2003-08 CTS Brake Caliper Rebuild Part 4 Install Keith Noneya 2020-02-22 | DDescription: WARNING!!!! Working on brake systems is CRITICAL to vehicle safety. If improperly done it can lead to serious injury or death to you or others. KNOW what you are doing before working on any part of your braking system. If you don't, consult a professional or someone who is familiar with the proper maintenance and repair of the Braking systems. Your life and others with depend on that! This video series is intended to assist professionals or people familiar with the systems. If you are not, DO NOT attempt this procedure, then this video is for entertainment purposes only.Centric Caliper Repair Kit - Front P/N: 2768-05106972 $8.18 Part 1 is here: youtube.com/watch?v=MoiZX6qYXGQ&t=2sPart 2 is here: youtube.com/watch?v=bkJ7fyYSGoIPart 3 is here: youtube.com/watch?v=0FUhgSl035QPart 5 is here: youtube.com/watch?v=EORM8bSkm8kIf you learned something or found the video useful, please give the video a thumbs up for all the hours I put into it. If you want to help my channel more, please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya
Why Trump went Silent Pen Ha Ha Keith Noneya 2024-03-21 | Fun with Politics at Trumps Expense, or at least a pen. LOLThe 1st Amendment isn’t just for people we like or don't like, it’s essentially for those who we don’t like as well.When they speak it allows opposing views and exposes who they or who we really are. Let’s keep Free Speech Free!Thanks for Watching.Best Wishes & Blessings. Keith Noneya
How to replace a 4WD Switch & Test It on a 99-03 F250 F350 PN F75Z-7Z155-BA Keith Noneya 2024-02-10 | F250 F350 4WD Switch PN: F75Z-7Z155-BA Just a quick video on how to get this out and test it. I've never heard of one going bad but if one does you can test it before you go buy one. If you find and error in the video, by all means drop a comment. If you know of other videos on the subject "PLEASE" drop a link to them in a comment to help others. My channel is about the 99-03 F350 7.3L, Electronic Test Equipment and a few other misc items. If you like the video or leaned something please give the video a like. If you want to help my channel please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya
How to Clean Metal Electronic Equipment Cases & Covers Keith Noneya 2024-02-07 | Description: This video is how I clean the exterior of electronic equipment, what I use & why.When I make a new purchase I usually take the time to clean new item. This inspection is very important for four primary things for you. 1. It finds simple mechanical problems that could damage your equipment when it’s powered on.2. It helps you become familiar with the knobs and controls.3. It removes stickers or debris over the vents to help it breath better.4. It makes it look better.Here’s a list of items I use:1. General purpose cleaner like: Mr. Clean, 409, or dish soap and water about 1 part soap and 3 parts water. Do not spray your test equipment directly. It gets into the cracks and parts sensitive to water and soaps. Spray it on the rag or dip the rag or cloth into it.2. Isopropyl Alcohol: A little more aggressive and can help gently remove sticker residue, permanent Sharpe Ink & markers. If it’s been on there long enough, soak a paper towel and let it sit on the area. The Towel & Alcohol will pull it into the rag pores. The Con is if left it on to long the finish may start to dissolve finishes & paints. Test a area that won’t be seen.3. Brake Cleaner or Carburetor Cleaner: Works wonders, but VERY Aggressive on whatever it’s on. Like circuit boards, coatings, Rubber & Pot O-Rings. Use it stuff sparingly on the end of a tooth pick so it can be applied right to a needed area. 4. Paper towels. Cheap throw away’s, so you can use a fresh one every time. Cons: They can leave bits of paper towel in areas can get into switches and pots. Know where the bits are going.5. T-Shirt or Cotton Rags. They are capable of cleaning without larger bits that can get into things, can be washed & reused. They can leave micro fibers in your gear.6. Lint Free Rags: These have the best attributes of T-Shirts or Cotton Rags. The best option, but are more expensive.7. Acid brushes. Pros: One of my favorite tools. Can be made for soft scrubbers with long bristles or aggressive when cut short, or any manner of stiffness in between. So short bristles cut into heavy debris, and long they can sweep micro particles away. Resistant to most cleaners & chemicals. Cons: The metal sides can scratch components off a board or damage parts & surfaces. They fill up with contaminants and can be redeposited on areas you’re trying to clean.8. Canned Air: Canned air is great in that it can get places that brushes and items can’t get, that might even be damaged it a physical items was used. It’s also usually very dry air, unlike some shop air systems. It does have a few drawbacks: The propellant can get into things if the can is shaken or turned upside down or angled. As the can is used it creates moisture on the outside of the can that can drip into the equipment. It can also push items into cracks like Switches, Relay Contacts and Pot contact areas. Always cover areas that you don’t want debris in when using the air. 9. Red Erasers. They are great for cleaning the contacts on boards that have flat edge connectors. Just make sure you wipe from middle of the pad to the edge and ONLY in line with the trace. If you go from the edge inwards or from side to side they can rip up a trace or pad. Gentle action and some common sense will allow them to be a great cleaning too. Also be careful, like paper towels the eraser particles can get inside switches, contacts and pots.I hope that helped you learn some safe and known accepted ways to clean electronic equipment inside and out. If you learned something and found the video useful please give the video a thumbs up. I you would like to really help my channel and see more like this please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya.
Plastic Head Light Restore EASY Step by Step Keith Noneya 2023-12-27 | Just a quick video to show how easy it is to make your plastic headlights clear again to improve night time driving, especially in the rain. The vehicle is a 2014 Nissan Murano I've owned for years, and the most comfortable travel car I've ever owned, especially for cross country.Consumables Used:- 600 Grit Wet Dry Sand Paper. Most hardware stores will let you buy it by the sheet. .50.- 1200 Grit Wet Dry Sand Paper.- 2500 Grit Wet Dry Sand Paper.- Nu Finnish Car Polish. $11.49- Bucket of water.- Roll of Paper Towels.- Painters Tape to tape off the paint next to the light.Tools Used:- Mop Bucket or a large bowl to put the water in.- Cotton Rag or Clean T-Shirt.I hope you found the video helpful. If you learned something or found the video useful, please give it a like. If you'd like to help my channel please subscribe and ring the bell to let you know when I put a new video up. Best Wishes & Blessings. Keith Noneya
99-03 F Series Fuel Tank What They DONT Tell You Before You Drop it Keith Noneya 2023-08-16 | Just a quick video on some tubes to inspect and repair after you pull the Fuel Tank. I haven't seen one video mention these tubes. I used 5/8" Fuel Line to repair them over 9K miles ago. Included at the end of the video is a list of connections on the Fuel Tank and a look inside the tank for Harpooning the tank. For Harpooning the Tank I used a Kobalt 2" PVC Pipe Cutter Model # 58703 here if you need one: lowes.com/pd/Kobalt-2-In-in-PVC-cutter/1002633490 If you learned something or liked the video, please give it a thumbs up for the work I put into it. If you'd like to help my channel, please subscribe. Best Wishes & Blessings. Keith Noneya
1999 to 2007 F-Series AC Orifice Tube replacement Santech MT0093-1 Keith Noneya 2023-05-08 | Description: A quick video on how to replace the Orifice Tube on F-Series truck. The procedure is basically the same for most Fords however the location may be different between Trucks, Excursions, Mustangs etc. Caution! Make sure the system has been depressurized be for opening the Line to replace the Tube or any line or you may have AC Refrigerant and AC Oil sprayed on your face and clothing. If you don’t know what your doing get an experienced person to help you or a Professional to do the job. Stay Safe!Part Used: Santech PN: MT0093-1 RedTool Used: OEM PN: 25052 AC & Fuel Line Disconnect Tool Thanks for watching. If you found the video useful please give the video a thumbs up for my time. If you’d like to help my channel please subscribe. Best Wishes & Blessings. Keith Noneya
ACER 17 Inch Screen Replacement SUPER EASY ie N17C3 Keith Noneya 2023-05-07 | Description: How to replace a ACER Model N173C3 17 inch laptop screen Step by Step Super Easy!Part use: LP173FHM-N41 compatible with LP173WF4-SPF5Tools used:- Jewelers Phillips Screwdriver #1- Thick Guitar Pick or Phone Screen Tool KitThanks for watching. If you learned something give the video a Thumbs Up, Subscribe if you’d like to help. Best Wishes & Blessings. Keith Noneya00:00 Intro00:48 Bezel Removal01:26 Tool Kit02:43 LCD Separation03:35 Find the LCD Part Number04:05 Critical Screen Selection Notes06:17 Connector Separation07:34 New Screen Install08:01 Connecting the New Screen08:44 Checking the connection09:11 Mounting the New Screen10:11 Checking Screws10:30 Testing the Screen10:45 Remove Screen Protector & Install Bezel11:31 Summary and Closing
Snow Drive HWY-89 to Williams AZ 12 Dec 22 Keith Noneya 2022-12-23 | Just a quick video. It was the first big snow in Northern Arizona and my wife and I wanted to get out and see the snow on the trees, because we don't get that in Southern Louisiana. Sorry I haven't been posting regularly, I've been dealing with a death in the family and it's taken it's toll on the channel. I should start posting my regular content in Jan 23. Until then; Merry Christmas, Happy Hanukkah, Happy Holidays and a Happy New Year. Best Wishes & Blessings from my family to yours. Keith Noneya
99-03 F350 7.3L Cold Start 28 Deg Fahrenheit Keith Noneya 2022-12-13 | Video to show that if you maintain your truck; Glow Plug Relays, Glow Plugs (Original by the way), MAIH Relay MAIH (Manifold Air Inlet Heater) and have some winter oil in it, it should start right up. It was 28 Degrees outside when I checked but that was over two hours later after I had initially started it. So I'm sure the actual temperature was around 24 Degrees outside when I started it in the video for you guys. Thanks for watching guys. Best Wishes & Blessings. Keith Noenya
How to Remove Fix Stuck 7 3L HIPOP Lines Keith Noneya 2022-04-30 | Description: How to Remove Fix Stuck 7.3L Ford/International HIPOP Lines on 99-03 E & F-Series Trucks & Vans. This is just part of a Riff Raff HIPOP Aftermarket Line installation video that I may post. - If you’re reading this part in the Description I haven’t completed the RiffRaff video. Unfortunately I wasn't able to do the RiffRaff video do to my father passing away and I had to get my truck ready to go deal with my fathers estate, so I wasn't able to video the process due to time constraints. I so plan to start videos again in the next month or so, and some of them will be videos I had in work. Ie. What's in a GT38 Turbo etc.Tools I used:- 7.3L HIPOP Line Release tool. $8.00-35.00 eBay or Amazon. Search on eBay or Amazon.- 1/4” Flat head Screwdriver.- 9” Wobble Extension 3/8” Drive.- 19mm or 3/4” 3/8” Drive Crowfoot.- 3/8” Drive Ratchet.- 19mm or 3/4” Deep socket 3/8” Drive.- Shop Rag.- Step Stool.Parts you may need - New Stock & RiffRaff Line Part Numbers:- RiffRaff 99Late-03 Aftermarket Driver Screw on NO Quick Disconnect Line Coupler. PN: RDP-HPOP-DRVR $111.91- RiffRaff 99-03 Aftermarket Passenger Screw on NO Quick Disconnect Line Coupler. PN: RDP-HPOP-PASS $116.94- 99 Late-03 Stock Driver Quick Disconnect Line. PN: YC3Z9J323E $98.33- 99.5-03 Stock Quick Disconnect Line. PN: YC3Z9J323F $97.91- Early 99 Drivers Stock Quick Disconnect Line. PN: F81Z9J323E $98.33- Rear Stainless Steel Cross Over Line; PN: RDPHHPX $59.88- Stock HIPOP Fittings for Stock Lines PN: F81Z9C402AA $32.09 ea. Need one per hose on HIPOP- Fuel Bowl Outlet Line Top Drivers Side PN: Parker 60VLV-5 Viton Sleeve 5/16 inch RiffRaff PN: GZ-7-005 $2.54 - Fuel Bowl Inlet line Bottom Drivers Side PN: Parker 60VLV-6 Viton Sleeve 3/8 inch RiffRaff PN: GZ-7-006 $2.54 If you found the video helpful please give it a Thumbs Up. If you’d like to help my channel please subscribe. Thanks for watching and feel free to ask questions I read every comment and answer most of them personally. Best Wishes & Blessings. Keith Noneya
AUXITO 9007 HB5 12K Lummin Bulb Install & Review ie 99-04 F250 & F350 Keith Noneya 2022-03-18 | Description: AUXITO LED 9007/HB5-12K Headlamp bulbs Install & Review for your 99-04 F-250/350. I want to thank AUXITO for sponsoring todays video with a free set of LED Headlamps bulbs. I found them to be extremely helpful in improving visibility over stock head lamps. Other helpful video’s on the 99-04 F-250/350 lighting. * NO CUT 05-07 headlight Upgrade for 99-04 Ford F250 350 2LH-F250991PCG-RS* How to adjust 1 Piece Headlight Assemblies with no Adjusters PN-2LH F250991PCG-RSPart Used: - AUXITO 9007/HB5 Get them here: auxito.com/?ref=2nolcl9z0j** Click shop by application, Click Forward Lighting, Click Category, Click LED Bulbs, then complete the vehicle Information. The 1999 to 2003 is the 9007 HB5, but they have LED’s for other vehicles as well. When checking out type in discount code; keithnoneya for a 10-15% discount. Set by Auxito.- Dorman 42190 Headlamp Housing Retainer Clip.Light bulb Specs:-Material Cast 6063 Aluminum -Light source ZES chip with 12 LED’s 6 per side. Same height- Color Temp: 6500K XEON White.- Watts: Equivalent 30W/60Watt per set.- Brightness: 6000LM ea. 12,000LM per set. 200% Over Stock. - Dimensions: Same as 9007.Tools I used:- 9” Needle Nose Pliers with Teeth. Don’t use the smooth one they’ll just drop the clips. - No. 2 Phillips Screw Driver. Approx 9 inches long.- Paper Towels to block the clips from dropping behind the bumper. If you don’t use them, be prepared to pull the Passenger Battery, the Battery Tray and the Wash Bottle Assembly. Optional Tools:- Telescoping Magnet, so when the clips fall you can retrieve them easier. - 13mm Combination Wrench Set to remove the Battery Terminals.- 3/8” Drive Metric Ratchet & Socket Set. To remove, Battery Tray and Washer Bottle Assembly.- 9” Extension 3/8” Drive.I’m not an LED Headlight Bulb expert, I’m just like you but I’ve found these bulbs have significantly improved my lighting on the road. If you enjoyed the video and learned something please give the video a thumbs up. If you’d like to help my channel please subscribe or purchase a set of these bulbs using the link provided.My channel is about fixing vehicles, electronics and some misc. things on the side.Thanks for watching. Best Wishes & Blessings. Keith Noneya
How to remove a nail with no head or top Keith Noneya 2022-03-07 | How to remove a nail with no head doesn’t have to be a pain if done this way.Please give the video a thumbs up if you learned something and if you’d like to help my channel please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya
Ford 7 3L F250 F350 Passenger Battery Change Step by Step W Tips Keith Noneya 2022-01-26 | Description: How I changed my battery in my 2001 Ford F350 7.3L Lariat Crew Cab 4x4.Battery I used: Motorcraft BXT-65 850 amps.Tools I used & Recommended:- ½” or 13mm combination Wrench.- 12mm Combination Wrench if the others don’t fit.- Battery Terminal Cleaner.- 8mm 3/8” Drive Socket.- 9” 3/8” Drive Extension.- 3/8” Drive Stubby Ratchet.- Blade Screwdriver, large to help spread terminals if needed.- Multimeter, to measure voltages to ensure Alternator is working.- Battery Charger, if the batteries are low.Consumables Recommended: - Paper Towels.- Bottle of water or use a Garden hose to rinse off soda if used to clean corrosion off terminals.Chemical Recommended:- CRC Battery Terminal Protectant.- Permatex Anti-Seize Lubricant PN: 81343.- Soda Pop. For corrosion removal on battery terminals if needed.Thanks for watching. If you learned something or liked the video please give it a thumbs up.If you would like to help my channel please subscribe. Best Wishes & Blessings. Keith Noneya00:00 Introduction.00:22 Tools, Chemicals & Consumables needed.01:11 Cable Removal 13mm or ½” Combination Wrench.02:40 Battery Hold Down Clamp removal 8mm socket.03:24 Removing the Battery.03:50 Installing the NEW Battery.04:05 Battery Hold Down Clamp Installation 8mm socket Anti-Seize.05:02 Negative Terminal Cleaning.06:28 Connecting Negative Battery Terminal.06:51 Positive Terminal Cleaning.07:03 Connecting the Positive Battery Terminal.07:09 Tightening Cable Clamps.08:33 CRC Battery Terminal Treatment, Anti-Corrosion.09:28 Check Alternator Voltage & Conclusion.
99-03 7.3L F250 F350 Alternator Change Step by Step Keith Noneya 2022-01-15 | Description: How to change a 6G Series Alternator on a 99-03 F250-350 7.3L Step by Step with tips and explanations.Part I used: - Alternator 200 Amp Upgrade Kit PN 6G7796GYSMPLM $139.00. This kit comes with the Diode assembly already installed, a BIG HELP.- Link to it here: alternatorstarterrebuildkits.com/product/6g7796gysmpl- YouTube Link to video on how to do it: youtube.com/watch?v=hhpZ2Sc3j9s - I can’t strongly suggest enough, that if you rebuild your Alternator with this kit, to watch the video to ensure you don’t BLOW UP your new kit!- Link to WHY you need to charge your batteries FIRST BEFORE starting, alternatorstarterrebuildkits.com/alternator-installationAlternate Stock Part No's you can use: - 110 Amp P/N’s : 4U2Z10V346CKRM, F81U10300EB, F81Z10346EA, F81Z10346EARM & F81Z10V346EBRMTools Recommended:- ½” Drive Ratchet.- 3” Extension ½” Drive.- 13mm ½” Drive.- ½” Torque Wrench capable of 35 ft-lbs. (47Nm).- 10mm Combination Wrench.- 13mm Combination Wrench.- Battery Charger or Heavy Duty Jumper Cables & a vehicle to jump start the truck.- Step Stool or Chair.- Tire Step or chair. Powerbuilt 647596 Folding Heavy Duty Tire Steps for Truck SUV RV, $58.64 Plus Tax on Amazon or eBay.- Wire brush or piece of 100 grit sandpaper.- Small Multi-Meter to check Battery Voltages. Or check voltage on dash and that no Battery Symbol light is on the dash.Consumables Used:- Paper Towels.Optional Tools Recommended:- Wire Wheel on a bench grinder to clean the bolts. It just speeds cleaning them up.- Mechanics Gloves or plastic Gloves.- 12mm Combination Wrench.- 14mm Combination Wrench.Chemicals Uses:- Anti-Seize Lubricant Permatex 81343 or 133A.- Hand Cleaner.Thanks for watching folks. If you learned something or liked the video please give it a thumbs up. If you’d like to help my channel please subscribe. Best Wishes & Blessings. Keith Noneya
How to adjust 1 Piece Headlight Assemblies with no Adjusters PN-2LH F250991PCG-RS Keith Noneya 2021-12-21 | Description: How to adjust a 1 Piece Headlight Assembly that doesn’t have an adjustment screw. The basic measurement process is the same for all headlight assemblies on any vehicle, including this assembly. This video, including the basics, shows the specifics that apply to Part Numbers: 2LH-F250991PCG-RS, 2LH-F250991PCJM-RS & G7846816. Sold by Zoro, eBay and SPEC-D TUNING, Instyleparts and many others. The difference in this assembly and others is that most Headlight Assemblies have a screw to adjust the beam while these do not. So unless you know how to adjust them you’re stuck in whatever position you mounted them in. This video shows you where and how to adjust them to the proper height. Tools I used:- 9” Needle Nose Pliers with Teeth. Don’t use the smooth one they’ll just drop the clips. Optional Tools:- Paper Towels to block the clips from dropping behind the bumper. If you don’t use them, be prepared to pull the Passenger Battery, the Battery Tray and the Wash Bottle Assembly.- Telescoping Magnet, so when the clips fall you can retrieve them easier.- 3/8” Drive Metric Ratchet & Socket Set. To remove Batter, Battery Tray and Washer Bottle Assembly.- Metric Combination Wrench Set to remove the Battery Terminals.Thanks for watching. If you learned something or it helped you please give the video a thumbs up. If you'd like to help my channel please subscribe. Best Wishes & Blessings. Keith Noneya
Traxion Tailgate Ladder Install F250 F350 99 - 07 Keith Noneya 2021-12-12 | How to install a Traxion Tailgate Ladder on a F250 or F350 for 1999 to 2007.I show some options for the swing arms and the stow strap as well. They cost around $50.00 depending on where you buy it. You'll find them extremely helpful to easily get into your truck bed, especially if you have bad knees.Tools I used:- Center Punch.- Claw Hammer.- Black Marker Optional.- Electric Drill.- 9/64" Drill bit.- No. 2 Philips Tip.- 1/4 drive bit extender.- 3/16" Allen Wrench or a 5mm will do.- 10 mm Combination Wrench, Ratchet Type (Duwalt).- 4" Side Cutters, you can use a pocket knife or scissors.I hope you found the video useful. If you did please take the time to give it a thumbs up. If you'd like to help my channel please subscribe. I do truck, van, car, and electronic videos as well as a few misc things like lawn equipment.Best Wishes & Blessings. Keith Noneya
NO CUT 05-07 headlight Upgrade for 99-04 Ford F250 350 Spec-D Tuning Headlight 2LH-F250991PCG-RS Keith Noneya 2021-12-04 | Description: Complete Step by Step 1 Piece * NO CUT * 05-07 headlight upgrade for 99-04 Ford F250 F350 Spec-D Tuning Headlight PN 2LH-F250991PCG-RS. Want a direct Headlight Assembly plug and play upgrade with no cutting? Check these out on eBay or Zoro for under $160.00. Or on Amazon for $138.54 here; amazon.com/dp/B01H05QII0/?th=1I think you’ll really enjoy the look, these should get your attention! Some sellers assemblies don’t come with the 9007 bulbs so you may need to reuse the old ones, or install some AUXITIO LED bulbs here; youtube.com/watch?v=svE8Be-Su58&t=497sPros: - No CUTTING or Modifications needed to install them, A HUGE PLUS! It’s Plug & Play & If you want to revert back to your stock or similar style you can easily do it, It’s NOT permanent.- Price is very reasonable when compared to similar units.- Better Lighting than stock.- If you have to work on or replace an assembly with the same PN or another one you don’t have to remove the batteries after the initial installation, even if the style changes.Cons:- To change the Headlight Bulb you have to remove the top clips & loosen the bottom screws.- To change the Parking Bulb a complete removal is necessary, when stock is just two screws. So two clips and two screws isn’t that bad, besides other one pieces units are like this as well. - NO quick beam alignment screws, you have to pull the upper clips and adjust the mounting Screw Nuts. A bit of a hassle but once done you don’t have to do it again. Conclusion: If you’re on a budget and don’t mind playing with the weird alignment, or having to remove the whole assembly to replace the bulbs, then these are your best option.Part I used: 1 Piece Black Euro Headlights With LED- eBay search PN: 2LH-F250991PCG-RS ~ $158.99 - Alt Supplier ZORO PN: G7846816, 2LH-F250991PCJM-RS $143.55 (Plus Shipping) zoro.com Do a search for either Alt supplier Part Numbers. Or try Amazon here; amazon.com/dp/B01H05QII0/?th=1- Headlamp Housing Retainer 2 per Pack Dorman PN: 42190 ~ $4.99.Tools I used:- #2 Phillips Screw Driver.- 8” Needle Nose Pliers With Teeth (Don’t use smooth tips).- 6.5” Channel Lock Pliers No. 426. To remove Outer Lower Adjustment Screw. Amazon $17.45- 3/8” Drive Ratchet.- 3/8” Drive Stubby Ratchet.- 6” Wobble Extension 3/8” Drive.- 13mm 3/8” Drive Socket. To remove Airbox.- 8mm 3/8” Drive Socket. To remove Airbox.- 12-14mm Combination Wrenches to remove Battery Cables. I used 13mm but my clamp nut has been replaced, so one of those wrenches should fit yours.- Step Stool 12” High or a Heavy Duty Tire Step Powerbuilt PN: 647596 ~ $47.45.- Battery Post Cleaning Tool ~ $5.99.Optional Tools I used if: to help speed up the process or lower the bumper if needed.- Electric Screwdriver. - ¼” hex drive to 3/8” Drive Adapter Hercules Harbor Freight PN: 64604. ~ $6.49.- ½” Drive Ratchet.- 13mm ½” Drive Socket. To lower the bumper if needed.- 18mm ½” Drive Socket. To lower the bumper if needed. - Mechanics Roll Around Seat PITTSBURGH AUTOMOTIVE Harbor Freight PN 3338 ~ $32.00Chemicals I Used:- Silicon Grease for anti-water in the connectors, not shown in the video.- Anti-Seize Compound Permatex PN: 81343 or 133A.Consumables I used:- Paper Towels.I hope you enjoyed the video and found it useful. If you learned something please give the video a thumbs up. If you’d like to help my channel grow, please subscribe I’ll be uploading lots of future F350 repair videos. Thanks for watching. Best Wishes and Blessings. Keith Noneya
How to Access The Spare Tire On A F250 F350 99 - 007 Step by Step Keith Noneya 2021-11-24 | Hi folks just a quick video on where and how to lower and raise the spare tire on a Ford F250/F350 Truck. Hope you enjoy the video and find it useful. If you did please give it a thumbs up. If you'd like to help my channel please subscribe. Best Wishes & Blessings. Keith Noneya
Cataract Lake Area Williams Arizona Oct 2021 Keith Noneya 2021-10-27 | A view of the area around Cataract Lake just outside of Williams Arizona. It has some nice picnic tables, a boat ramp and some fishing to be done here. The view is spectacular and if you're ever in Williams you have to make an afternoon trip to the lake for a picnic. Thanks for watching folks. Best Wishes & Blessings. Keith Noneya
1999 to 2007 Ford F 250 350 450 Tire Hoist Change PN F81Z1A131AF Keith Noneya 2021-06-29 | Description: Hi folks here’s how to change your old Tire Hoist on your 1999-2007 Ford F-250 to F-450.Part I used: Gledewen Part Number: GW-QLTZJ02 I purchased it off Amazon here:amazon.com/gp/product/B07S35FFHZ/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1 for $55.99. Other Part Numbers that Apply:- 924-528- 924528- 6C3Z1A131AA- 2C3Z1A131AA- F81Z1A131AF- XC3Z1A131DA- YC3Z1A131AATools I used:- 1/2” 3/8” drive Socket.- 3/8” Drive Ratchet.- 6” Extension 3/8” Drive, I used two.- 3/8” to 1/4” Bit Driver for a hand drill.- Skill Drive 18 Volt Electric Drill.- Safety Goggles, no brand specific.- Safety Gloves any brand will do.Chemicals I Used:- Permatex Anti-Seize Compound P/N: 81343.- PB Blaster Penetrating Oil.Consumable I Used:- Paper Towel.Hope this helps Yall! If you found the video helpful please give it a thumbs up. If you’d like to help my channel please subscribe, even if you don’t come back it helps. Best Wishes & Blessings. Keith Noneya
Jessicas Family restaurant Williams AZ Keith Noneya 2021-06-21 | Hi folks this is a quick look at Jessica's Family Restaurant in Williams Arizona, the "Gateway to the Grand Canyon". It serves; American, Greek & Italian food. Going East on RT 66 it's past Safeway and the Highlander Motel on the the right as you come into town.When we pass through Williams on the way to see my dad we stop in town to visit Gregory and his restaurant. The food is really good and the decor is typical western 50-60's style. The staff is always friendly and helpful. However I must warn you that you may take a liking to Gregory if you meet him. He's one of the nicest folks I've ever met. The only bad thing about Greg's restaurant is the same problem with ALL the restaurants in Williams during Tourist Season, the cost. The average cost of breakfast or any meal in town after tax and tip is 20-30 a plate. We paid $21.00 a plate here and that's on par with the rest of the town, so if you're going to eat in Williams bring your wallet, you'll need it, I'm not joking Williams is expensive, especially the Pine restaurant! Well I hope you guys enjoy the quick video Best Wishes & Blessings. Keith Noneya
My Cat likes playing with a Laser Pointer Keith Noneya 2021-05-25 | My cat begs me almost every day to play with the Red Fly, or as we know it a little red laser. she gets really active chasing this thing around. Hope you all enjoy the cat fun. Best Wishes & Blessings. Keith Noneya
TLA 5204 No Display Fix Part 2 Bios & Software Keith Noneya 2021-03-08 | Description: Part 2 is me showing how to use an external display to access the BIOS and change settings. The unit PS2 ports are not working, but the USB ports are. So I used a USB Mouse and Keyboard along with an external display to access the Bios and run some of the WIN 2K Diagnostic Tools. Enjoy the links below.- Part 3, we will open it up and change the BIOS battery and ensure the settings remain after the power is cycled. - Part 4 and later, if I have them, will be a complete tear it down, we’ll look at the board Part Numbers and give it a good cleaning.- Part 5 will be reassembly and power up.- Part 6 will be to test it on a DP 8200 Reference DC & Current Calibrator that I fixed in another series of videos here: youtube.com/watch?v=hQq0_wkzGTo&list=PLVLXGvrQp0Ou1W3UZmFQkQG6BMcSyMYKtHelpful Links:- A quick Fix project to repair fourteen TLA5202’s with no display: http://www.dasarodesigns.com/projects/a-quick-fix-for-tektronix-tla5000-series-logic-analysers- A HOW TO UPGRADE YOUR TLA 5200 Series Logic Analyzer: eevblog.com/forum/testgear/tektronix-tla5202-5202-series-posterity-information-hacks- TLS Application Software Version 4.4: http://www.dasarodesigns.com/schematics-and-resources/?drawer=files*Tektronix*TLA5000- TLA 5200 Series Logic Analyzers; A Quick Start Users Manual 071-1575-00 Here: https://engineering.purdue.edu/~ece437l/papers/tla5201qs.pdf - TLA 5200 Series Service Manual here: tek.com/tla5201-manual/tla5000-series-service-manual - P6417, P6418 Logic Analyzer Probes Here: tek.com/manual/p6417-p6418-logic-analyzer-probes - More TLA 5204 Manuals from Tektronix: tek.com/search?facets=_templatename%3dManual&keywords=tla5204 You may have to join Tektronix but it’s worth it! Or you can hunt around the web and hope the site you go to doesn’t have viruses. The links above I gave you are virus free at the time of this post.I hope this video series helps you in the repair and use of your TLA5000 Series Logic Analyzer. If you have links or schematics to the Acquisition Board, I’d really like to have a copy of them.If you learned something, please give the video a Thumbs up for all the time and research that went into producing them. If you would like to help my channel, even if you don’t come back, please subscribe.Best Wishes & Blessings. Keith Noneya
Tektronix TLA 5204 No Display Fix Part 1 Unboxing Keith Noneya 2021-02-09 | Description: Part 1 is my unboxing of a TLA 5204 with NO display. It’s a quick introduction of what it is and what came with it. Also included are some helpful links and the mother board part number. See bottom of Description.Future videos in work…… Should be able to get 1 up every two weeks.- Part 2, "In Work!" Will show how to use an external display to access the BIOS and change settings. Almost complete.- Part 3, We will open it up and change the BIOS battery and ensure the settings remain after the power is cycled. **** Future Planned Videos: ****- Part 4 and later, if we have them, will be a complete tear it down, we’ll look at the board Part Numbers and give it a good cleaning.- Part 5 will be reassembly and power up.- Part 6 will be to test it on a DP 8200 Reference DC & Current Calibrator that I fixed in another series of videos here: youtube.com/watch?v=hQq0_wkzGTo&list=PLVLXGvrQp0Ou1W3UZmFQkQG6BMcSyMYKtHelpful Links:- A quick Fix project to repair fourteen TLA5202’s with no display: http://www.dasarodesigns.com/projects/a-quick-fix-for-tektronix-tla5000-series-logic-analysers- A HOW TO UPGRADE YOUR TLA 5200 Series Logic Analyzer: eevblog.com/forum/testgear/tektronix-tla5202-5202-series-posterity-information-hacks- TLS Application Software Version 4.4: http://www.dasarodesigns.com/schematics-and-resources/?drawer=files*Tektronix*TLA5000- TLA 5200 Series Logic Analyzers; A Quick Start Users Manual 071-1575-00 Here: https://engineering.purdue.edu/~ece437l/papers/tla5201qs.pdf - TLA 5200 Series Service Manual here: tek.com/tla5201-manual/tla5000-series-service-manual - P6417, P6418 Logic Analyzer Probes Here: tek.com/manual/p6417-p6418-logic-analyzer-probes - More TLA 5204 Manuals from Tektronix: tek.com/search?facets=_templatename%3dManual&keywords=tla5204 You may have to join Tektronix but it’s worth it! Or you can hunt around the web and hope the site you go to doesn’t have viruses. The links above I gave you are virus free at the time of this post.I hope this video series helps you in the repair and use of your TLA5000 Series Logic Analyzer. If you have links or schematics to the Acquisition Board, I’d really like to have a copy of them.If you learned something, please give the video a Thumbs up for all the time and research that went into producing them. If you would like to help my channel, even if you don’t come back, please subscribe.Best Wishes & Blessings. Keith Noneya
2003 - 2017 Murano Antenna Change AntennaMastsRus Keith Noneya 2021-01-17 | Description: If your antenna is broken off, don’t sweat it. Go the store or your favorite online store and purchase one. Get a step stool and twist the old one off and screw a new one on. The cost will depend on the length, who makes it and where you buy it. Here’s some helpful information.Part I used: - AntennaMastsRus PN A058-4 Approx. $17.99 ( Fits 2003-2017 Nissan Murano ). You don't have to use this Part Number or Brand. If it fits it will work.Tool I used: - Step stool.Hope that helps someone. Thanks for watching. Best Wishes & Blessings. Keith Noneya
How to remove Permanent Marker from metal and plastics Keith Noneya 2021-01-09 | Hi folks, you can remove all or most of permanent marker from metal and plastics if you soak it with, 90% or higher, Isopropyl Alcohol and then rub it with a paper towel. If it's a little stubborn you can use an acid brush with half the bristles cut off and scrub it. Although it's not always recommended you can also use Brake Cleaner, Goobegone or Carburetor Cleaner as well. Only when using the last chemicals listed you have to get on and off quickly or the chemicals can eat or soften the plastics or painted areas. Hope this little tip helps you folks. Please give the video a thumbs up if you learned something.Thanks for watching. Best Wishes and Blessings. Keith Noneya
Mesa Boogie Fillmore 25 Reverb Box Inspection & Repair Keith Noneya 2020-12-05 | How to test, diagnose and repair your Reverb Box on a Mesa Boogie Fillmore 25.Applies to most Mesa Boogie Reverb Boxes.Here's the link to the Mesa Boogie website on; "How can I test to see if my Reverb Tank is bad?" instructions.mesaboogie.zendesk.com/hc/en-us/articles/216605608-How-can-I-test-to-see-if-my-Reverb-Tank-is-bad-There are quite a few different ohms on the coils so get the one that matches yours, or get authorized service technician to order the part for you. Hope this helps you figure your amp out. Thanks for watching. If the video helped please give it a thumbs up. If you want to help my channel, even if you never come back, please subscribe. Thanks for watching.Best Wishes & Blessings. Keith Noneya
How to repair Corroded Or Battery Damaged pads & Chips Ie Packard Bell PB422TA 486 Keith Noneya 2020-11-27 | Description: This is how I repair corroded pads, via’s, runs & IC’s on circuit boards. The board I’m repairing is a mother board out of a Packard Bell 486 Model No. PB422TA. On the PB410 486 Motherboard, P/N: PY4307-03, the battery acid has leaked out and corroded U49 and several other surface mount components, including the pad, via’s and runs. Circuits get corroded for a variety of reasons, battery acid, water intrusion and flux left on the board that absorbs water and eats the components. The process applies to any corroded circuit board. Here's a link to the website my friend used to troubleshoot his PB. There's some useful info here:erickenny.wordpress.com/2019/10/27/resurrecting-a-packard-bell-486Here's My friend Saun's channel: SIMPLETHINGSTOYS youtube.com/channel/UCLxoVzIzuIN1tQ7DRO7gB6gItems I used:- Round Nosed Exacto Blade.- Solder Wick, small.- Lead 70/30 Solder. .020”- KimWipes or TekLites. Technical Towelettes.- Liquid RMA Flux.- Isopropyl Alcohol. to clean the flux off the board and IC.- Small Side cutters, to cut the wick.- Electronics Micro-Scope and stand with a LED Ring Light.- A No. 80 drill bit to clean the corrosion out of the via holes.Hope this helps Yall! If you liked the video or learned something, please give it a thumbs up for my efforts. If you would like to help my channel, please subscribe. I do electronics, misc. computer stuff and automotive repairs. Thanks for watching. Best Wishes & Blessings. Keith Noneya
1999-2004 Ford F250 F350 7.3L Drivers Dual Battery Change Motorcraft BXT 65 850 Keith Noneya 2020-10-09 | How to change your Driver's Battery on the F250 F350 7.3L with some tips and tricks on battery terminal treatment and diagnostics.Ford 7 3L F250 F350 Passenger Battery Change Step by Step W Tips here; youtube.com/watch?v=ZFnkOufsXQg&t=11sPart I used: Battery Group Size 65 850 Cranking Amps- Motorcraft BXT 65 850Alternate Parts:- Duralast Gold Battery 65-DLG- Champion 65-850CHPTools I Used:- 1/2" Combination Wrench- 12mm Combination Wrench- 1/2" Deep Socket 3/8's Drive- 12mm Deep Socket 3/8's Drive- 3/8's Drive Stubby Ratchet Harbor Freight- 8mm socket 3/8's Drive- 3/8's Drive Wobble 6" extension Harbor Freight- Battery Terminal Cleaner Tool- Small Digital Voltmeter Actron CP7672- Large Screw Driver- Small Wire Brush- Paper TowelsOptional Tools but recommended:- Battery Charger- Battery Load Tester- Battery Hydrometer Lead Acid TesterChemicals Used:- Soda Pop- Battery Terminal Protector CRC No. 05046- Anti-Seize Compound Permatex 81343Thanks for watching. Please give me a thumbs up if you learned something or found the video helpful. If you would like to help my channel, please consider subscribing. Best Wishes & Blessings. Keith Noneya
Cat begging for a snack Keith Noneya 2020-10-07 | Every time my cat wants a snack she comes over and starts putting on this show or she will jump up on the chair arm and start head budding my hand. If you ignore her long enough she will start climbing on the back or your chair and get so obnoxious that you can't ignore her anymore. I just happen to catch her doing it so I thought I would share it with all of you. Thanks for watching. Best Wishes & Blessings. Keith Noneya PS she did get her snack!
Tektronix CG5001 eBay Unboxing Keith Noneya 2020-09-05 | Description: I purchased this off eBay in unknown condition for around $280.00 after shipping and taxes. They are primarily used to calibrate Oscilloscopes and for an older series TM piece of equipment have a distinct advantage over the earlier TM series calibrators in that they are GPIB compatible. I was particularly glad to get the unit for a reasonable price as repaired and Calibrated they can go for as much as $3,000.00. In working condition they normally go for around $1,200.00 I plan to disassemble the unit and repair it then put it in my collection of TM series equipment.If you have information on it please pass it along to me at my YT email.Keith_Noneya@att.net Would love to see some videos on this being used particularly with GPIB. Thanks for watching. Best Wishes & Blessings. Keith Noneya
Lighting Strike Damage on a tree Aug 2020 Keith Noneya 2020-08-23 | Description. This tree took some serious damage as a lightening bolt hit some time on the 13th of August 2020 around 2:40. The heat from the bolt caused the tree to steam up inside and the pressure from that steam caused the tree to explode. The tree split into about three main pieces that went up about 30 feet from the base . The pressure and explosion was so great inside that in addition to it splitting the tree it blew a branch off and threw debris up to 50 feet away. Hope you enjoyed the video. Best Wishes & Blessings. Keith Noneya
Tektronix 2465B Inidcators Flicker & Dianostic Routines Keith Noneya 2020-08-19 | Description: Just a quick video to address if the light indicators flicker when the control buttons are pushed & how to access the Diagnostic Routines particularly Hours On and Power ON/OFF Cycles.Manual used in the video is Tektronix Service Manual No. 070-6863-01 for the 2445B/2465B Oscilloscopes. Hope you enjoy the video. Best Wishes & Blessings. Keith Noneya
Ford F250 F350 7 3L Belt Tensioner Step by Step Gates 38191 Keith Noneya 2020-07-20 | Description: This video is how to change your 1998 to 2003 F250 - F350 7.3L Tensioner. It’s a Step by Step instructional with some tips on: Tools, P/N’s, Price and Misc. info.Part I used:- Belt Tensioner Assembly Gates 38191 $51.40 Ford/Motorcraft Part Number is: BT-50.Alt Part Numbers: Duralast 305257, Dayco 89257, Litens 999054A, ACDelco Pro 38191, Gates 38191If you wish to just change the pulleys use: - Ribbed: P/N: Dayco 89057 $14.99 to $46.91.- Smooth: P/N: Dorman 419-612 $13.50 to $24.99.If you wish to just change the bearings inside the pulleys use:- Sealed Bearing P/N: 6203-2RS, $10.00 for two. Note you’ll have to know how to do this without warping the pulley’s themselves. Use a digital caliper to ensure the old bearing dimensions are: ID-17 mm x OD-40 mm x Width-12 mm if using the 6203-2RS. Most Idler Pulleys us the 6203-2RS but ensure the old pulley dimensions are correct prior to ordering them.Tools I used: Note you can RENT most of these tools from AutoZone or another Parts Store.- 1/2” Torque Wrench, capable of 35-45 ft. lbl’s. $37.00-$55.00 for a cheap one.- 1/2” Braker Bar.- 1/2" to 3/8” Drive Adapter.- 13 mm 3/8” or 1/2" Drive Deep Socket.- 13 mm 3/8” Drive Socket.- Stubby or Palm 3/8” Drive Ratchet.- Folding Heavy Duty Tire Step by Powerbuilt Part No. 647596 amazon.com/Powerbuilt-Non-Slip-Surface-Adjustable-Storage/dp/B0002Q8TWI $40.99 or- Folding Step Stool, Rubbermaid EZ Step P/N: FG420903 $31.99 to $48.99.- Mechanics Shade Tarp. Home Build it here: youtube.com/watch?v=9A6Y85cy-jg&feature=youtu.beIf you enjoyed or learned something, please give the video a thumbs up. If you would like to help my channel, please subscribe. Ring the bell if you would like to be notified when I put out new videos.Thanks for watching. Best Wishes and Blessings. Keith NoneyaCompressor viewing condenser moisture install accumulator description Evaporator
2014 Murano Proper Battery Change Step By Step with Corrosion Control Keith Noneya 2020-07-13 | How to change a battery in most Murano's or other vehicles. This video includes a little bit on how to deal with corroded battery terminal clamps.Part I used:- 12vdc Duralast Platinum Battery 35-AGM Group Size 35 650 CCA $199.99.Chemical I used:- Bottle of Soda Pop, to clean battery acid corrosion off Battery Terminals.- Battery Terminal Protector By CRC #05746 $6.99.- Mr. Clean in a spray bottle.- Automotive Natural Orange Pumice Hand Cleaner By GoJo #0951-15 $11.69.Tools I used:- Beach Towel to protect the vehicles carpet during transportation.- 10mm 3/8" Drive Deep Socket.- 3/8" Drive Stubby/Short or Palm Ratchet.- 10mm Ratchet Combination Wrench.- Small Wire Brush, to clean battery acid corrosion off Battery Terminals.- Bullet Battery Terminal Brush Cleaner. $5.99.- Small Multi-Meter to check battery voltage.- Paper Towels/Rags.Here's the video on how to jump your Nissan when It won't turn over and the cables are on the battery.youtube.com/watch?v=4BzLNYX9NFoHope this helps some folk. If you learned something or liked the video please give it a thumbs up. If you would like to help my channel please subscribe.FREE! Complete Factory Service Manuals if you join the NICO CLUB, it's free.*** After you create an account and password. *** [ Then select "Service Manuals" on the right of the header, then on the left in Red, select "Nissan Factory Service Manuals" Link here: nicoclub.com/nissan-service-manuals.Thanks for watching. Best Wishes & Blessings. Keith Noneya
1995 Pathfinder D21 No Dash Lights No Crank Fusible 2402201G00 Link Fix Part 2 Keith Noneya 2020-06-27 | This is a long video on how to do a short term or long term repair the Fusible Links on a 80-90's Nissan D21 truck or Pathfinder. I'm sure it applies to most Nissan's of that era. I take you from how to find out if it's bad to how to carefully pull it apart and fix it with new Fusible Link wires or temporary wires of the same gauge. The wires I used in this video are temporary and should NOT be used long term. The reason is not that the gauge is wrong, it's that the jacket is NOT designed to hold the fire and melted wire internally. IF you don't use the correct fusible link wires the jacket can catch on fire when it melts and theoretically catch something else on fire in the engine compartment. So change it as soon as practical. Also monitor them for signs of over heating until you can change them out.The video is long so just skip through the parts to the ones you want to see. You can buy complete wired units on eBay or the dealer if you can find the part number. The part number for the 1995 Nissan D21 or Pathfinder is 2402201G00.Thanks to a astute comment from YouTuber "Kenabi", who informed me about Color Coded Fusible Link wires. So I looked them up, I now know about them, and I'm passing the information on to you. - Learn about them here: lifewire.com/car-fuses-and-links-explained-4018163- Learn more about them here: awcwire.com/allied-university/informatic/fusible-links- Learn more & Order them or connector parts here: whiteproducts.com/downloads/WhiteProductsCatalog.pdfPart 1 of the video on how I discovered it is here; studio.youtube.com/video/A51r0wbxV-o/edit ****** Note ****** that NISSAN in 1995 did NOT follow these color codes so you will have to determine on your own what fusible link amperage you need, then order it, Note the color will be different from what the vehicle originally came with since Nissan did NOT use the same color code as used today. It is my recommendation that you just replace it with the correct fusible link as soon as possible.FREE! Complete Factory Service Manuals if you join the NICO CLUB, it's free.*** After you create an account and password. *** [ Then select "Service Manuals" on the right of the header, then on the left in Red, select "Nissan Factory Service Manuals" Link here: nicoclub.com/nissan-service-manuals.Hope it helps someone. I keep my word Kenabi, Thanks for your help. If you learned something please give the video a thumbs up. If you would like to help the channel please subscribe. Best Wishes and Blessings. Keith Noneya
How to tell if your Nissan CVT is going bad 2014 Murano Slipping Keith Noneya 2020-06-03 | Finally fixed, with a re-manufactured transmission.*** Update 22 June 20: St. Tammany Transmission attempted to service and just change the Stepper Motor out, as I requested, and it still had problems with slippage. So that means that the Pressure Regulator valve or the little balls on the pulley shafts were binding up or both. So I had to change it out with a re-manufactured transmission, NOT REBUILT. They did not charge me for the Service but did charge me the $150.00 for the Stepper Motor and that is more than fair. I asked them to try the service and stepper motor at a approximate cost of $389.00 plus tax. So they ended up eating the fluid and filter and I ended up eating the Stepper Motor, which I assume they would keep clean up and re-use, a fair trade. The total cost of the transmission and the stepper came out to $4,077.00 dollars with a 36 month 50,000 mile warranty. If you knock off the $150.00 that's $3,927.00. Really not bad, as the dealer wanted $5,200.00 to put a new one in, with the same warranty. Lesson learned, DON"T SKIP THE TRANSMISSION SERVICE ON YOUR CVT & don't drive it like a dragster jumping off the line at the drag races. ** Update 11 June 20: I had St. Tammany Transmission facebook.com/AsapSTTammanyTransmission take a look at them. They pulled the pan and found virtually almost no metal shavings at all in it. I told them as soon as it gave me trouble I babied it home, NOT over revving it, meaning when I saw the revs going up I backed off the throttle. They said that probably prevented the tranny from excessive damage and probably saved the rest of it. The pulled the code 1776 on it and the computer said the Stepper Motor was bad. So they are going to service the transmission, put a Nissan Stepper in it and see if that fixes it. I should find out around Tuesday afternoon.* Update 03 June 20: Nissan of Slidell says I need a new transmission, $5,200.00 dollars. Oh nooooo!!!So I'll look into getting it rebuilt or look around for a good used one. I'll keep you all informed of what I find out!This is my 2014 Murano on the way home from work I was driving at approximately 70 mph. Take note of the tachometer, the RPM's slowly changing up and down between 2K & 4K. Here are some more symptoms: 1. The transmission does not want to move or moves slow from a dead stop, like pulling out from a stop sign it doesn't want to move. It acts like it's in neutral at first then slowly pics up speed.2. Once it starts to move it almost drives normal except RPM's vary.3. Once moving pressing harder on the accelerator the transmission acts like its shipping or moving into a lower gear. Meaning the RPM's go up but the car doesn't go faster right away.4. If you take off to fast you'll get a couple of big bumps from the acceleration.- What to do if you have these symptoms:A. Gently, not over revving it, take it home and PARK IT IMMEDIATELY. B. Set up an appointment with a transmission shop, NOT the dealer! The dealer will tell you it can't be fixed, IT CAN in some instances. C. If you didn't tear it up and keep driving it you MAY get by with:- A service & a Stepper motor replacement, about $400.00 dollars vice $4,000.00 non-dealer replacement, or a $5,700.00 dealer new transmission.- A service & a Solenoid Pack replacement. about $1,200.00 D. If you tear it up some but not to bad it will need a rebuild, or a refurbished transmission. They run anywhere from $3,600.00 to $4,200.00 depending on who you have do it.E. If you tear it up beyond repair by driving it and over revving it, you'll have to replace it. That will cost you around again, $3,700.00 to $5,700.00. F. You may get a used one from the junk yard for around $1,200.00 plus shipping.G. You can rebuild it yourself for around $1.500.00 to $2,200.00 depending on how bad you tore it up. That's provided you have the skills and tools to do the job. Price listed included the special tools.FREE! Complete Factory Service Manuals if you join the NICO CLUB, it's free.*** After you create an account and password. *** [ Then select "Service Manuals" on the right of the header, then on the left in Red, select "Nissan Factory Service Manuals" Link here: nicoclub.com/nissan-service-manuals.See an overview of the Nissan CVT Lawsuit here: topclassactions.com/lawsuit-settlements/closed-settlements/931402-nissan-transmission-class-action-settlementThanks for watching, I hope this helps someone. Best Wishes and Blessings. Keith Noneya
MPC 1000 Q-Link Slider Repair Keith Noneya 2020-05-25 | Description: The MPC1000 is an awesome mixing unit capable of just about any audio voice or music arrangement you can think of. Much of today’s Digital Music is produced with one of these or a unit just like it. In this video we repair the Q-Link Slider on the bottom left. It’s the same for both sliders so if you do one the other is the same. Sorry I don’t have the part number for a replacement slider. However, if you type into google “AKAI MPC 1000 potentiometer Q-Link” some replacements will show up. They normally run from $9-15.00. They are also on eBay for about the same price. This repair was for a friend of mine on YouTube “SIMPLETHINGS”: In this video series there's also a video repair of the “MPC 1000 DATA Wheel Encoder Mitsumi SIM 026MT R66 5214 Repair there’s no direct replacement for the original Encoder SW101, a Mitsumi Switch Encoder SIM-026MT Part Number: R66 5214. The Mitsumi Encoder SIM-026MT Data Sheet. Tools used:- Hobby knife, Ace Hardware.- 1-1/2” Needle Nose Pliers. Any brand will do, I used Craftsman for this job.- 30 watt soldering iron will do.- 4” Side Cutters, used for cutting the braid.- Acid brush, with 1/2 of it cut off with a pair of scissors.Consumables Used:- Isopropyl Alcohol, 90%- Liquid Flux.- 70-30 Lead/Tin Solder.- Solder braid, medium, to remove & clean the pads, once removed.- Paper Towels.Documentation:- AKAI MPC1000 Website: http://www.akaipro.com/products/legacy/mpc-1000You can get the Operations manual there and some other information.- Service manual: http://www.synfo.nl/servicemanuals/Akai/MPC1000_SERVICE_MANUAL.pdfLinks to the OP & Service manuals and Org Encoder Data Sheet will be linked at the bottom.Alternate Part and Board Mod repair here: mpc-forums.com/viewtopic.php?f=15&t=180203MOD Encoder by ALPS P/N: EC12E24204A2 ~$6.00 on eBayNew Operating JJ Software for mod here: http://www7a.biglobe.ne.jp/~mpc1000/faq.htmComplete NEW BOARD By MPCSUFF HERE: mpcstuff.com/mpc-1000-right-side-pcb-board-w-volume-and-jog-upgraded ~ $139.00The MPC1000 was purchased from Ras David Fishe at OscillationCommunications in New Orleans, a talented local artist. Some of his music was produced using this very unit we repair in the video.Here’s some links to websites if you’re curious: soundcloud.com/oscillationcommunications.facebook.com/OscillationCommunicationsmusictech.net/2017/02/studio-interviews-oscillation-communicationsyoutube.com/channel/UCN0US5AbfgtOXNRw92XhwtwHope this helps. If you learned something useful please give me a thumbs up for the time spent doing it for you. If you’d like to help my channel please subscribe, even if you don’t come back again. Best Wishes n Blessings. Keith Noneya
Buddy the Feral Cat Loves His Head Scratch Keith Noneya 2020-05-09 | This is Buddy. He showed up at the back door as a kitten. We fed him and he became very tame, as Feral cats go. After awhile he would come in when we opened the door, jump up in your lap and beg & meow for you to pet and give him a head scratch. He was a huge cat. We loved that cat. Unfortunately we think someone abused him and poisoned Him. He showed up delirious one day and we couldn't catch him for a vet trip. He ran off staggering and we never saw him again. Be nice to those outside kitties they may end up being a real treat in life. They kill rodents, and bugs as well. If they get to be a bother your local Animal Control can loan you a trap with a deposit that will be refunded when you bring the cage back. Thanks for watching. I hope you find your little Buddy in life. Best Wishes & Blessings. Keith Noneya
95 Pathfinder D21 No Start Crank or Dash lights Fix Most Likely Solution Part 1 Keith Noneya 2020-04-06 | If you have No Dash lights, No crank, No Start & the truck is dead, check these wires and fuse. I'll post a follow up video on how to repair the wire assembly when I get a chance. - Depending on your year do this search " Nissan Link Fusible " (make sure you put Link BEFORE Fusible), and by the one that looks like yours. You should be able to find the harness you need.Part 2 on how to temporarily fix the link until you can get a replacement is here: youtube.com/watch?v=cqSSOlzrRk4- FREE! Complete Factory Service Manuals if you join the NICO CLUB, it's free.*** After you create an account and password. *** [ Then select "Service Manuals" on the right of the header, then on the left in Red, select "Nissan Factory Service Manuals" Link here: nicoclub.com/nissan-service-manuals.Please give the video a thumbs up if you learned something. If you want to help my channel grow, please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya
How to Detect Low AC pressure Easily Ie F250 or F350 Keith Noneya 2020-04-04 | Don't have the equipment to check, no problem, here's a quicky vid on how to check for low refrigerant in your truck or car. There are a lot of things in an AC systems that can cause it to work improperly, but LOW refrigerant is the most common. It’s, & USUALLY the easiest to fix, even for the common person. This video is a quick guide and is NOT intended to cover EVERY possible problem. It's the quick & dirty check for the average person who doesn't have hundreds of dollars of equipment. The major cause of Low Refrigerant is a slow leak. ALL systems leak a little but over time they should last for 5-10 years before it leaks down enough to cause problems. "IF" the system has NOT been opened, lines disconnected, you can most of the time use a quick charge kit and you’re good to go. “IF” you opened the system, lines disconnected, you''ll most likely have to pull a vacuum on it AFTER you replace the seals, and Dryer/Accumulator. After repairs, make sure and do a good inspection on the lines and joints where the system connects together. You'll want to look for a dark oily area covered with dirt, or an area that is bright green. If you find such an area, change the seal or that component. The Condenser behind the grill if it gets hit with a large sharp rock can easily be punctured and you'll see that dark dusty oily area where the seal was broken and the refrigerant leaked out. Anyways do your homework BEFORE removing any parts. YOU CAN RENT vacuum pump and an AC gauge set to do the job correctly. Some Automotive stores like AutoZone will rent them for FREE!. You put down a deposit on the equipment and when you bring it back you get ALL of our deposit back! If you open a system replace the dryer/accumulator to be safe, as a minimum. If you just opened it for part of the day and you have already replaced it, you can just pull a vacuum and it should be good. Hope this helps point you all in the right direction. If you learned something please give the video a thumbs up and if you would like to help my channel, please subscribe. * On a side note. Go check out the comments for Mike Smith below. Some GOOD info there as well.** I'm working on a series on how to completely rebuild the AC system by replacing EVERY item in the engine bay related to the AC System. I shot the videos already, I just need to edit them!*** I'll show how to: - Replace ALL the components under the hood.- Find & test for leaks.- Pull a vacuum. - Recharge it. - List ALL the Part Numbers.- Where to find the parts cheap and get access to the tools WITHOUT BUYING THEM! Thanks for watching and glad to help. Best Wishes & Blessings. Keith Noneya
1999 to 2004 Ford F250 or F350 Grill Removal a How To Keith Noneya 2020-04-02 | How to remove your F250 or F350 Grill. This allows better access to the components behind it. Like the Condenser, Radiator, Fog Lights & the Transmission Cooler. Thanks for watching. If you learned something please give me a thumbs up for the time a spent making it. If you would like to help my channel please feel free to subscribe. Best Wishes & Blessings. Keith Noneya
Tektronix 24XX Series Cover Removal Keith Noneya 2020-04-01 | WARNING there are very high voltages inside 2,000 volts or 2KV for short. These are LETHAL voltages!NEVER leave a scope unattended with children or pets around and the cover removed or the with the power applied to it!Also if you are not an experienced electronics technician get someone who is familiar with servicing equipment that has high voltages present before removing any internal shields! *** Update: *** The jumper at time index 4:08 through 4:33, is not the CAL Jumper, it's actually in the top left corner of the same board, as it was a SN above B050000. You can find it in the 2445B through 2467B manuals on Fig. 10.5a & b. Location of the jumper depends on SN. The name may be either J501 or P501 depending on SN. Sorry for the oops! Thanks Manuel Meseda who commented on the location error. (The jumper in the slide show is correct for SN's B049999 and below.)*** Description: How to remove the cover on a 2400 Series Oscilloscope with some CAL and Maintenance Notes. If you learned something please give the video a thumbs up. If you would like to help my channel please subscribe. Best Wishes & Blessings. Keith Noneya
Husqvarna 224L Honda GX25 35 Rocker Arms Keith Noneya 2020-03-29 | Description: Quick NOTE I got the feeler guages backwards in the video.Other than that all is good, and it runs fine even if I got them backwards. This video is about removing the Rocker Arms on a Husqvarna 224L or a Honda GX25/GX35 Weed Wacker Engine. This engine is used in several Honda and Husqvarna equipment lineups.For manuals see this link. rentamaxcr.com/content/9-soporte-tecnicoYou may have to use your browser to translate the web page. However, the manuals are in English after you download them. Tools needed are:- 4mm Allen Wrench- 2.5mm Allen Wrench- 8mm Combination Wrench- Feeler Gauge Set .003” & .004” (KD Tools No. 162)- 1Lb Hammer- 3Lb Hammer- 3/16” Flat Punch- ¼” Flat PunchParts that may apply:- Honda 25cc Rocker Arm Kit PN: 14730-Z0H-000 approx. $8.00 - $15.00 USDChemicals Needed:- Solvent to clean Valve Stem Seal: Isopropyl Alcohol or Brake Clean.Consumables Needed:- Shop rag or Paper Towels.Thanks for watching. I hope you found the video useful. If you did please give it a thumbs up and if you want to really help my channel, please subscribe. Best Wishes & Blessings. Keith Noneya
2003-08 CTS Brake Caliper Rebuild Part 1 Caliper & Piston Removal Keith Noneya 2020-02-22 | Description: WARNING!!!! Working on brake systems is CRITICAL to vehicle safety. If improperly done it can lead to serious injury or death to you or others. KNOW what you are doing before working on any part of your braking system. If you don't, consult a professional or someone who is familiar with the proper maintenance and repair of the Braking systems. Your life and others with depend on that! This video series is intended to assist professionals or people familiar with the systems. If you are not, DO NOT attempt this procedure, then this video is for entertainment purposes only.Centric Caliper Repair Kit - Front P/N: 2768-05106972 $8.18 Part 2 is here: youtube.com/watch?v=bkJ7fyYSGoIPart 3 is here: youtube.com/watch?v=0FUhgSl035QPart 4 is here: youtube.com/watch?v=jAFGs8X_iFQPart 5 is here: youtube.com/watch?v=EORM8bSkm8kIf you learned something or found the video useful, please give the video a thumbs up for all the hours I put into it. If you want to help my channel more, please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya
2003-08 CTS Brake Caliper Rebuild Part 2 Hole resizing Keith Noneya 2020-02-22 | Description: WARNING!!!! Working on brake systems is CRITICAL to vehicle safety. If improperly done it can lead to serious injury or death to you or others. KNOW what you are doing before working on any part of your braking system. If you don't, consult a professional or someone who is familiar with the proper maintenance and repair of the Braking systems. Your life and others with depend on that! This video series is intended to assist professionals or people familiar with the systems. If you are not, DO NOT attempt this procedure, then this video is for entertainment purposes only.Centric Caliper Repair Kit - Front P/N: 2768-05106972 $8.18 Part 1 is here: youtube.com/watch?v=MoiZX6qYXGQ&t=2sPart 3 is here: youtube.com/watch?v=0FUhgSl035QPart 4 is here: youtube.com/watch?v=jAFGs8X_iFQPart 5 is here: youtube.com/watch?v=EORM8bSkm8kIf you learned something or found the video useful, please give the video a thumbs up for all the hours I put into it. If you want to help my channel more, please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya
2003-08 CTS Brake Caliper Rebuild Part 3 Reassembly Keith Noneya 2020-02-22 | Description: WARNING!!!! Working on brake systems is CRITICAL to vehicle safety. If improperly done it can lead to serious injury or death to you or others. KNOW what you are doing before working on any part of your braking system. If you don't, consult a professional or someone who is familiar with the proper maintenance and repair of the Braking systems. Your life and others with depend on that! This video series is intended to assist professionals or people familiar with the systems. If you are not, DO NOT attempt this procedure, then this video is for entertainment purposes only.Centric Caliper Repair Kit - Front P/N: 2768-05106972 $8.18 Part 1 is here: youtube.com/watch?v=MoiZX6qYXGQ&t=2sPart 2 is here: youtube.com/watch?v=bkJ7fyYSGoIPart 4 is here: youtube.com/watch?v=jAFGs8X_iFQPart 5 is here: youtube.com/watch?v=EORM8bSkm8kIf you learned something or found the video useful, please give the video a thumbs up for all the hours I put into it. If you want to help my channel more, please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya
2003-08 CTS Brake Caliper Rebuild Part 5 Bleeding Brakes Keith Noneya 2020-02-22 | Description: WARNING!!!! Working on brake systems is CRITICAL to vehicle safety. If improperly done it can lead to serious injury or death to you or others. KNOW what you are doing before working on any part of your braking system. If you don't, consult a professional or someone who is familiar with the proper maintenance and repair of the Braking systems. Your life and others with depend on that! This video series is intended to assist professionals or people familiar with the systems. If you are not, DO NOT attempt this procedure, then this video is for entertainment purposes only.Part 1 is here: youtube.com/watch?v=MoiZX6qYXGQ&t=2sPart 2 is here: youtube.com/watch?v=bkJ7fyYSGoIPart 3 is here: youtube.com/watch?v=0FUhgSl035QPart 4 is here: youtube.com/watch?v=jAFGs8X_iFQIf you learned something or found the video useful, please give the video a thumbs up for all the hours I put into it. If you want to help my channel more, please subscribe. Thanks for watching. Best Wishes & Blessings. Keith Noneya
Data Precision 8200 Repair It Works Part 5 Keith Noneya 2020-01-26 | Well I finally got it working. After I played around with the display board it started working and I couldn't get it to stop working like it was before. As far as the 100mv range it turns out other than the switches being intermittent the 100mv range was probably working all the time. Thanks to Bruno who commented on a few of the videos in the series, I found out the 100mv only comes out the back connector J301 (round one) pins 2 & 3, pin 1 being Guard. I also show the 100mv path up to the op amps and some mods I made to the schematic. Oh a quick note on the schematic at time index 17:28 thru 17:53 the Cathode of CR14 connects to V7 not V1, this has been updated in my latest schematics dated 12 Sep 21 and later. - One of my my viewers made a very detailed paper and analysis of this unit here; http://www.hhenkel.de/data-precision-8200/repair-8200.html - Copies of my reworked Digital schematics can be found here; http://www.ko4bb.com/getsimple/index.php?id=manuals - If you'd like my more up to date copies you can email me here; keith_noneya@att.netHope it helps someone. Thanks for watching. Best Wishes & Blessings. Keith Noneya
