DC to DC Boost Converter Circuit Using XL6019 @MyVanitar
DC to DC Boost Converter Circuit Using XL6019  @MyVanitar
Uploaded June 2024 | Updated November 2026, 2 days ago
DC to DC Boost Converter (step-up) Circuit Using XL6019
======================================
Article: powerelectronicsnews.com/a-dc-to-dc-boost-converter-using-xl6019
======================================
Vevor Europe: https://s.vevor.com/bfQ48e
Discount code: VVGDS5
======================================
Altium Designer + Legal License (Free): altium.com/yt/myvanitar
======================================
Altium 365: altium.com/altium-365
======================================
OctoPart: octopart.com
======================================
Schematic/PCB: 365.altium.com/files/D19174CC-20DB-48D1-89ED-615C737BE5EF
======================================
Other Videos: bit.ly/2N9OlPa
======================================
The output voltage of USB Type-C mobile chargers and power banks is fixed at 5V. A small efficient boost converter circuit can convert them to a 12V power source. 12V is one of the most commonly used voltage levels to supply electronic devices.

This article introduces a circuit to cover such a requirement using the XLSEMI automotive/industrial graded boost/buck-boost/inverting XL6019 chip. The chip input voltage range is 5V to 40V and the switching frequency is fixed at 180KHz, so the input voltage can be higher (for example, 9V). The maximum switching current of the chip is 5A, at 25 degrees C. A multiturn potentiometer allows the user to set the output voltage precisely to 12.0V. The internal NMOS of the chip reduces the PCB board size, complexity, and EMI (RdsON:110mR, 25 degrees C). The chip offers excellent line/load regulation figures and an internal soft starter circuit.

The XL6019 regulator is a wide input range, current mode, DC/DC converter which is capable of generating either positive or negative output voltages. It can be configured as either a boost, flyback, SEPIC, or inverting converter. The XL6019 built-in N-channel power MOSFET and fixed frequency
oscillator, current-mode architecture results in stable operation over a wide range of supply and output voltages. The XL6019 regulator is a special design for portable electronic equipment applications.

Schematic and PCB have been designed using Altium Designer 24. The PCB board has been tested against output voltage stability, temperature stress, and output noise using Siglent SDL1020X-E DC load, VEVOR SC240M thermal imaging camera, and Siglent SDS1104X-E oscilloscope. The PCB layout of the converter was designed with several precautions such as implementing power planes, low EMI, VIAs, and low ground path impedance. The input connector is a 5A USB Type-C, which makes it suitable for nowadays portable applications.
DC to DC Boost Converter Circuit Using XL6019AI Generated Radar PCB, Right or Fake? 😧 😶LM317 AC to 0-12VDC-1A Adjustable Power SupplyLow-Pass LC-CLC (Pi) Filter Simulation and Damping using Altium Develop Mixed Simulation (Mixed Sim)12V-5A to 24V-2.5A Conversion – AC to DC SMPS Modification Step-by-StepDC Motor Driver Circuit Using Power MOSFETs [PWM Controlled, 30A Half Bridge]Load Step Response Test Using Siglent SDL1000X-E DC Load and SDS2000X Plus OscilloscopeBattery Capacity Tester, Identify a Fake Lithium ion Battery, Using Arduino [Lithium-NiMH-NiCd][Updated Schematic] AC-DC Switching Power SupplySoft Starter Circuits (Inrush Current Limiter) for AC and DC Loads0-30V, 0-7A Adjustable Switching Power Supply [CC-CV, Buck Converter]Transformerless 85-260V-AC to 12V-DC Power Supply
MyVanitar |

DC to DC Boost Converter Circuit Using XL6019

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER