Uploaded February 2018 | Updated November 2026, 12 hours ago
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we review how to create an outdoor top-rope anchor using a cordelette. To create this type of top rope anchor you’ll need:
1 - Cordelette, 6 to 8 millimeters in length
2 - Non-locking carabiners
AND
1 - Locking carabiner -and- 1 non-locking carabiner
OR
2 - non locking carabiners
OR
2 - locking carabiners for the Master Point
Step 1 - Clip a non-locking carabiner into each bolt (one carabiner for each bolt).
Step 2 - Clip cordelette into each non-locking carabiner.
Step 3 - Pull the strands down to isolate the two legs of the anchor (if you see a triangle of cordelette, you are not properly equalized). If the cordelette is too long, you can double it up to keep the Master Point higher. If you decide to double it up, make sure all strands get tied off in your Master Point, and that your system is both equalized and redundant when you tie the knot.
Step 4 - Pull the cordelette in the direction of the climber until it is equalized (See video Top Rope Anchor Safety Considerations - SRENE for more on anchors). Pinch the two sides of the rope together and tie a figure-eight-on-a-bight to create the Master Point.
Step 5 - Clip a locking and non-locking carabiner, opposite and opposed, into the Master Point. You can also use two non-locking or two locking carabiners.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we review how to create an outdoor top-rope anchor using a cordelette. To create this type of top rope anchor you’ll need:
1 - Cordelette, 6 to 8 millimeters in length
2 - Non-locking carabiners
AND
1 - Locking carabiner -and- 1 non-locking carabiner
OR
2 - non locking carabiners
OR
2 - locking carabiners for the Master Point
Step 1 - Clip a non-locking carabiner into each bolt (one carabiner for each bolt).
Step 2 - Clip cordelette into each non-locking carabiner.
Step 3 - Pull the strands down to isolate the two legs of the anchor (if you see a triangle of cordelette, you are not properly equalized). If the cordelette is too long, you can double it up to keep the Master Point higher. If you decide to double it up, make sure all strands get tied off in your Master Point, and that your system is both equalized and redundant when you tie the knot.
Step 4 - Pull the cordelette in the direction of the climber until it is equalized (See video Top Rope Anchor Safety Considerations - SRENE for more on anchors). Pinch the two sides of the rope together and tie a figure-eight-on-a-bight to create the Master Point.
Step 5 - Clip a locking and non-locking carabiner, opposite and opposed, into the Master Point. You can also use two non-locking or two locking carabiners.
We hope you found this video helpful.
Please remember, climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!

![Alpine & Mountaineering: 8. Changing Directions in Snow | Climbing Tech Tips
Subscribe to our channel for the latest training videos, climbing tutorials and more! Let’s look at how to change directions when climbing steep snow slopes. When switchbacking up a steep snow slope, you will obviously have to change directions—multiple times!
Here are the steps for changing direction, while maintaining a self belay with the ice axe for security:
Step 1: Take an “out of balance” cross over step (legs crossed).
Step 2: Move your other foot up and into the same plane, so you’re standing in the “duck walk” position with both hands on your ice axe in a “self belay.” See the video for demonstrations, and for more on walking techniques, see our video on “Snow Travel - Duck Foot”[hyperlink to video].
Step 3: Change hands on your ice axe so that when you change directions your axe is still in the uphill hand. Spin the head of the ice axe so you have the same grip as before the turn (this will likely be the “self arrest” grip with pick backwards, but some may prefer a pick-forward grip).
Step 4: Move your foot into an “in balance” foot position (legs uncrossed, uphill foot forward), and continue to walk or climb in the new direction of travel.
We hope you found this video helpful.
Please remember, climbing and mountaineering are inherently dangerous. Climb at your own risk. Visit https://ClimbingTechTips.com for related comments, additional videos, and community feedback! Alpine & Mountaineering: 8. Changing Directions in Snow | Climbing Tech Tips](https://i.ytimg.com/vi/X_FgwLin678/mqdefault.jpg)








