Uploaded December 2021 | Updated November 2026, 2 days ago
AC RMS Current Measurement [220V Mains Line] Using the Siglent SDS2000X Plus Oscilloscope (SDS2102X Plus) and Siglent SDM3045X Multimeter, Using a Current Transformer and the formula editor feature
=========================================
Check other videos: bit.ly/2N9OlPa
=========================================
Measuring the AC current (220V mains RMS current) is not as simple as measuring the DC current. In the DC current measurement, you can simply hook the oscilloscope probe to the shunt resistor and calculate the voltage difference and the current, however, that is not the case with the mains line, otherwise, you will blow up your device.
There are some tools to overcome this problem such as the differential probe or the current probe, however, you can do this using a cheap current transformer (provides galvanic isolation) and the formula editor feature of the SDS2000X Plus series oscilloscope (Waveform).
I used a Siglent SDM3045X multimeter as a reference where it can measure both the AC RMS Voltage and the AC RMS Current.
Related Videos:
What is RMS value | Easiest Explanation | TheElectricalGuy:youtube.com/watch?v=Ynv_C3N0fPk
Alternating Current vs Direct Current - Rms Voltage, Peak Current & Average Power of AC Circuits:youtube.com/watch?v=ERIToctYUcQ
Difference between AC and DC Current Explained | AddOhms #5: youtube.com/watch?v=vN9aR2wKv0U
AC RMS Current Measurement [220V Mains Line] Using the Siglent SDS2000X Plus Oscilloscope (SDS2102X Plus) and Siglent SDM3045X Multimeter, Using a Current Transformer and the formula editor feature
=========================================
Check other videos: bit.ly/2N9OlPa
=========================================
Measuring the AC current (220V mains RMS current) is not as simple as measuring the DC current. In the DC current measurement, you can simply hook the oscilloscope probe to the shunt resistor and calculate the voltage difference and the current, however, that is not the case with the mains line, otherwise, you will blow up your device.
There are some tools to overcome this problem such as the differential probe or the current probe, however, you can do this using a cheap current transformer (provides galvanic isolation) and the formula editor feature of the SDS2000X Plus series oscilloscope (Waveform).
I used a Siglent SDM3045X multimeter as a reference where it can measure both the AC RMS Voltage and the AC RMS Current.
Related Videos:
What is RMS value | Easiest Explanation | TheElectricalGuy:youtube.com/watch?v=Ynv_C3N0fPk
Alternating Current vs Direct Current - Rms Voltage, Peak Current & Average Power of AC Circuits:youtube.com/watch?v=ERIToctYUcQ
Difference between AC and DC Current Explained | AddOhms #5: youtube.com/watch?v=vN9aR2wKv0U
![Hand Sanitizer/Alcohol Dispenser Circuit/DIY, Without an Arduino/MCU [Fight with COVID-19]
DIY Automatic Hand Sanitizer/Alcohol Dispenser [Non-Contact], without an Arduino/MCU [Fight with COVID-19]
In this article/video, you will learn how to build a hand sanitizer/alcohol dispenser device, without any MCU, programming, or Arduino. lets fight with COVID-19 and COVID-20 with technology.
Article: https://www.pcbway.com/blog/technology/DIY_Automatic_Hand_Sanitizer_Dispenser without_Arduino_or_MCU.html
Check other videos: http://bit.ly/2N9OlPa
#COVID_19
#hand_sanitizer
#hand_sanitizer_dispenser
#DIY_Hand_sanitizer_dispenser
Inspired by:
TechBuilder
DIY Automatic Alcohol Dispenser ($3 No Arduino Needed)
URL: https://www.youtube.com/watch?v=5yojb3vL-go
Inspired by:
NONC
Automatic touchless Hand Sanitizer Dispenser V2.0
URL: https://www.youtube.com/watch?v=e5OIw1jsRJs
Inspired by:
Global Fun
How to make Automatic hand sanitizer Stand Using PVC pipes
URL: https://www.youtube.com/watch?v=Qywa4dUVtLY Hand Sanitizer/Alcohol Dispenser Circuit/DIY, Without an Arduino/MCU [Fight with COVID-19]](https://i.ytimg.com/vi/uPCaQr7uWlQ/mqdefault.jpg)
![Police LED Flasher Circuit [72 LEDs, STM8S001]
Police LED Flasher Circuit using an STM8S001 [72 LEDs]
Police LED Flasher circuit can be used for cars, motorcycles, bicycles .. etc. Such an LED Flasher circuit is easy to build. Just follow the design.
Article Source: https://www.pcbway.com/blog/technology/Programmable_Police_LED_Flasher_Using_an_STM8.html
Support me on Patreon: https://www.patreon.com/myvanitar
Check other videos: http://bit.ly/2N9OlPa
C2 and C3 are used to reduce the input voltage noise. Then the voltage is applied to the 78M09 [1] (REG1) regulator. It is used to stabilize the voltage at 9V. C4 and C6 are used to reduce the regulator’s output noise.
The output of the REG1 is handled to a first-order RC filter (R28 and C5). It helps to reduce the noise even further because this device might be used continuously in a noisy environment, such as a vehicle. The best way to examine the behavior of this filter (or other filter types) is to perform a practical measurement. The SDS1104X-E oscilloscope introduced a nice Bode plot feature that can perform this useful calculation.
REG2 [2] is used to convert 9V to 5V to supply the STM8s001 MCU [3] (IC1). C7 is a supplementary filtering capacitor for the IC1.
IC1 MCU is programmed using a single SWIM wire. It stands for the Single-Wire Interface Module. It is a high-speed link between the MCU and the programmer/debugger. This pin must be connected to the SWIM pin of the programmer/debugger. The ground pin must also be connected. This completes the connection (P2).
IC2 and IC3 are logic N-Channel SMD Mosfets [4] that are used to turn on/off the LEDs. The gate pins of both MOSFETs have been pulled down using 4.7K resistors to avoid unwanted triggering (R13, R14). SW1 is a tactile push button that is used to switch between flasher programs. R27 is a pull-up resistor and C8 reduces the possible push-button debouncing noises.
R1 to R26 resistors are used to limit the LEDs current. In each part, I have put 3 LEDs in series that are connected to the +9V rail (Figure 2). The characteristics of LEDs vary from manufacturer to manufacturer. Therefore we can not assign a fixed limiting series resistor for all circumstances. The maximum tolerable current of a 5mm LED is around 25mA. Therefore the resistor value that could limit the current to somewhere around 15mA (a bit higher than a half) looks sufficient and does not affect the LEDs’ lifetime and does not significantly decrease the LED brightness.
You can start from a 100-Ohm resistor and increase it and simultaneously monitor the current. In my case, I read 15mA by using a 180-ohm resistor.
#Police_LED_Flasher_Circuit
#police
#flasher
#stm8s Police LED Flasher Circuit [72 LEDs, STM8S001]](https://i.ytimg.com/vi/v0_3puzW-wk/mqdefault.jpg)

![220Vac to 5Vdc Transformerless Power Supply Circuit Using LNK304 [read the disclaimer below]
Disclaimer: This circuit is an industrial upgrade for the capacitor-based supply solution, it is connected to the 220V-AC Mains, non-galvanically isolated. if you are not familiar with the electrical safety rules, please avoid this content or ask some professionals to guide you. The author (or anybody else or any company) is NOT responsible for any harm or damage. Do it at your own risk. This is not for beginners!
Altium Designer + License (Free): https://www.altium.com/yt/myvanitar
Article: https://www.pcbway.com/blog/technology/220Vac_to_5Vdc_Transformerless_Power_Supply_Using_LNK304_5b2e2d7d.html
https://www.pcbway.com/project/shareproject/220Vac_to_5Vdc_Transformerless_Power_Supply_Using_LNK304_46d16791.html
220Vac to 5Vdc Transformerless Power Supply Circuit Using LNK304 (without transformer)
Whenever you hear the transformerless supply term, you initially imagine the capacitor-based solution, which means a high voltage capacitor in series with the mains line, then a bridge rectifier, a Zener diode, a filtering capacitor, and so on. Such a circuit is not just unable to deliver sufficient current for many applications, also, it is not a reliable solution for the industry, although you might see such circuits in some cheap products that are designed to have a low cost.
A month ago, I was repairing a washing machine mainboard. In the examination process, I realized that it is equipped with an LNK304 chip that is used in transformerless supplies. So I decided to design a circuit based on this chip to be used in your applications. The circuit contains 220VAC mains input protection, output filtering, and a regulator.
To design the schematic and PCB, I used Altium Designer 22 and the SamacSys component libraries (Altium plugin). To get high-quality fabricated PCB boards, I sent the Gerbers to PCBWay and purchased original components using the componentsearchengine.com. To test the current handling and stability of the output voltage, I used the Siglent SDL1020X-E DC Load and examined the power supply output noise using the Siglent SDS2102X Plus oscilloscope.
Music by Atch
SoundCloud: https://bit.ly/AtchSoundCloud
Spotify: https://bit.ly/AtchSpotify
Instagram: https://instagram.com/atchmusic 220Vac to 5Vdc Transformerless Power Supply Circuit Using LNK304 [read the disclaimer below]](https://i.ytimg.com/vi/xDg_F0XNcvU/mqdefault.jpg)
![🔶 Wireless Home Automation (Control and Monitoring) Using a Nextion HMI Display
Wireless Home Automation [Control and Monitoring] Using a Nextion HMI Display
Altium Designer + License (Free): https://www.altium.com/yt/myvanitar
OctoPart: https://octopart.com
Article: https://www.pcbway.com/blog/technology/Wireless_Home_Automation_Control_and_Monitoring_Using_a_Nextion_HMI_Display_24d9be1d.html
Gerber/PCB (PanelBoard): https://www.pcbway.com/project/shareproject/Wireless_Home_Automation_Control_and_Monitoring_Using_a_Nextion_HMI_Display_Pa_5356e3bd.html
Gerber/PCB (MainBoard): https://www.pcbway.com/project/shareproject/Wireless_Home_Automation_Control_and_Monitoring_Using_a_Nextion_HMI_Display_Ma_e22f20e6.html
Nextion HMI: https://bit.ly/3dY30gw
Other Videos: http://bit.ly/2N9OlPa
Nowadays home automation is a trending topic among electronic enthusiasts and even the mass population. People are busy with their life challenges, so an electronic device should take care of the home instead! The majority of such devices need internet or Wi-Fi for connectivity or they don’t offer a user-friendly GUI, but I decided to design a standalone wireless monitoring/controlling unit that can be adjusted using a graphical and touch-controlled LCD display.
The device consists of a panelboard and a mainboard that communicate using 315MHz (or 433MHz) ASK transceivers. The panel side is equipped with a high-quality 4.3” capacitive-touch Nextion Display. The user can monitor the live temperature values and define the action threshold (to activate/deactivate the heater or cooler), humidity (to activate/deactivate the humidifier or dehumidifier), and ambient light (to turn ON/OFF the lights). The mainboard is equipped with 4 Relays to activate/deactivate the aforementioned loads.
To design the schematic and PCB, I used Altium Designer 23. The fast component search engine (octopart) allowed me to quickly consider components’ information and also generate the BOM. To get high-quality fabricated boards, I sent the Gerber files to PCBWay. I used the Arduino IDE to write the MCU code, so it is pretty easy to follow and understand. Designing a GUI using the Nextion tools was a pleasant experience that I will certainly follow for similar projects in the future. So let’s get started :-) 🔶 Wireless Home Automation (Control and Monitoring) Using a Nextion HMI Display](https://i.ytimg.com/vi/xSR63yVP-EI/mqdefault.jpg)

![Switching Power Supply Circuit Using LM2576/LM2596 [Adjustable, Buck Converter, CC-CV]
Switching Power Supply Circuit Using LM2576/LM2596 [Adjustable, Buck Converter, CC-CV]
Switching power supplies are known for high efficiency. An adjustable voltage/current supply is an interesting tool, which can be used in many applications such as a Lithium-ion/Lead-acid/NiCD-NiMH battery charger or a standalone power supply. In this article, we will learn to build a variable step-down buck converter using the popular LM2576-Adj chip.
Source Article: http://bit.ly/2YshM5t
Support me on Patreon: https://www.patreon.com/myvanitar
Check other videos: http://bit.ly/2N9OlPa
Features
Cheap and easy to build and use
Constant current and constant voltage adjustment [CC, CV] capability
1.2V to 25V and 25mA to 3A controlling range
Easy to adjust the parameters (optimum use of variable resistors to control the voltage and current)
The design follows the EMC rules
It is easy to mount a heat-sink on the LM2576
It uses a real shunt resistor (not a PCB track) to sense the current
The heart of the circuit is the LM2576-Adj chip. It is a popular, cheap, and handy buck converter IC. According to the LM2576 datasheet: “TS2576 Series are step-down switching regulators with all required active functions. It is capable of driving 3A load with excellent line and load regulations. These devices are available in fixed output voltages of 3.3V, 5V and adjustable output version. TS2576 series operates at a switching frequency of 52kHz thus allowing smaller sized filter components than what would be needed with lower frequency switching regulators. It substantially not only reduces the area of board size but also the size of a heat sink, and in some cases, no heat sink is required. The ±4% tolerance on output voltage within specified input voltages and output load conditions is guaranteed. Also, the oscillator frequency accuracy is within ±10%. External shutdown is included. Featuring 70μA (typical) standby current. The output switch includes cycle-by-cycle current limiting, as well as thermal shutdown for full protection under fault conditions” [1].
Capacitors C1 and C2 are used to reduce input noise. D1, L1, C3, C4, and PS1 are the typical buck converter circuit ingredients. C3 and C4 are used parallelly instead of a single capacitor because using parallel capacitors reduces the final capacitor’s ESR value. Simply it means using two 470uF capacitors in parallel is better than using a big 1000uF capacitor.
R1 to R4 construct a shunt resistor. I have used four 0.5R-1%-1W resistors that make an accurate 0.125R-4W resistor. The current flow over this resistor generates a voltage drop, which we used it to sense the current.
REG1 makes a fixed 9V supply for the IC1 [2]. IC1 is used to amplify the voltage drop on the shunt resistor because small current flows do not make a big voltage drop over a 0.125R resistor. So we have to use an amplifier here. IC1 is configured as a non-inverting amplifier that can deliver 820x gain maximum. Potentiometer R7 defines the gain, so the minimum gain is around 4x. Therefore this potentiometer defines the maximum output current.
The potentiometer R6 adjusts the output voltage. The diode D2 blocks the feedback voltage path to IC1. otherwise, we are not able to adjust the voltage and current simultaneously. I have included the D2’s voltage drop into consideration and have compensated it using the IC1 gain.
C5, C6, and C7 are used to reduce the noise. C6 defines the cut-off frequency of the amplifier that will not amplify high-frequency noises. R6 and R7 values are selected wisely. So by turning the potentiometers, you will experience smooth voltage/current changes.
According to the EMC guidelines, I/O lines that transmit/receive signals through cables/wires (especially high frequency), should be placed near each other (for example on one edge of the board). Otherwise, the potential difference between the ground return paths will cause noise or interference. More importantly, where the main circuit itself runs at high frequencies. Although our circuit does not deal with high frequencies, it is always a good practice to follow the guideline.
#LM2576
#LM2596
#Adjustbale_switching_power_supply
#variable_switching_power_supply
#variable_DC_to_DC_buck_converter Switching Power Supply Circuit Using LM2576/LM2596 [Adjustable, Buck Converter, CC-CV]](https://i.ytimg.com/vi/ywFpNdvSC7A/mqdefault.jpg)

