Uploaded October 2026 | Updated November 2026, 3 hours ago
The bench welcomed a dead Astron RS-20A power supply, its telltale smell revealing that it had already released the dreaded "magic smoke." We set out to trace the failure, which quickly pointed to two primary culprits: a destroyed bridge rectifier and a blown regulator/crowbar protection circuit.
Our initial testing began with a Variac, slowly bringing up the mains voltage. While the main reservoir capacitor showed zero DC voltage, the ancillary rail powering the regulator IC and TIP29 driver remained active. We confirmed AC was arriving at the bridge rectifier, but no DC was leaving. After verifying there were no dead shorts across the DC rails, we pulled the rectifier; testing confirmed it was completely defective—diodes shorted, & the other half fully open-circuit, and feeding raw AC toward the main capacitor, a dangerous condition that risked exploding the capacitor.
Replacing the bridge rectifier successfully brought back main DC, but the output spiked far above the expected 13.8 V DC. The moment we touched the voltage adjustment potentiometer, the crowbar protection circuit aggressively tripped, shorting the output and blowing the main fuse.
Tracing the DC path revealed the chain reaction:
The potentiometer’s dirty wiper had lost contact on its internal carbon track, sending a false reading that forced the regulated voltage past the SCR crowbar threshold.
When the SCR fired to protect the load, the sudden high-current draw destroyed the TIP29 NPN driver transistor along with a 1N4004 diode in the drive line to the 2N3771 power transistors.
Without clean drive signals fed to the bases of those rear series pass elements, no voltage could safely reach the output terminals.
We replaced the blown fuse, TIP29, and 1N4004 diode, then flushed the potentiometer with switch lubricant cleaner, working the wiper back and forth to clear away track contaminants. With the control circuit stabilized, we powered up via the Variac and dialed in a solid 13.8 V DC. A final load test proved the unit held rock-steady—another successful repair in the books!
Summary of Parts Replaced & Serviced
Bridge Rectifier: Replaced (blown SHORT CIRCUIT diodes / open circuit).
Driver Transistor (TIP29 NPN): Replaced (blown due to overcurrent).
Diode (1N4004): Replaced (smoked in the drive path to 2N3771 bases).
Potentiometer: Cleaned and lubricated (cured intermittent dirty wiper track).
AC Fuse: Replaced (blown by SCR crowbar activation).
The bench welcomed a dead Astron RS-20A power supply, its telltale smell revealing that it had already released the dreaded "magic smoke." We set out to trace the failure, which quickly pointed to two primary culprits: a destroyed bridge rectifier and a blown regulator/crowbar protection circuit.
Our initial testing began with a Variac, slowly bringing up the mains voltage. While the main reservoir capacitor showed zero DC voltage, the ancillary rail powering the regulator IC and TIP29 driver remained active. We confirmed AC was arriving at the bridge rectifier, but no DC was leaving. After verifying there were no dead shorts across the DC rails, we pulled the rectifier; testing confirmed it was completely defective—diodes shorted, & the other half fully open-circuit, and feeding raw AC toward the main capacitor, a dangerous condition that risked exploding the capacitor.
Replacing the bridge rectifier successfully brought back main DC, but the output spiked far above the expected 13.8 V DC. The moment we touched the voltage adjustment potentiometer, the crowbar protection circuit aggressively tripped, shorting the output and blowing the main fuse.
Tracing the DC path revealed the chain reaction:
The potentiometer’s dirty wiper had lost contact on its internal carbon track, sending a false reading that forced the regulated voltage past the SCR crowbar threshold.
When the SCR fired to protect the load, the sudden high-current draw destroyed the TIP29 NPN driver transistor along with a 1N4004 diode in the drive line to the 2N3771 power transistors.
Without clean drive signals fed to the bases of those rear series pass elements, no voltage could safely reach the output terminals.
We replaced the blown fuse, TIP29, and 1N4004 diode, then flushed the potentiometer with switch lubricant cleaner, working the wiper back and forth to clear away track contaminants. With the control circuit stabilized, we powered up via the Variac and dialed in a solid 13.8 V DC. A final load test proved the unit held rock-steady—another successful repair in the books!
Summary of Parts Replaced & Serviced
Bridge Rectifier: Replaced (blown SHORT CIRCUIT diodes / open circuit).
Driver Transistor (TIP29 NPN): Replaced (blown due to overcurrent).
Diode (1N4004): Replaced (smoked in the drive path to 2N3771 bases).
Potentiometer: Cleaned and lubricated (cured intermittent dirty wiper track).
AC Fuse: Replaced (blown by SCR crowbar activation).










