Uploaded August 2023 | Updated September 2026, 1 week ago
In this video I will walk you through the installation of the XTOOL D1 Pro 40W laser upgrade. We will go from the unboxing all the way through assembly and onto processing sample jobs. I have tried to be as thorough and detailed as possible in this 40W setup guide and I even have new upgrades and accessories available for your XTOOL D1 Pro.
@xToollaser sent me the D1 Pro 40W model to test and I've been impressed with the power available in a 40W diode laser. In one of the sample jobs covered in this video I was able to cut through stainless steel shim stock as well as 19mm (3/4") plywood.
Haven't purchased your XTOOL D1 Pro yet? Check out the following links:
XTOOL D1 Pro 10W:
► xtool.com/products/portable-diode-laserbox-d1-for-laser-engraving-laser-cutting?ref=D5HpJRsyqyUUnt&utm_medium=null&utm_source=influencer
XTOOL D1 Pro 20W:
► xtool.com/products/portable-diode-laserbox-d1-for-laser-engraving-laser-cutting-b?ref=D5HpJRsyqyUUnt&utm_medium=null&utm_source=influencer
XTOOL D1 Pro 40W:
► xtool.com/products/40w-laser-module-for-d1-pro?ref=D5HpJRsyqyUUnt&utm_medium=5306&utm_source=influencer
In addition to the setup guide, I have also designed and made available a fume extractor nozzle to eliminate fumes at the source:
10W D1 Pro version:
► embracemaking.com/products/xtool-d1-pro-10w-fume-extraction-nozzle
20W D1 Pro version:
► embracemaking.com/products/xtool-d1-pro-20w-fume-extraction-nozzle
40W D1 Pro version:
► embracemaking.com/products/xtool-d1-pro-40w-fume-extraction-nozzle
Recently, I also added two more upgrades. A protective cover for the control board PCB and a cover for the main button so that it does not get accidently pressed, as well as the RA2 Rotary Switch:
► embracemaking.com/products/xtool-d1-pro-pcb-and-button-cover-kit
► embracemaking.com/products/xtool-ra2-y-axis-switch
If you're looking for the setup guide for the RA2 rotary attachment, you can find that one here:
► youtu.be/Znsc8WNEM04
And here is the RA2 Tilt Mechanism:
► embracemaking.com/products/xtool-ra2-pro-tilt-mechanism-kit
Finally, the LED lighting kit is ready!
Found here:
► embracemaking.com/products/xtool-d1-d1-pro-led-lighting-system
XTool D1 LED Installation here:
► youtu.be/jfeoCOW2r_0
If you are looking for products or items I've used with the D1 Pro in this video, see below. As an Amazon Associate may I earn from qualifying purchases (at no extra cost to you):
Adhesive Cable Tie Clips:
► amzn.to/3dTw4VS
CPAP Hose:
► amzn.to/3DmcxHF
Laser Proof Silicone Work Surface Mat (20" x 28")
► amzn.to/3zDyMG7
Laser Proof Silicone Work Surface Mat (23.5" x 31.5")
► amzn.to/3A0Fzv1
Electric Screwdriver:
► amzn.to/3JRbbZe
Feeler Gauges (For measuring depth of cut):
amzn.to/47BwJmi
If you want to go more in depth with the XTOOL Creative Space Software, check here:
support.xtool.com/hc/en-us/articles/6816833786519-Use-xTool-Creative-Space-XCS-to-Operate-xTool-D1-Pro
Always remember to practice proper laser safety. These lasers can seriously harm you directly (your eyes) or indirectly (your lungs and health). ALWAYS wear your safety glasses! By-products from processing certain materials can be toxic and harm you. DO NOT CUT vinyl materials like PVC. Check this list for hazardous materials before cutting something:
► wiki.atxhs.org/wiki/Laser_Cutter_Materials
Thank you @xToollaser
0:00 Intro
0:44 Unboxing
1:19 Disassembly
4:14 Assembly
9:17 Fume Extraction Adapter
12:04 Sample Jobs
16:41 Cutting Stainless Steel
18:30 How to (Not) Start a Fire
23:36 Laser Focus Offset
25:00 Cut 19mm Thick Wood
25:31 RA2 Rotary Attachment
33:04 Metal Business Cards
35:54 LED Lighting Kit
37:14 Outro
#laser #fume #xtool
****************************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► instagram.com/embracemaking
In this video I will walk you through the installation of the XTOOL D1 Pro 40W laser upgrade. We will go from the unboxing all the way through assembly and onto processing sample jobs. I have tried to be as thorough and detailed as possible in this 40W setup guide and I even have new upgrades and accessories available for your XTOOL D1 Pro.
@xToollaser sent me the D1 Pro 40W model to test and I've been impressed with the power available in a 40W diode laser. In one of the sample jobs covered in this video I was able to cut through stainless steel shim stock as well as 19mm (3/4") plywood.
Haven't purchased your XTOOL D1 Pro yet? Check out the following links:
XTOOL D1 Pro 10W:
► xtool.com/products/portable-diode-laserbox-d1-for-laser-engraving-laser-cutting?ref=D5HpJRsyqyUUnt&utm_medium=null&utm_source=influencer
XTOOL D1 Pro 20W:
► xtool.com/products/portable-diode-laserbox-d1-for-laser-engraving-laser-cutting-b?ref=D5HpJRsyqyUUnt&utm_medium=null&utm_source=influencer
XTOOL D1 Pro 40W:
► xtool.com/products/40w-laser-module-for-d1-pro?ref=D5HpJRsyqyUUnt&utm_medium=5306&utm_source=influencer
In addition to the setup guide, I have also designed and made available a fume extractor nozzle to eliminate fumes at the source:
10W D1 Pro version:
► embracemaking.com/products/xtool-d1-pro-10w-fume-extraction-nozzle
20W D1 Pro version:
► embracemaking.com/products/xtool-d1-pro-20w-fume-extraction-nozzle
40W D1 Pro version:
► embracemaking.com/products/xtool-d1-pro-40w-fume-extraction-nozzle
Recently, I also added two more upgrades. A protective cover for the control board PCB and a cover for the main button so that it does not get accidently pressed, as well as the RA2 Rotary Switch:
► embracemaking.com/products/xtool-d1-pro-pcb-and-button-cover-kit
► embracemaking.com/products/xtool-ra2-y-axis-switch
If you're looking for the setup guide for the RA2 rotary attachment, you can find that one here:
► youtu.be/Znsc8WNEM04
And here is the RA2 Tilt Mechanism:
► embracemaking.com/products/xtool-ra2-pro-tilt-mechanism-kit
Finally, the LED lighting kit is ready!
Found here:
► embracemaking.com/products/xtool-d1-d1-pro-led-lighting-system
XTool D1 LED Installation here:
► youtu.be/jfeoCOW2r_0
If you are looking for products or items I've used with the D1 Pro in this video, see below. As an Amazon Associate may I earn from qualifying purchases (at no extra cost to you):
Adhesive Cable Tie Clips:
► amzn.to/3dTw4VS
CPAP Hose:
► amzn.to/3DmcxHF
Laser Proof Silicone Work Surface Mat (20" x 28")
► amzn.to/3zDyMG7
Laser Proof Silicone Work Surface Mat (23.5" x 31.5")
► amzn.to/3A0Fzv1
Electric Screwdriver:
► amzn.to/3JRbbZe
Feeler Gauges (For measuring depth of cut):
amzn.to/47BwJmi
If you want to go more in depth with the XTOOL Creative Space Software, check here:
support.xtool.com/hc/en-us/articles/6816833786519-Use-xTool-Creative-Space-XCS-to-Operate-xTool-D1-Pro
Always remember to practice proper laser safety. These lasers can seriously harm you directly (your eyes) or indirectly (your lungs and health). ALWAYS wear your safety glasses! By-products from processing certain materials can be toxic and harm you. DO NOT CUT vinyl materials like PVC. Check this list for hazardous materials before cutting something:
► wiki.atxhs.org/wiki/Laser_Cutter_Materials
Thank you @xToollaser
0:00 Intro
0:44 Unboxing
1:19 Disassembly
4:14 Assembly
9:17 Fume Extraction Adapter
12:04 Sample Jobs
16:41 Cutting Stainless Steel
18:30 How to (Not) Start a Fire
23:36 Laser Focus Offset
25:00 Cut 19mm Thick Wood
25:31 RA2 Rotary Attachment
33:04 Metal Business Cards
35:54 LED Lighting Kit
37:14 Outro
#laser #fume #xtool
****************************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► instagram.com/embracemaking
