Uploaded November 2020 | Updated November 2026, 1 hour ago
In this weeks video we will be building on what we have learned in the past 4 weeks and adding a few tricks and accessories. Let's perform a relative compression(RC) check and include a cylinder sync so we can Identify each cylinder.
The relative compression(RC) check is achieved by cranking the engine over for 5-10 seconds without the engine starting so we need to disable fuel. Some vehicles disable the injectors of you turn the key on, press the pedal to the floor and then hold the accelerator pedal to the floor, keep the pedal down and crank the engine over, if the vehicle has the clear flood feature it will crank without starting. If your vehicle doesn't have this feature then you may need to disable the fuel pump or fuel injectors.
We can either use an amp clamp around the starter cable or use battery voltage to get our RC waveform. If you are using battery voltage it may be helpful to AC couple the waveform to center it on the 0 volt line and also invert the waveform so the peaks represent compression peaks.
Next we need to sync up the waveform with an ignition sync. If the vehicle has plug wires the easiest way is with a secondary ignition pickup, if the vehicle has coil on plug the easiest way is a Coil On Plug wand or paddle but if you don't one of those you can back probe the connector on the ignition control wire. If the the coil is a 2 or 3 wire coil you should use an attenuator with your scope(snapon does not need one). If the coil is a 4 or 5 wire coil you should be fine without an attenuator because the voltage is normally a 0-5 volt square wave.
We also need the firing order for the engine so we know what cylinder is what.
affiliate link used below help support the channel at no addition cost to you. Thank you
2000/200 amp clamp PICO - amzn.to/36k4ucO
secondary ignition pickup - amzn.to/35bxlkm
20:1 attenuator - amzn.to/2JSicwl
back probing set - amzn.to/3587E46
In this weeks video we will be building on what we have learned in the past 4 weeks and adding a few tricks and accessories. Let's perform a relative compression(RC) check and include a cylinder sync so we can Identify each cylinder.
The relative compression(RC) check is achieved by cranking the engine over for 5-10 seconds without the engine starting so we need to disable fuel. Some vehicles disable the injectors of you turn the key on, press the pedal to the floor and then hold the accelerator pedal to the floor, keep the pedal down and crank the engine over, if the vehicle has the clear flood feature it will crank without starting. If your vehicle doesn't have this feature then you may need to disable the fuel pump or fuel injectors.
We can either use an amp clamp around the starter cable or use battery voltage to get our RC waveform. If you are using battery voltage it may be helpful to AC couple the waveform to center it on the 0 volt line and also invert the waveform so the peaks represent compression peaks.
Next we need to sync up the waveform with an ignition sync. If the vehicle has plug wires the easiest way is with a secondary ignition pickup, if the vehicle has coil on plug the easiest way is a Coil On Plug wand or paddle but if you don't one of those you can back probe the connector on the ignition control wire. If the the coil is a 2 or 3 wire coil you should use an attenuator with your scope(snapon does not need one). If the coil is a 4 or 5 wire coil you should be fine without an attenuator because the voltage is normally a 0-5 volt square wave.
We also need the firing order for the engine so we know what cylinder is what.
affiliate link used below help support the channel at no addition cost to you. Thank you
2000/200 amp clamp PICO - amzn.to/36k4ucO
secondary ignition pickup - amzn.to/35bxlkm
20:1 attenuator - amzn.to/2JSicwl
back probing set - amzn.to/3587E46










