Uploaded May 2020 | Updated November 2026, 8 minutes ago
Originally live-streamed to Twitch here:
twitch.tv/tincansynthjam
My podcast is called Tin Can Synth Jam, subscribe to it!
The software I use is called OBS, get it, it's amazing. Even my super crappy laptop camera and a USB webcam I found under a pile of dirty laundry manage to make this video much cooler than it should be.
----Show notes from the podcast-----
I'm excited about this episode, since it's the first one I recorded on video as well as audio. I used my crap laptop camera and a USB webcam layered together, holding the webcam in one of my hands, manipulating the synth's triggers switches buttons and knobs with the other hand (or sometimes with the webcam hand). So if you want to watch knobs turn and HEAR THE RESULT (this is a thing that I really like) head over to Youtube to watch the video!
Here's the link: (it's this video)
I'm learning which modules I really enjoy. One of my favorites is a hyper simple gated "beep" module, made from a CD4046 PLL chip that just does a square wave at some frequency, and there's a 555 timer tripping the "enable" pin, letting the tone out. I built it to emulate the toy keyboard percussion sounds, and it's an incredibly rewarding module to play live. So much more versatile than I thought it would be.
A second module I'm loving right now is my "Frenetic Robot Noise" module. It's complicated, unlike the "beep" module. It's got a white noise generator. It's got a "shimmer" noise generator, made from a hex Schmitt trigger chip (CD40106). It's got two CD4046 oscillators that both get "sample-and-hold"ed by another VCO with base frequency and frequency range set with four thumb wheel potentiometers. So basically, the CD4046 makes a tone set by a sample-and-hold voltage from a different oscillator. Then some fraction of a second later, it gets a new voltage that sets a new frequency. The three noise sources are mixed, and sent through a very difficult to control low-pass filter that uses LDR/LED Vactrol type device for the cutoff.
And then of course, reverb. Lots and lots of reverb.
Originally live-streamed to Twitch here:
twitch.tv/tincansynthjam
My podcast is called Tin Can Synth Jam, subscribe to it!
The software I use is called OBS, get it, it's amazing. Even my super crappy laptop camera and a USB webcam I found under a pile of dirty laundry manage to make this video much cooler than it should be.
----Show notes from the podcast-----
I'm excited about this episode, since it's the first one I recorded on video as well as audio. I used my crap laptop camera and a USB webcam layered together, holding the webcam in one of my hands, manipulating the synth's triggers switches buttons and knobs with the other hand (or sometimes with the webcam hand). So if you want to watch knobs turn and HEAR THE RESULT (this is a thing that I really like) head over to Youtube to watch the video!
Here's the link: (it's this video)
I'm learning which modules I really enjoy. One of my favorites is a hyper simple gated "beep" module, made from a CD4046 PLL chip that just does a square wave at some frequency, and there's a 555 timer tripping the "enable" pin, letting the tone out. I built it to emulate the toy keyboard percussion sounds, and it's an incredibly rewarding module to play live. So much more versatile than I thought it would be.
A second module I'm loving right now is my "Frenetic Robot Noise" module. It's complicated, unlike the "beep" module. It's got a white noise generator. It's got a "shimmer" noise generator, made from a hex Schmitt trigger chip (CD40106). It's got two CD4046 oscillators that both get "sample-and-hold"ed by another VCO with base frequency and frequency range set with four thumb wheel potentiometers. So basically, the CD4046 makes a tone set by a sample-and-hold voltage from a different oscillator. Then some fraction of a second later, it gets a new voltage that sets a new frequency. The three noise sources are mixed, and sent through a very difficult to control low-pass filter that uses LDR/LED Vactrol type device for the cutoff.
And then of course, reverb. Lots and lots of reverb.










