Uploaded October 2026 | Updated November 2026, 3 days ago
2007 Ford Explorer with an intermittent no-crank that finally became a hard no-crank condition.
Battery voltage was good, and the headlights stayed bright during the crank attempt, so we knew pretty quickly this wasn’t a simple battery problem.
From there, we went straight to the starter circuit and used nothing more than an incandescent test light to check the load side and control side of the starter circuit.
The rusty connections made this one interesting. At first, it looked very possible that we were dealing with a poor connection at the starter terminals. But instead of guessing or replacing parts based on appearance, we kept testing until we could prove exactly where the fault was.
In this video I cover:
• Basic no-crank testing
• Starter load-side and control-side checks
• Why a circuit must be tested under load
• Testing the stud versus the cable eyelet
• Identifying a voltage drop with a test light
• Separating a wiring problem from an internal starter problem
• Why rust alone doesn’t prove a bad connection
• Knowing when scan data is — and isn’t — necessary for a no-crank diagnosis
These are basic starting-system checks that technicians and DIYers can use on almost any vehicle.
The goal isn’t to guess whether the starter is bad. The goal is to prove it.
Want to learn electrical and electronic diagnostics from the ground up?
Join ScannerDanner Premium:
scannerdanner.com/join-scannerdanner-premium.html
14 Days for $1
On ScannerDanner Premium, you'll get:
*In-depth classroom lectures based on the material in my book
*Case studies with real vehicles brought into class
*Troubleshooting using proven diagnostic methods
*Access to our private forum
*Fundamental training in automotive electrical, electronics, and drivability diagnostics
📘 Want to Learn More About Diagnostics?
Check out my field manual, Engine Performance Diagnostics, available as both an eBook and paperback at:
👉 https://linktr.ee/scannerdanner
ScannerDanner Tools:
https://linktr.ee/scannerdanner
0:00 2007 Ford Explorer No-Crank
0:55 Starting Circuit Overview
1:47 Testing Power at the Starter
2:23 Why You Must Test the Circuit Under Load
3:29 Accidentally Making It Crank
4:32 Recreating the No-Crank Condition
5:25 Proving the Fault
7:51 Wiring Problem or Bad Starter?
8:18 The Tap Test Confirms It
8:46 Understanding the Starter Tests
11:20 Installing the New Starter
12:05 Final Cranking Test
12:38 Check Engine Light vs. the Customer Complaint
15:11 Getting Roasted by My Son 😂
⚠️ Disclaimer:
ScannerDanner LLC is not responsible for misuse, unauthorized changes, or incorrect application of any information provided. Always follow proper safety protocols when using tools, equipment, or procedures discussed in this video. Use this content at your own risk.
2007 Ford Explorer with an intermittent no-crank that finally became a hard no-crank condition.
Battery voltage was good, and the headlights stayed bright during the crank attempt, so we knew pretty quickly this wasn’t a simple battery problem.
From there, we went straight to the starter circuit and used nothing more than an incandescent test light to check the load side and control side of the starter circuit.
The rusty connections made this one interesting. At first, it looked very possible that we were dealing with a poor connection at the starter terminals. But instead of guessing or replacing parts based on appearance, we kept testing until we could prove exactly where the fault was.
In this video I cover:
• Basic no-crank testing
• Starter load-side and control-side checks
• Why a circuit must be tested under load
• Testing the stud versus the cable eyelet
• Identifying a voltage drop with a test light
• Separating a wiring problem from an internal starter problem
• Why rust alone doesn’t prove a bad connection
• Knowing when scan data is — and isn’t — necessary for a no-crank diagnosis
These are basic starting-system checks that technicians and DIYers can use on almost any vehicle.
The goal isn’t to guess whether the starter is bad. The goal is to prove it.
Want to learn electrical and electronic diagnostics from the ground up?
Join ScannerDanner Premium:
scannerdanner.com/join-scannerdanner-premium.html
14 Days for $1
On ScannerDanner Premium, you'll get:
*In-depth classroom lectures based on the material in my book
*Case studies with real vehicles brought into class
*Troubleshooting using proven diagnostic methods
*Access to our private forum
*Fundamental training in automotive electrical, electronics, and drivability diagnostics
📘 Want to Learn More About Diagnostics?
Check out my field manual, Engine Performance Diagnostics, available as both an eBook and paperback at:
👉 https://linktr.ee/scannerdanner
ScannerDanner Tools:
https://linktr.ee/scannerdanner
0:00 2007 Ford Explorer No-Crank
0:55 Starting Circuit Overview
1:47 Testing Power at the Starter
2:23 Why You Must Test the Circuit Under Load
3:29 Accidentally Making It Crank
4:32 Recreating the No-Crank Condition
5:25 Proving the Fault
7:51 Wiring Problem or Bad Starter?
8:18 The Tap Test Confirms It
8:46 Understanding the Starter Tests
11:20 Installing the New Starter
12:05 Final Cranking Test
12:38 Check Engine Light vs. the Customer Complaint
15:11 Getting Roasted by My Son 😂
⚠️ Disclaimer:
ScannerDanner LLC is not responsible for misuse, unauthorized changes, or incorrect application of any information provided. Always follow proper safety protocols when using tools, equipment, or procedures discussed in this video. Use this content at your own risk.










