Uploaded October 2026 | Updated November 2026, 3 hours ago
This is a practical DIY/handyman tutorial video showing a real-world method for extracting a sheared-off, heavily rusted screw that is stuck inside a wall plug (also called a wall anchor or Rawlplug). The screw had previously held a shower board/riser in place and had rusted through completely, leaving a broken stub in the plug. The video demonstrates both failed initial attempts and a successful technique using a diamond-coated hole saw, followed by reinstallation with a new plug and screw.
The presenter shows a rusty screw that has sheared off inside a wall plug. A small portion of the broken screw is still protruding. He notes that stainless steel or rust-resistant screws should ideally be used in damp environments like bathrooms to prevent this issue.
First attempt – gripping tools
He tries to grip the protruding stub with mole grips (locking pliers). This fails because the grips are not effective enough. He switches to water pump pliers (groove-joint pliers), manages to get a better grip, and starts turning the screw. However, the remaining metal shears off even further, leaving a broken piece stuck in the pliers and an even shorter stub in the wall plug.
Successful extraction method
He switches to a diamond-coated hole saw fitted in a small cordless drill.
Technique shown: Spin the hole saw up to speed.
Lightly touch it on the end of the broken screw/plug.
Lift slightly so the spinning saw centers itself on the screw and begins cutting into the plastic wall plug around it.
This progressively removes the wall plug material until the entire plug (with the remaining screw fragment inside) comes free.
Reinstallation The old hole is cleaned.
A new wall plug is inserted and tapped into place.
The shower riser/board is refixed using a manual screwdriver (he specifically advises against using a power drill/driver to avoid overtightening or breaking anything).
Both the top and bottom screws are installed and gently nipped up.
The decorative cover is clipped back on.
Closing
The presenter confirms the riser is now firmly fixed. He mentions he has other videos on removing broken screws and bolts and invites viewers to watch those. He thanks the audience for watching.
This video is useful for anyone dealing with seized or broken screws in wall plugs, especially in bathrooms or other damp locations where corrosion is common. The diamond hole-saw technique is presented as an effective last-resort method when conventional gripping tools fail.
This is a practical DIY/handyman tutorial video showing a real-world method for extracting a sheared-off, heavily rusted screw that is stuck inside a wall plug (also called a wall anchor or Rawlplug). The screw had previously held a shower board/riser in place and had rusted through completely, leaving a broken stub in the plug. The video demonstrates both failed initial attempts and a successful technique using a diamond-coated hole saw, followed by reinstallation with a new plug and screw.
The presenter shows a rusty screw that has sheared off inside a wall plug. A small portion of the broken screw is still protruding. He notes that stainless steel or rust-resistant screws should ideally be used in damp environments like bathrooms to prevent this issue.
First attempt – gripping tools
He tries to grip the protruding stub with mole grips (locking pliers). This fails because the grips are not effective enough. He switches to water pump pliers (groove-joint pliers), manages to get a better grip, and starts turning the screw. However, the remaining metal shears off even further, leaving a broken piece stuck in the pliers and an even shorter stub in the wall plug.
Successful extraction method
He switches to a diamond-coated hole saw fitted in a small cordless drill.
Technique shown: Spin the hole saw up to speed.
Lightly touch it on the end of the broken screw/plug.
Lift slightly so the spinning saw centers itself on the screw and begins cutting into the plastic wall plug around it.
This progressively removes the wall plug material until the entire plug (with the remaining screw fragment inside) comes free.
Reinstallation The old hole is cleaned.
A new wall plug is inserted and tapped into place.
The shower riser/board is refixed using a manual screwdriver (he specifically advises against using a power drill/driver to avoid overtightening or breaking anything).
Both the top and bottom screws are installed and gently nipped up.
The decorative cover is clipped back on.
Closing
The presenter confirms the riser is now firmly fixed. He mentions he has other videos on removing broken screws and bolts and invites viewers to watch those. He thanks the audience for watching.
This video is useful for anyone dealing with seized or broken screws in wall plugs, especially in bathrooms or other damp locations where corrosion is common. The diamond hole-saw technique is presented as an effective last-resort method when conventional gripping tools fail.










