Uploaded February 2019 | Updated November 2026, 1 hour ago
I have been waiting a long time to take the plunge into resin casting. Well, I finally did it. It did not go without hiccups though. I could not get a good seal with the teflon tape so I resorted to using some Loctite to seal the thread of the pipe fittings. The lid's gasket is still leaking a little bit, but I was still able to get a clear cast free of bubbles (it appears that was through the dark blue). All in all, I resounding success. Below are all of the parts that I used to convert the pressure tank over to a pressure pot. I will making a pen out of the blanks really soon! Stay tuned for that video and please subscribe so you don't miss it!
Please leave a comment if there are any questions you have or if you feel like I missed explaining a step.
My website:
wolfridgewoodworking.com
SUBSCRIBE: youtube.com/channel/UCUVMh5tubVADcaNujTMVdGA
Bob (RJBWoodTurner)'s Pressure Pot video
bit.ly/2sWZcAZ
PARTS USED (NOT affiliate links):
Harbor Freight Pressure Tank
bit.ly/2SwoxzT
Scale to weigh resin
amzn.to/2Sv1hT7
Alumilite Clear
bit.ly/2Bm1ZID
Alumilite 15 Color Dye Set
bit.ly/2AZOm1O
24"x12"x1/2" HDPE Sheet
amzn.to/2RFH5te
90 Degree Brass Elbow, 1/4" Male Pipe x 1/4" Female Pipe
amzn.to/2MTuv8T
Brass Mini Ball Valve, 1/4" NPT Female
amzn.to/2HYnbtP
Brass Pipe Fitting Cap, 1/4" NPT Female
amzn.to/2Doa7IT
3/8" x 1/4" Brass Reduce Plug
amzn.to/2t7uGV1
Quick Disconnect Airline Coupler, 1/4" NPT Male
amzn.to/2Dep3sK
Loctite
thd.co/2DbOHyq
TOOLS USED (NOT affiliate links):
RIDGID R4512 10 in. 13-Amp Cast Iron Table Saw
amzn.to/2GFNWCO
CAMERA GEAR:
Canon M50 Mirrorless Camera
amzn.to/2ORcEQ5
Sigma 17-50mm f/2.8 Lens:
amzn.to/2QcB7Qj
I have been waiting a long time to take the plunge into resin casting. Well, I finally did it. It did not go without hiccups though. I could not get a good seal with the teflon tape so I resorted to using some Loctite to seal the thread of the pipe fittings. The lid's gasket is still leaking a little bit, but I was still able to get a clear cast free of bubbles (it appears that was through the dark blue). All in all, I resounding success. Below are all of the parts that I used to convert the pressure tank over to a pressure pot. I will making a pen out of the blanks really soon! Stay tuned for that video and please subscribe so you don't miss it!
Please leave a comment if there are any questions you have or if you feel like I missed explaining a step.
My website:
wolfridgewoodworking.com
SUBSCRIBE: youtube.com/channel/UCUVMh5tubVADcaNujTMVdGA
Bob (RJBWoodTurner)'s Pressure Pot video
bit.ly/2sWZcAZ
PARTS USED (NOT affiliate links):
Harbor Freight Pressure Tank
bit.ly/2SwoxzT
Scale to weigh resin
amzn.to/2Sv1hT7
Alumilite Clear
bit.ly/2Bm1ZID
Alumilite 15 Color Dye Set
bit.ly/2AZOm1O
24"x12"x1/2" HDPE Sheet
amzn.to/2RFH5te
90 Degree Brass Elbow, 1/4" Male Pipe x 1/4" Female Pipe
amzn.to/2MTuv8T
Brass Mini Ball Valve, 1/4" NPT Female
amzn.to/2HYnbtP
Brass Pipe Fitting Cap, 1/4" NPT Female
amzn.to/2Doa7IT
3/8" x 1/4" Brass Reduce Plug
amzn.to/2t7uGV1
Quick Disconnect Airline Coupler, 1/4" NPT Male
amzn.to/2Dep3sK
Loctite
thd.co/2DbOHyq
TOOLS USED (NOT affiliate links):
RIDGID R4512 10 in. 13-Amp Cast Iron Table Saw
amzn.to/2GFNWCO
CAMERA GEAR:
Canon M50 Mirrorless Camera
amzn.to/2ORcEQ5
Sigma 17-50mm f/2.8 Lens:
amzn.to/2QcB7Qj










