Uploaded November 2026 | Updated November 2026, 3 hours ago
PLC timer program, steps one and two: define what the motor has to do, then the IO. The stop button is wired normally closed, so it is on when nobody presses it.
โก QUICK ANSWER
Before a timer goes near a rung, the task gets written down. Press start and the motor waits 2 seconds. Press stop and it runs on for 5 seconds. Total the running time across every stop, and at the service interval stop the motor and block restarts until maintenance presses a reset. Then the IO. X1 is the start button, normally open. X2 is the stop button, wired normally closed, so it reads on while nobody is touching it and a cut wire or a failed contact stops the machine instead of leaving it running. That inversion is the most important wiring decision in the program, and it is made before any timer is chosen.
๐ FULL STEP-BY-STEP + DOWNLOADS (project file, example program, Structured Text)
accautomation.ca/plc-timers-explained-ton-tof-rto
๐ WHAT YOU'LL LEARN
โ Write a task definition that states the delay, the run on time and the service interval before choosing any instruction
โ Wire a stop button normally closed so a broken wire stops the machine rather than leaving it running
โ Assign X1 and X2 to the start and stop buttons on the Control Panel scene and know which one reads on at rest
โ Shorten a service interval to 20 seconds while testing so you can watch the behaviour instead of waiting for it
โ FREQUENTLY ASKED
Q: Why is a stop button wired normally closed?
A: So the input is on while the button is at rest. If the wire breaks or the contact fails, the input goes off and the machine stops, which is the safe direction to fail in.
Q: Do I really need to define the task before programming?
A: It is the step that decides which timer you need. A start delay is a TON, a run on after stop is a TOF, and a running total across stops is an RTO. Write the behaviour down and the instruction choice makes itself.
๐ Full walkthrough, example file and Structured Text version: accautomation.ca/plc-timers-explained-ton-tof-rto
๐ MORE RESOURCES
โถ Full video โ TON, TOF or RTO: Which PLC Timer Should You Use? youtu.be/TL4jVWr_xL4
โถ Free ACC PLC Simulator, runs in your browser: accautomation.ca/simulator
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCTimer #PLCTutorial #LearnPLC #Shorts
Regards,
Garry
ACC Automation
accautomation.ca
PLC timer program, steps one and two: define what the motor has to do, then the IO. The stop button is wired normally closed, so it is on when nobody presses it.
โก QUICK ANSWER
Before a timer goes near a rung, the task gets written down. Press start and the motor waits 2 seconds. Press stop and it runs on for 5 seconds. Total the running time across every stop, and at the service interval stop the motor and block restarts until maintenance presses a reset. Then the IO. X1 is the start button, normally open. X2 is the stop button, wired normally closed, so it reads on while nobody is touching it and a cut wire or a failed contact stops the machine instead of leaving it running. That inversion is the most important wiring decision in the program, and it is made before any timer is chosen.
๐ FULL STEP-BY-STEP + DOWNLOADS (project file, example program, Structured Text)
accautomation.ca/plc-timers-explained-ton-tof-rto
๐ WHAT YOU'LL LEARN
โ Write a task definition that states the delay, the run on time and the service interval before choosing any instruction
โ Wire a stop button normally closed so a broken wire stops the machine rather than leaving it running
โ Assign X1 and X2 to the start and stop buttons on the Control Panel scene and know which one reads on at rest
โ Shorten a service interval to 20 seconds while testing so you can watch the behaviour instead of waiting for it
โ FREQUENTLY ASKED
Q: Why is a stop button wired normally closed?
A: So the input is on while the button is at rest. If the wire breaks or the contact fails, the input goes off and the machine stops, which is the safe direction to fail in.
Q: Do I really need to define the task before programming?
A: It is the step that decides which timer you need. A start delay is a TON, a run on after stop is a TOF, and a running total across stops is an RTO. Write the behaviour down and the instruction choice makes itself.
๐ Full walkthrough, example file and Structured Text version: accautomation.ca/plc-timers-explained-ton-tof-rto
๐ MORE RESOURCES
โถ Full video โ TON, TOF or RTO: Which PLC Timer Should You Use? youtu.be/TL4jVWr_xL4
โถ Free ACC PLC Simulator, runs in your browser: accautomation.ca/simulator
โถ PLC Beginners Guide: accautomation.ca/programming/plc-beginners-guide
๐ฌ Questions? Drop a comment below.
๐ New tutorials every Monday โ Subscribe and hit the bell!
#PLC #LadderLogic #IndustrialAutomation #PLCProgramming #ACCAutomation #PLCTimer #PLCTutorial #LearnPLC #Shorts
Regards,
Garry
ACC Automation
accautomation.ca










