Police LED Flasher Circuit [72 LEDs, STM8S001] @MyVanitar
Police LED Flasher Circuit [72 LEDs, STM8S001]  @MyVanitar
Uploaded December 2019 | Updated November 2026, 2 days ago
Police LED Flasher Circuit using an STM8S001 [72 LEDs]

Police LED Flasher circuit can be used for cars, motorcycles, bicycles .. etc. Such an LED Flasher circuit is easy to build. Just follow the design.
=============================================
Article Source: pcbway.com/blog/technology/Programmable_Police_LED_Flasher_Using_an_STM8.html
=============================================
Support me on Patreon: patreon.com/myvanitar
=============================================
Check other videos: bit.ly/2N9OlPa
=============================================
C2 and C3 are used to reduce the input voltage noise. Then the voltage is applied to the 78M09 [1] (REG1) regulator. It is used to stabilize the voltage at 9V. C4 and C6 are used to reduce the regulator’s output noise.
The output of the REG1 is handled to a first-order RC filter (R28 and C5). It helps to reduce the noise even further because this device might be used continuously in a noisy environment, such as a vehicle. The best way to examine the behavior of this filter (or other filter types) is to perform a practical measurement. The SDS1104X-E oscilloscope introduced a nice Bode plot feature that can perform this useful calculation.
REG2 [2] is used to convert 9V to 5V to supply the STM8s001 MCU [3] (IC1). C7 is a supplementary filtering capacitor for the IC1.
IC1 MCU is programmed using a single SWIM wire. It stands for the Single-Wire Interface Module. It is a high-speed link between the MCU and the programmer/debugger. This pin must be connected to the SWIM pin of the programmer/debugger. The ground pin must also be connected. This completes the connection (P2).
IC2 and IC3 are logic N-Channel SMD Mosfets [4] that are used to turn on/off the LEDs. The gate pins of both MOSFETs have been pulled down using 4.7K resistors to avoid unwanted triggering (R13, R14). SW1 is a tactile push button that is used to switch between flasher programs. R27 is a pull-up resistor and C8 reduces the possible push-button debouncing noises.
R1 to R26 resistors are used to limit the LEDs current. In each part, I have put 3 LEDs in series that are connected to the +9V rail (Figure 2). The characteristics of LEDs vary from manufacturer to manufacturer. Therefore we can not assign a fixed limiting series resistor for all circumstances. The maximum tolerable current of a 5mm LED is around 25mA. Therefore the resistor value that could limit the current to somewhere around 15mA (a bit higher than a half) looks sufficient and does not affect the LEDs’ lifetime and does not significantly decrease the LED brightness.
You can start from a 100-Ohm resistor and increase it and simultaneously monitor the current. In my case, I read 15mA by using a 180-ohm resistor.




#Police_LED_Flasher_Circuit
#police
#flasher
#stm8s
Police LED Flasher Circuit [72 LEDs, STM8S001]2GHz, 5th-order Chebyshev Microstrip Bandpass Filter (FR-4)220Vac to 5Vdc Transformerless Power Supply Circuit Using LNK304 [read the disclaimer below]🔶 Wireless Home Automation (Control and Monitoring) Using a Nextion HMI Display40V-30A Adjustable Switching Power SupplySwitching Power Supply Circuit Using LM2576/LM2596 [Adjustable, Buck Converter, CC-CV]I2C Signal Decoding/Debugging using Siglent SDS2102X Plus and SDS1104X-E Oscilloscopes3V-15V to 5V-1A Buck Boost Converter using TPS63070
MyVanitar |

Police LED Flasher Circuit [72 LEDs, STM8S001]

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER