DIY Laptop Sleeve-cum-Stand from old Jeans @StitchSWearShantiSingh
DIY Laptop Sleeve-cum-Stand from old Jeans  @StitchSWearShantiSingh
Uploaded December 2020 | Updated November 2026, 17 hours ago
#LaptopSleeve #LaptopStand #Sleevecumstand

DIY Laptop Sleeve cum Stand from old jeans

Supplies Needed:
About 1/2 yard of piece from your old jeans (this could vary slightly depending on the size of your laptop. Get more if you want to be safe.)
Small pieces of Velcro


Machine Maintenance: bit.ly/3dNazkm

Sewing Machine Maintenance - How Motor Work's (Part 3)

Playlist:
1. Presser Foot: bit.ly/2AJp769
2. Machine Maintenance: bit.ly/3dNazkm
3. Art Work Deepika Padukone Portrait: bit.ly/300x5Tf

Must Have Products:
32 Presser Foot Pack: amzn.to/3eIKDHp
Flower Presser Foot: amzn.to/386wrWl
Tailoring Kit Scale 1: amzn.to/3g3491A
Tailoring Kit scale 2: amzn.to/3eGq26E
TAiloring kit Scale 3: amzn.to/2BQneVN
VArdhman Thread: amzn.to/3i751Ed
Double Needle Set: amzn.to/3g7374M

Sewing Instructions:

Start out by laying your laptop on your felt. You will want to cut a piece of felt that is about an inch and a half wider than your computer, or in other words, has a 3/4 inch excess on each side of your computer.

So my computer is 12 1/2 inches by about 9 inches, so I want my sleeve to be about 14 inches by 10 1/2 inches.

How to make laptop case
I doubled up the felt to make the sleeve more cushiony. If you prefer a slimmer sleeve, just do one layer. I will continue this tutorial assuming that the double layer.


Cut 2 pieces according to the measurements above that will work for your computer.

Then cut 2 more pieces that are the same width but are about 6-7 inches longer. This will create your flap.

Pin all 4 pieces together with the two smaller ones in front and the two bigger in back. (Note-I rounded out the corners on mine because I like the look of round corners better. You can do this if you would like or leave them square.)

Sew all the way around the outside of the case. Part of this will have you sewing through 4 layers and part through just 2. Use as small of a seam allowance as you can.

How to sew a laptop sleeve

Then you will need to sew across just the two layers that go across the middle, being careful that you ONLY sew through those two and not the rest of the sleeve. Sorry, forgot to take a picture of how to do this, but here is one from another tutorial that is the same idea:

Sew across that center section.

Then, trim the excess all the way around the sleeve to give it a nice, straight, clean finish.

Grab your Velcro pieces and figure out where you want them. Two will go on the underside of the flap near the top and then fold the flap down and mark where they meet up with the sleeve and sew your other pieces there:

And that’s it! You are already done! Hopefully that was quick and easy for you and hopefully, you can really enjoy this sleeve! Grab some hot chocolate while you work on your laptop. It makes life happy!
DIY Laptop Sleeve-cum-Stand from old Jeans76th Independence Day Embroidery: Celebrating with the Tricolor Flag  || Stitch & SwearHow to Use Flower Presser Foot - Complete Tutorial HindiSurbala Laishram for winning gold medal at the Global Association of Mixed Martial Arts 2021DIY Home Made Mask - Recommended by CDCSLEEVE DESIGN LATEST 2019नवरात्रि का दूसरा दिन - ब्रह्मचारिणी देवी || Triangle Cut Kurti || Kite Cut Kurti - CuttingDIY Designer Top Drafting And Cutting- With Full Body MeasurementLatest Collar Design 2022|| Cutting & Stitching || नवरात्रि का पांचवा दिन - स्कंदमाताDESIGNER TOP DRAFTING AND CUTTING 2019How to Use Double Welting / Piping Foot - Installation & TutorialDIY Envelope Sleeve Drafting And Cutting ll 1st time in INDIA
Stitch And SWear |

DIY Laptop Sleeve-cum-Stand from old Jeans

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER