Uploaded September 2022 | Updated November 2026, 2 days ago
40V 30A Adjustable Switching Power Supply (DC to DC Buck Converter, DC to DC Step Down Converter)
======================================
Altium Designer + License (Free): altium.com/yt/myvanitar
OctoPart: octopart.com
======================================
Article: pcbway.com/blog/technology/40V_30A_Adjustable_Switching_Power_Supply_6ff75733.html
======================================
Other Videos: bit.ly/2N9OlPa
======================================
A DC-to-DC converter is one of the most commonly used circuit topologies in electronics, especially in power supply applications. There are three main types of DC-to-DC converters (non-isolated): Buck, Boost, and Buck-Boost. Sometimes a buck converter is also called a step-down converter and a boost converter is also called a step-up converter. A buck converter reduces/steps down the input voltage while increasing the output current.
In this article/video, I introduced an adjustable buck converter circuit that can deliver up to 30A and handle up to 40V at the input. The output voltage is adjustable from 3V to 37.5V. Several PCB design rules were followed to enhance output stabilization and current handling, also to reduce the radiated emission, and noise figure.
To design the schematic and PCB, I used Altium Designer 22 and the electronic search engine (octopart) to easily and quickly collect information about the necessary components. To get high-quality fabricated boards, I sent the Gerber files to PCBWay and finally tested the current handling, output stability, and noise figure using the Siglent SDL1020X-E DC load, Siglent SDM3045X multimeter, and Siglent SDS2102X Plus oscilloscope. Just build one and have fun!
Specifications
Input Voltage: 6-40VDC
Output Current: 30A (max continuous, See text)
Output Voltage: 3-37.5VDC Adjustable
Output Noise: 50mVpp, 4mVrms (18A load)
40V 30A Adjustable Switching Power Supply (DC to DC Buck Converter, DC to DC Step Down Converter)
======================================
Altium Designer + License (Free): altium.com/yt/myvanitar
OctoPart: octopart.com
======================================
Article: pcbway.com/blog/technology/40V_30A_Adjustable_Switching_Power_Supply_6ff75733.html
======================================
Other Videos: bit.ly/2N9OlPa
======================================
A DC-to-DC converter is one of the most commonly used circuit topologies in electronics, especially in power supply applications. There are three main types of DC-to-DC converters (non-isolated): Buck, Boost, and Buck-Boost. Sometimes a buck converter is also called a step-down converter and a boost converter is also called a step-up converter. A buck converter reduces/steps down the input voltage while increasing the output current.
In this article/video, I introduced an adjustable buck converter circuit that can deliver up to 30A and handle up to 40V at the input. The output voltage is adjustable from 3V to 37.5V. Several PCB design rules were followed to enhance output stabilization and current handling, also to reduce the radiated emission, and noise figure.
To design the schematic and PCB, I used Altium Designer 22 and the electronic search engine (octopart) to easily and quickly collect information about the necessary components. To get high-quality fabricated boards, I sent the Gerber files to PCBWay and finally tested the current handling, output stability, and noise figure using the Siglent SDL1020X-E DC load, Siglent SDM3045X multimeter, and Siglent SDS2102X Plus oscilloscope. Just build one and have fun!
Specifications
Input Voltage: 6-40VDC
Output Current: 30A (max continuous, See text)
Output Voltage: 3-37.5VDC Adjustable
Output Noise: 50mVpp, 4mVrms (18A load)
![Switching Power Supply Circuit Using LM2576/LM2596 [Adjustable, Buck Converter, CC-CV]
Switching Power Supply Circuit Using LM2576/LM2596 [Adjustable, Buck Converter, CC-CV]
Switching power supplies are known for high efficiency. An adjustable voltage/current supply is an interesting tool, which can be used in many applications such as a Lithium-ion/Lead-acid/NiCD-NiMH battery charger or a standalone power supply. In this article, we will learn to build a variable step-down buck converter using the popular LM2576-Adj chip.
Source Article: http://bit.ly/2YshM5t
Support me on Patreon: https://www.patreon.com/myvanitar
Check other videos: http://bit.ly/2N9OlPa
Features
Cheap and easy to build and use
Constant current and constant voltage adjustment [CC, CV] capability
1.2V to 25V and 25mA to 3A controlling range
Easy to adjust the parameters (optimum use of variable resistors to control the voltage and current)
The design follows the EMC rules
It is easy to mount a heat-sink on the LM2576
It uses a real shunt resistor (not a PCB track) to sense the current
The heart of the circuit is the LM2576-Adj chip. It is a popular, cheap, and handy buck converter IC. According to the LM2576 datasheet: “TS2576 Series are step-down switching regulators with all required active functions. It is capable of driving 3A load with excellent line and load regulations. These devices are available in fixed output voltages of 3.3V, 5V and adjustable output version. TS2576 series operates at a switching frequency of 52kHz thus allowing smaller sized filter components than what would be needed with lower frequency switching regulators. It substantially not only reduces the area of board size but also the size of a heat sink, and in some cases, no heat sink is required. The ±4% tolerance on output voltage within specified input voltages and output load conditions is guaranteed. Also, the oscillator frequency accuracy is within ±10%. External shutdown is included. Featuring 70μA (typical) standby current. The output switch includes cycle-by-cycle current limiting, as well as thermal shutdown for full protection under fault conditions” [1].
Capacitors C1 and C2 are used to reduce input noise. D1, L1, C3, C4, and PS1 are the typical buck converter circuit ingredients. C3 and C4 are used parallelly instead of a single capacitor because using parallel capacitors reduces the final capacitor’s ESR value. Simply it means using two 470uF capacitors in parallel is better than using a big 1000uF capacitor.
R1 to R4 construct a shunt resistor. I have used four 0.5R-1%-1W resistors that make an accurate 0.125R-4W resistor. The current flow over this resistor generates a voltage drop, which we used it to sense the current.
REG1 makes a fixed 9V supply for the IC1 [2]. IC1 is used to amplify the voltage drop on the shunt resistor because small current flows do not make a big voltage drop over a 0.125R resistor. So we have to use an amplifier here. IC1 is configured as a non-inverting amplifier that can deliver 820x gain maximum. Potentiometer R7 defines the gain, so the minimum gain is around 4x. Therefore this potentiometer defines the maximum output current.
The potentiometer R6 adjusts the output voltage. The diode D2 blocks the feedback voltage path to IC1. otherwise, we are not able to adjust the voltage and current simultaneously. I have included the D2’s voltage drop into consideration and have compensated it using the IC1 gain.
C5, C6, and C7 are used to reduce the noise. C6 defines the cut-off frequency of the amplifier that will not amplify high-frequency noises. R6 and R7 values are selected wisely. So by turning the potentiometers, you will experience smooth voltage/current changes.
According to the EMC guidelines, I/O lines that transmit/receive signals through cables/wires (especially high frequency), should be placed near each other (for example on one edge of the board). Otherwise, the potential difference between the ground return paths will cause noise or interference. More importantly, where the main circuit itself runs at high frequencies. Although our circuit does not deal with high frequencies, it is always a good practice to follow the guideline.
#LM2576
#LM2596
#Adjustbale_switching_power_supply
#variable_switching_power_supply
#variable_DC_to_DC_buck_converter Switching Power Supply Circuit Using LM2576/LM2596 [Adjustable, Buck Converter, CC-CV]](https://i.ytimg.com/vi/ywFpNdvSC7A/mqdefault.jpg)

