gasket as needed for a proper fit.
8. Spread a thin coat of petroleum jelly along the sealing surface of the door gasket to help the new gasket seal properly.
9. Close the door and check the fit. The door gasket should fit tightly against the cabinet and door with no gaps showing. Smooth out any creases that cause gaps. Push the door gasket further into the track to eliminate gaps.
10. Turn the refrigerator back on or restore power to the refrigerator.
11. Use the same procedure to replace the freezer door gasket.
We hope this video helped you out today. Please subscribe to our channel to see more repair tips and tricks.
For more DIY help, visit
searspartsdirect.com/diy/repair-help?sid=soc:youtube:DIY
Find parts for your refrigerator at
searspartsdirect.com/category/1234589/refrigerator-parts?sid=soc:youtube:refrigerator-parts










