Uploaded September 2020 | Updated November 2026, 2 days ago
H Bridge DC Motor Driver Circuit/Control [40A PWM, Power Mosfets] using IR2104 Mosfet Driver and IRF3205
========================================
Altium Designer + License (Free): altium.com/yt/myvanitar
========================================
Article: pcbway.com/blog/technology/Powerful_H_Bridge_DC_Motor_Driver.html
========================================
Check other videos: bit.ly/2N9OlPa
========================================
An H-Bridge (Full-Bridge) driver is quite popular in driving loads such as brushed DC motors and it is widely used in robotics and industry. The main advantages of using an H-Bridge driver are high efficiency, rotation direction change, and breaking the motor. In this article/video, I have introduced a complete H-Bridge DC motor driver using four IR3205 power MOSFETs and two IR2104 MOSFET drivers. Theoretically, the above-mentioned MOSFET can handle currents up to 80A, however, in practice we can expect to get currents up to 40A if the MOSFET temperature is kept as low as possible, using a big heatsink or even a fan.
Inspired by: DroneBot Workshop, Controlling DC Motors with the L298N H Bridge and Arduino, URL: youtu.be/dyjo_ggEtVU
Inspired by: ElectroBOOM, Brushed DC Motors and How to Drive Them, URL: youtu.be/yO9xIVv8ryc
Inspired by: Circuit Magic, How to control DC motor with L298N driver and Arduino, URL: youtu.be/dyZolgNOomk
H Bridge DC Motor Driver Circuit/Control [40A PWM, Power Mosfets] using IR2104 Mosfet Driver and IRF3205
========================================
Altium Designer + License (Free): altium.com/yt/myvanitar
========================================
Article: pcbway.com/blog/technology/Powerful_H_Bridge_DC_Motor_Driver.html
========================================
Check other videos: bit.ly/2N9OlPa
========================================
An H-Bridge (Full-Bridge) driver is quite popular in driving loads such as brushed DC motors and it is widely used in robotics and industry. The main advantages of using an H-Bridge driver are high efficiency, rotation direction change, and breaking the motor. In this article/video, I have introduced a complete H-Bridge DC motor driver using four IR3205 power MOSFETs and two IR2104 MOSFET drivers. Theoretically, the above-mentioned MOSFET can handle currents up to 80A, however, in practice we can expect to get currents up to 40A if the MOSFET temperature is kept as low as possible, using a big heatsink or even a fan.
Inspired by: DroneBot Workshop, Controlling DC Motors with the L298N H Bridge and Arduino, URL: youtu.be/dyjo_ggEtVU
Inspired by: ElectroBOOM, Brushed DC Motors and How to Drive Them, URL: youtu.be/yO9xIVv8ryc
Inspired by: Circuit Magic, How to control DC motor with L298N driver and Arduino, URL: youtu.be/dyZolgNOomk







![DC Motor Driver Circuit Using Power MOSFETs [PWM Controlled, 30A Half Bridge]
DC Motor Driver Circuit using Power Mosfets [PWM Controlled, 30A Half Bridge]
Altium Designer: https://www.altium.com/yt/myvanitar
Article: http://bit.ly/2LRBYXH
Check other videos: http://bit.ly/2N9OlPa
DC motors are everywhere, from hobby applications to robotics and industrial areas. Therefore there is wide usage and request for suitable and powerful DC motor drivers. In this article, we will learn to build one. You can control it using a Microcontroller, an Arduino, a Raspberry Pi, or even a standalone PWM generator chip. By using proper heatsink and cooling methods, this circuit can handle currents up to 30A.
Welcome!
I’m sure you are curious to know about this circuit and you want to build it. So let me start to explain it first by schematic analysis.
As you can see the heart of this circuit is this MOSFET driver chip. I’ve selected a popular chip which is IR2104. It can drive almost any MOSFET, especially power MOSFETs which are known to have big input capacitance.
That’s actually the main reason why we have to use a MOSFET driver.
The IR2104 is a Half-Bridge driver. The Half-Bridge configuration can deliver more current to the load, besides the load is ground referenced. This is important for some applications.
The capacitors C1 and C2 are used to reduce the noise. I’ve selected minimum 100V rated capacitors because I assumed the worst conditions. 100V is equal with the maximum MOSFET Vds tolerable voltage.
If you are sure that your load voltage is low (For example a 12V DC motor), then you can increase the capacitance and reduce the rated voltages to for example 25V (for instance 1000uf-25V).
There is enough space on the PCB which allows you to use a variety of capacitors. What I used here are 100nF-250V and 220uF-100V.
The last remaining point from this schematic is the input pins of the MOSFET driver. I have pulled down the SD Pin with a 4.7K resistor. Therefore if you apply a steady-state Logic level voltage to the SD pin, you can enable the chip. Otherwise, the chip is disabled and it will not transfer the PWM signal to the MOSFETs. We can say the SD pin acts as a switch.
You will inject your PWM pulse to the IN pin. You can use a Microcontroller, Arduino, Raspberry Pi or another chip such as TL494 to build and control the PWM duty cycle.
I used SamacSys schematic symbols and PCB footprints for the IR2104 driver and IRFP150 MOSFETs. Because at least I will not waste my time to design them from scratch which sometimes accompanies mistakes. All SamacSys services are free of charge.
Don’t forget to follow the description to get more information and see the reference links.
If we briefly look at the IR2104 datasheet, we can see it introduces a few nice features such as input logic compatibility and separate chip and load supply injection capability. It means the power supply for the MOSFET driver and the load’s supply do not need to be identical, but both supplies are certainly ground referenced.
As it is stated, the load supply voltage can reach up to 600V, if the MOSFETs are rated similarly.
The above picture shows the designed PCB layout. The bottom pictures show the assembled circuit board and it is ready for a test. This is just a fast semi-homemade PCB board to test the circuit and to make sure about its true operation.
But you should choose a professional PCB fabrication company because now you are sure the circuit works flawlessly. I suggest you PCBWay.
As it is clear, I have excluded some tracks to not to be covered by the solder mask. The reason is that these tracks might carry a high amount of current, but the PCB track itself cannot tolerate high current flows and will burn out. Therefore you must solder a bare solid copper wire on these uncovered areas to enhance the track’s current transmission capability. For my initial tests, it wasn’t necessary because my selected load consumes less than 3A.
If you want to use the circuit for high current loads, never forget to mount the MOSFETs on a proper heatsink and please make the isolation between each MOSFET and the heatsink using a silicone insulation pad. These pads block the electricity but transfer the heat to the heatsink flawlessly.
#dc_motor_driver
#brushed_motor_driver
#mosfet_driver
#pwm_driver
#motor_driver DC Motor Driver Circuit Using Power MOSFETs [PWM Controlled, 30A Half Bridge]](https://i.ytimg.com/vi/9UVxvpHyqMI/mqdefault.jpg)

![Battery Capacity Tester, Identify a Fake Lithium ion Battery, Using Arduino [Lithium-NiMH-NiCd]
Battery Capacity Tester, Identify a Fake Lithium ion Battery, Using Arduino [Lithium-NiMH-NiCd]
By Arduino-Nano and constant current load circuit
Altium Designer: https://www.altium.com/yt/myvanitar
Full Article: https://www.pcbway.com/blog/technology/Battery_capacity_measurement_using_Arduino.html
Variable Switching Power Supply: https://youtu.be/ywFpNdvSC7A
Check other videos: http://bit.ly/2N9OlPa
Features:
Identify a fake Lithium-Ion/Lithium-Polymer/NiCd/NiMH battery
Adjustable constant current load (can also be modified by the user)
Capable of measuring the capacity of almost any kind of battery (below 5V)
Easy to solder, build, and use, even for beginners (all components are Dip)
An LCD user interface
Specifications:
Board Supply: 7V to 9V(Max)
Battery Input: 0-5V(max) – no reverse polarity
Constant Current Load: 37mA to 540mA(max) – 16 Steps – can be modified by the user
The true measurement of a battery’s capacity is essential for many scenarios. A capacity measurement device can solve the problem of spotting fake batteries as well. Nowadays fake Lithium and NiMH batteries are everywhere which don’t handle their advertised capacities. Sometimes it is difficult to distinguish between a real and a fake battery. This problem exists in the spare batteries market, such as cell phone batteries. Furthermore, in many scenarios, it is essential to determine the capacity of a second-hand battery (for instance a laptop battery). In this article, we will learn to build a battery capacity measurement circuit using the famous Arduino-Nano board. I’ve designed the PCB board for dip components. So even beginners can solder and use the device.
#arduino_battery_capacity_tester
#identify_fake_lithium_battery
#battery_capacity_meter Battery Capacity Tester, Identify a Fake Lithium ion Battery, Using Arduino [Lithium-NiMH-NiCd]](https://i.ytimg.com/vi/AJvhhS8I3Ps/mqdefault.jpg)
![[Updated Schematic] AC-DC Switching Power Supply
[Updated Schematic] AC-DC Switching Power Supply
Altium Develop (Legal License): https://www.altium.com/yt/MyVanitar
Schematic & PCB: https://365.altium.com/files/5E02104B-7D68-4C35-836F-AC9FC0618A65
Other Videos: http://bit.ly/2N9OlPa
@AtiumOfficial
#altiumstories
In this video, I’ll show you my 85V–240VAC to 5VDC 2A Flyback Switching Power Supply, designed and built around the Viper22A controller IC.
The circuit provides a stable 5V / 2A DC output from a wide AC input range (85V to 240VAC), making it suitable for universal power applications. [Updated Schematic] AC-DC Switching Power Supply](https://i.ytimg.com/vi/AThzvB-4130/mqdefault.jpg)