Uploaded September 2026 | Updated November 2026, 9 hours ago
Learn how to retopologize a face in Blender using the PolyQuilt add-on. In this step-by-step Blender retopology tutorial, I demonstrate how to quickly build a clean, low-poly quad mesh over a 3D scan or high-poly model while establishing the important edge loops needed for later modeling and subdivision.
Rather than trying to add every detail immediately, this workflow focuses on creating the major topology structure first. You’ll build loops around the eyes, nose, nostrils, mouth, and entire face, then fill the remaining areas with quads. Once the base topology is complete, Blender’s standard modeling tools and Subdivision Surface modifier can be used to increase resolution and refine the model.
This PolyQuilt workflow is especially useful for retopologizing 3D scans, creating facial masks, designing body extensions, preparing models for 3D printing, or building clean geometry that can be further sculpted and modeled.
Topics covered:
- Setting up an empty mesh for retopology
- Enabling Blender retopology display
- Using PolyQuilt over a high-poly model or 3D scan
- Using face snapping and mirror mode
- Building clean quad topology
- Creating edge loops around the eyes
- Creating an eye-mask topology loop
- Building nose and nostril loops
- Creating mouth and facial edge loops
- Connecting and filling topology with quads
- Adding additional edge loops
- Using the Subdivision Surface modifier
- Moving from low-poly to higher-detail geometry
- Preparing facial topology for masks and 3D printing
Timestamps:
00:00 Blender face retopology with PolyQuilt
00:26 Create an empty mesh for retopology
00:39 Enable retopology display and face snapping
00:52 Select the PolyQuilt tool
01:05 Start building topology around the eye
01:18 Create the first eye quads
01:30 Establish the eye edge loop
01:43 Snap and reposition vertices
01:56 Focus on major topology structure
02:10 Check the eye loop
02:21 Begin the nose and mouth topology
02:34 Create the eye-mask loop
02:47 Complete the eye-mask structure
03:00 Add geometry around the nose and mouth
03:17 Turn the topology down the face
03:29 Build broad facial topology
03:41 Complete the nose and mouth loop
03:52 Create the nose loop
04:15 Add divisions for additional topology
04:28 Begin the nostril loops
04:41 Build topology around the nostril
04:55 Close the nostril quads
05:09 Extend the nose topology
05:25 Connect the remaining nose geometry
05:40 Review the facial edge loops
05:52 Begin the mouth loop
06:05 Build topology around the mouth
06:21 Adjust the PolyQuilt geometry
06:33 Connect the mouth topology
06:45 Join the lower face geometry
07:00 Build the outer face loop
07:19 Continue around the top of the face
07:34 Manage edge-loop counts
07:46 Review all major face loops
07:59 Fill the remaining topology
08:21 Complete the quad mesh
08:38 Add additional Blender edge loops
08:48 Add a Subdivision Surface modifier
09:01 Refine the higher-resolution mesh
09:13 Continue modeling and adding detail
09:24 Facial masks and 3D-printing applications
PolyQuilt makes Blender retopology much more direct by letting you concentrate on the important edge flow first and refine the surface later. Keeping the initial mesh simple also makes it much easier to modify proportions and add supporting loops where they are actually needed.
#Blender #Retopology #PolyQuilt #BlenderTutorial #3DModeling #FaceTopology #QuadTopology #3DScanning #3DPrinting #BlenderAddons
youtube.com/channel/UCmGXH-jy0o2CuhqtpxbaQgA/join
Learn how to retopologize a face in Blender using the PolyQuilt add-on. In this step-by-step Blender retopology tutorial, I demonstrate how to quickly build a clean, low-poly quad mesh over a 3D scan or high-poly model while establishing the important edge loops needed for later modeling and subdivision.
Rather than trying to add every detail immediately, this workflow focuses on creating the major topology structure first. You’ll build loops around the eyes, nose, nostrils, mouth, and entire face, then fill the remaining areas with quads. Once the base topology is complete, Blender’s standard modeling tools and Subdivision Surface modifier can be used to increase resolution and refine the model.
This PolyQuilt workflow is especially useful for retopologizing 3D scans, creating facial masks, designing body extensions, preparing models for 3D printing, or building clean geometry that can be further sculpted and modeled.
Topics covered:
- Setting up an empty mesh for retopology
- Enabling Blender retopology display
- Using PolyQuilt over a high-poly model or 3D scan
- Using face snapping and mirror mode
- Building clean quad topology
- Creating edge loops around the eyes
- Creating an eye-mask topology loop
- Building nose and nostril loops
- Creating mouth and facial edge loops
- Connecting and filling topology with quads
- Adding additional edge loops
- Using the Subdivision Surface modifier
- Moving from low-poly to higher-detail geometry
- Preparing facial topology for masks and 3D printing
Timestamps:
00:00 Blender face retopology with PolyQuilt
00:26 Create an empty mesh for retopology
00:39 Enable retopology display and face snapping
00:52 Select the PolyQuilt tool
01:05 Start building topology around the eye
01:18 Create the first eye quads
01:30 Establish the eye edge loop
01:43 Snap and reposition vertices
01:56 Focus on major topology structure
02:10 Check the eye loop
02:21 Begin the nose and mouth topology
02:34 Create the eye-mask loop
02:47 Complete the eye-mask structure
03:00 Add geometry around the nose and mouth
03:17 Turn the topology down the face
03:29 Build broad facial topology
03:41 Complete the nose and mouth loop
03:52 Create the nose loop
04:15 Add divisions for additional topology
04:28 Begin the nostril loops
04:41 Build topology around the nostril
04:55 Close the nostril quads
05:09 Extend the nose topology
05:25 Connect the remaining nose geometry
05:40 Review the facial edge loops
05:52 Begin the mouth loop
06:05 Build topology around the mouth
06:21 Adjust the PolyQuilt geometry
06:33 Connect the mouth topology
06:45 Join the lower face geometry
07:00 Build the outer face loop
07:19 Continue around the top of the face
07:34 Manage edge-loop counts
07:46 Review all major face loops
07:59 Fill the remaining topology
08:21 Complete the quad mesh
08:38 Add additional Blender edge loops
08:48 Add a Subdivision Surface modifier
09:01 Refine the higher-resolution mesh
09:13 Continue modeling and adding detail
09:24 Facial masks and 3D-printing applications
PolyQuilt makes Blender retopology much more direct by letting you concentrate on the important edge flow first and refine the surface later. Keeping the initial mesh simple also makes it much easier to modify proportions and add supporting loops where they are actually needed.
#Blender #Retopology #PolyQuilt #BlenderTutorial #3DModeling #FaceTopology #QuadTopology #3DScanning #3DPrinting #BlenderAddons
youtube.com/channel/UCmGXH-jy0o2CuhqtpxbaQgA/join










