Uploaded February 2025 | Updated September 2026, 6 hours ago
To get a Bambu code performance baseline, tonight I test a fully stock gcode using system presets and setup some brand new material that was fully dried to get a good baseline for what SteinWipe Gcode needs to surpass.
After 2 months of programming SteinWipe Motion Control and hundreds of people are now using the project - I my self have not printed anything other than primitives to test the system. How bout that? So last night I printed a 4 color Marlin model and the result was a perfect model with 52% less purge over the stock Bambu presets! This test will now compare apples to apples; everything is stock for tonights print.
This project continues to evolve based on feedback and support from the community. You may get your hands on SWMC and support everything SteinWipe plus gain exclusive updates and direct support here (Discord link included):
bit.ly/SupportSteinWipe
MakerWorld Project Model - Give it a boost if this listing helped you out :)
makerworld.com/en/models/1025501?from=search#profileId-1050795
SteinWipe Project Log
bit.ly/LeckiesteinProjectLog
Check out documentation for this project
bit.ly/SteinWipeDocumentation
Support creating more projects like this one:
patreon.com/leckiestein
Highlights:
Waiting for viewers | 0:00 |
Introduction | 0:04:10 |
Filament Drying / Install | 0:04:50 |
How to calibrate all filaments at once | 0:13:39 |
The first sign of things to come | 29:28 |
Setting up the model | 38:33 |
System preset settings overview | 41:40 |
Talk about efficient nozzle flushing | 44:10 |
Talk about how Long Retractions When Cut Works (firmware retraction) | 48:31 |
Looking at the slicer stats | 54:44 |
Talk about Flow Dynamics and Bed Leveling check boxes | 57:25 |
Print starts and looking first routine | 59:50 |
Printing while I sleep | 1:25:00 |
Where things start to go wrong | 4:57:30 |
Chaos begins | 5:24:40 |
Please make it stop! | 5:27:05 |
Something miraculous happens | 5:27:27 |
✌YEET! | 6:01:38 |
Woke up to a bunch of messages and Handy canceled the print | 6:58:20 |
Assessing the damage | 9:25:30 |
Found the problem | 9:32:38 |
New feature in SteinWipe - how chute tapping works | 9:35:30 |
How to retighten the belts | 9:44:25 |
How to run a calibration | 9:56:00 |
Chute tapping cont. | 10:21:35 |
To get a Bambu code performance baseline, tonight I test a fully stock gcode using system presets and setup some brand new material that was fully dried to get a good baseline for what SteinWipe Gcode needs to surpass.
After 2 months of programming SteinWipe Motion Control and hundreds of people are now using the project - I my self have not printed anything other than primitives to test the system. How bout that? So last night I printed a 4 color Marlin model and the result was a perfect model with 52% less purge over the stock Bambu presets! This test will now compare apples to apples; everything is stock for tonights print.
This project continues to evolve based on feedback and support from the community. You may get your hands on SWMC and support everything SteinWipe plus gain exclusive updates and direct support here (Discord link included):
bit.ly/SupportSteinWipe
MakerWorld Project Model - Give it a boost if this listing helped you out :)
makerworld.com/en/models/1025501?from=search#profileId-1050795
SteinWipe Project Log
bit.ly/LeckiesteinProjectLog
Check out documentation for this project
bit.ly/SteinWipeDocumentation
Support creating more projects like this one:
patreon.com/leckiestein
Highlights:
Waiting for viewers | 0:00 |
Introduction | 0:04:10 |
Filament Drying / Install | 0:04:50 |
How to calibrate all filaments at once | 0:13:39 |
The first sign of things to come | 29:28 |
Setting up the model | 38:33 |
System preset settings overview | 41:40 |
Talk about efficient nozzle flushing | 44:10 |
Talk about how Long Retractions When Cut Works (firmware retraction) | 48:31 |
Looking at the slicer stats | 54:44 |
Talk about Flow Dynamics and Bed Leveling check boxes | 57:25 |
Print starts and looking first routine | 59:50 |
Printing while I sleep | 1:25:00 |
Where things start to go wrong | 4:57:30 |
Chaos begins | 5:24:40 |
Please make it stop! | 5:27:05 |
Something miraculous happens | 5:27:27 |
✌YEET! | 6:01:38 |
Woke up to a bunch of messages and Handy canceled the print | 6:58:20 |
Assessing the damage | 9:25:30 |
Found the problem | 9:32:38 |
New feature in SteinWipe - how chute tapping works | 9:35:30 |
How to retighten the belts | 9:44:25 |
How to run a calibration | 9:56:00 |
Chute tapping cont. | 10:21:35 |
