Aid Climbing & Big Walls: 15. How to Pendulum & Lower Out While Cleaning | Climbing Tech Tips @ClimbingTechTips
Aid Climbing & Big Walls: 15. How to Pendulum & Lower Out While Cleaning | Climbing Tech Tips  @ClimbingTechTips
Uploaded February 2018 | Updated November 2026, 3 days ago
Subscribe to our channel for the latest training videos, climbing tutorials and more! In this video we look at how to pendulum and lower out when cleaning a pitch of aid. When the follower encounters a pendulum, there are a few ways to accomplish this technical move. We will show you our most commonly used technique.

Be sure to practice this technique at your local crag—and not for the first time when you are thousands of feet off the deck!

Let’s outline this step-by-step:

Step 1: Approach the pendulum point, which is usually a fixed piece gear such as a piton (“pin”), and will contain either a carabiner or a piece of “tat” (left cord or webbing). If you don’t like what is there to lower from, now is the time to make it something you trust—back it up with your extra webbing, or a leave a carabiner.

Step 2: Pull a bight of rope up from your tie in point.

Step 3: Feed the bight through the tat or carabiner and clip this bight into a locking carabiner attached to your belay loop. Lock the carabiner.

Step 4: Ratchet yourself toward the fixed piece using the pulley system you just built on your harness. Your tie in point should be taught. Hold yourself in place once you are close to the pendulum point and you have slackened the lead line.

DO NOT LET GO of this ratcheting rope system running from your belay loop through the pendulum point—this is now essentially your belay.


Note at this point you can clip into the fixed piece

Step 5: The lead line should now have slack in it so you can pass the piece with the top jumar and remove the gear from the rock, leaving only the fixed piece and the item which you are lowering from.

Step 6: Cinch up the top jumar to get as tight as you can on the rope above you, then slowly, with a firm grip on the pendulum line, start to lower yourself out.

Step 7: Once you are hanging vertically again, your weight should be back on your jumars. Unclip the bight of rope from the locking biner on your belay loop, and pull that loop out of the pendulum by pulling from your tie in.

Advanced Trick:

Sometimes the pendulum is too far, or it is early on the pitch so the length of rope you have below your tie in is not enough to make it across. If that is the case, there is an advanced trick which involves untying from the rope—so be doubly sure you are adequately backed up.

Step 1: Approach the ‘pendi’ (pendulum) point.

Step 2: Tie a “figure-eight-on-a-bight” beneath your lowest jumar, and clip that to your belay loop with a locking carabiner. This is now your main connection point to the rope.

Step 3: Untie from the lead line.

Step 4: Take the tail of the rope and thread it through the pendulum point. Pull the rope through until it is tight on your figure-eight-on-a-bight, which is clipped to your harness.

Step 5: Put the rope behind the pendulum point (which you just threaded through) into a belay device, and then cinch yourself closer to the pendulum point.

Step 6: The rope above you should now be slack, so you can pass the piece, retrieve any of your gear, and cinch the top jumar as high as possible above you.

Step 6: Keep a firm grip on the brake strand and lower yourself, as if you were lowering someone on top-rope from that pendulum point — but that someone getting lowered is also you!

With this method, you have more rope available (up to the end of the rope) to lower yourself out.

Step 7: Once your weight is on your jumars again, you can unclip the rope from your belay device and pull the end through the pendulum point.

Step 8: Once you have retrieved the end of the rope, tie back into the end of the rope and then unclip and untie the figure-eight-on-a-bight. Remember to keep tying backup knots when you have 10-20 feet of slack in the rope below you.

Now you can continue cleaning the pitch.

These are essential techniques to any Big Wall or Aid Climbing adventure. Be sure to practice and have a working knowledge of these systems before venturing onward.


We hope you found this video helpful.

Please remember, climbing is inherently dangerous. Climb at your own risk. Visit ClimbingTechTips.com for related comments, additional videos, and community feedback!
Aid Climbing & Big Walls: 15. How to Pendulum & Lower Out While Cleaning | Climbing Tech TipsGym Top Rope Climbing: 1. Gear Considerations | Climbing Tech TipsTraditional Climbing: 14. Alternative Trad Anchor - Consideration #1 | Climbing Tech TipsBasic & Intermediate Outdoor Climbing: 7. Top Rope Anchor - Using a Cordelette | Climbing Tech TipsAlpine & Mountaineering: 17. Selecting Alpine Boots | Climbing Tech TipsAlpine & Mountaineering: 8. Changing Directions in Snow | Climbing Tech TipsAid Climbing & Big Walls: 2. Additional Aid Gear | Climbing Tech TipsMulti-Pitch Trad: 9. Racking Part 2 of 2 | Climbing Tech TipsMulti-Pitch Trad: 14. Finding the Route and Descent | Climbing Tech TipsIce Climbing: 11. Falling Considerations | Climbing Tech TipsAlpine & Mountaineering: 15. Snow Anchors - Using your Ice Axe | Climbing Tech TipsClimbing Movement: 2. Direction of Pull | Climbing Tech Tips
Climbing Tech Tips |

Aid Climbing & Big Walls: 15. How to Pendulum & Lower Out While Cleaning | Climbing Tech Tips

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER