As Wood Turns | Twice Turned Bowl - Green To Beauty @AsWoodTurns | Uploaded 2 years ago | Updated 7 hours ago
https://www.AsWoodTurns.com
The elm was harvested almost 2 years ago. Whoever cut it down was not a wood turner because the shape of this block of wood was awful. It was trapezoidal with some of the heart side corners cut off. I could have reversed it but chose not to.
When rough turning, I left the wall about 1 inch thick since I did not know how much this wood would warp while drying.
After rough turning, I coated it with a PVA based sealer, Tree Saver, available from Craft Supplies, USA. Periodically, I weighed and recorded the weight each time. This is the most reliable way for me to know when a bowl is dry and stable.
I remounted the bowl against a wood faceplate held in place with the live center in the original divot from the live center. The enabled the mounting tenon to be again turned round and with a flat top. As a bonus, I could also trim back some of the exterior wood.
After reversing the bowl into a chuck, I could finish turning the bowl except for the tenon area.
While I have a set of Cole jaws, I chose to again press the bowl against a wood faceplate while finishing the foot area. My intent was to then sand the remaining area for the nub left by the live center. However, I pushed it one cut too far; the nub broke away before I was finished. So back to the Cole jaws to sand the foot.
Walnut oil brings out the color and grain.
Enjoy!
Blog: https://www.AsWoodTurns.com
FB: https://www.Facebook.com/AsWoodTurns
InstaGram: http://www.Instgram.com/as_wood_turns
Etsy: etsy.com/shop/AsWoodTurnsTools
Pinterest pinterest.com/aswoodturns
#greenWood #WetWood #Bowl #twiceTurned #bowlTurning #woodworking #woodturning #woodturningprojects #lathe #AlanStratton #video #DIY
https://www.AsWoodTurns.com
The elm was harvested almost 2 years ago. Whoever cut it down was not a wood turner because the shape of this block of wood was awful. It was trapezoidal with some of the heart side corners cut off. I could have reversed it but chose not to.
When rough turning, I left the wall about 1 inch thick since I did not know how much this wood would warp while drying.
After rough turning, I coated it with a PVA based sealer, Tree Saver, available from Craft Supplies, USA. Periodically, I weighed and recorded the weight each time. This is the most reliable way for me to know when a bowl is dry and stable.
I remounted the bowl against a wood faceplate held in place with the live center in the original divot from the live center. The enabled the mounting tenon to be again turned round and with a flat top. As a bonus, I could also trim back some of the exterior wood.
After reversing the bowl into a chuck, I could finish turning the bowl except for the tenon area.
While I have a set of Cole jaws, I chose to again press the bowl against a wood faceplate while finishing the foot area. My intent was to then sand the remaining area for the nub left by the live center. However, I pushed it one cut too far; the nub broke away before I was finished. So back to the Cole jaws to sand the foot.
Walnut oil brings out the color and grain.
Enjoy!
Blog: https://www.AsWoodTurns.com
FB: https://www.Facebook.com/AsWoodTurns
InstaGram: http://www.Instgram.com/as_wood_turns
Etsy: etsy.com/shop/AsWoodTurnsTools
Pinterest pinterest.com/aswoodturns
#greenWood #WetWood #Bowl #twiceTurned #bowlTurning #woodworking #woodturning #woodturningprojects #lathe #AlanStratton #video #DIY