Woodturning: The Flying Scrap Lidded Box @WolfRidgeWoodworking
Woodturning: The Flying Scrap Lidded Box  @WolfRidgeWoodworking
Uploaded September 2019 | Updated November 2026, 2 days ago
Today's project is a bit of an over achiever. It took flight not once, but twice! Ha Ha. Seriously though, my pen blank scrap bin was starting to overflow. So I thought they would make the perfect lidded box along with some clear resin from TotalBoat.

I took some random scraps from my pen blank bin. I mostly used acrylic pen blanks because I seemed to have more of those than the wooden ones. Plus, the acrylic ones are way more colorful. I used most of the wooden ones to fill up the middle portion that would be turned away. The TotalBoat resin system makes it very easy to measure out the correct resin and hardener. After taking it out of the pressure pot, I used some 5 minute epoxy to attach a glue block.

I used the Easy Wood Tools Mid Size square carbide with a negative rake cutter. Those cutters are amazing and leave zero chip out, but man is it tough cutting through wood with them. It made quick work in truing up the outside, but there wasn't much too shaping since I was fine with the shape of the container. Next came hollowing out the inside. I got a good head start with a 2" forstner bit, but it would prove quite challenging getting past that 2 inches. I thought it would be a good idea to use the standard square carbide to thin the walls a bit. Well that proved to be a big mistake. As you can see from the video, I was taking very small cuts, but it had a catch and boom....it came flying off the lathe at 1,500 RPM. To say that it shocked me would be an understatement! I tried a little more to thin the walls down, but the tools just bounced and didn't really cut. So, the walls and bottom are thicker than I would like, but I have since ordered a 2 3/4" forstner bit and that should allow me to get the walls to the thickness that I feel is better. I finished the box by sanding the inside and out from 80 to 600 grit. Since there was so much acrylic, I wanted to try the micro mesh which goes from 1,000 to 12,000 grit. It left the same finish as on the pine cone lidded box where I did not use them. I applied Mylands Sanding Sealer, Ack's Abrasive and Polishing Pastes, and finally Myland's Friction Polish. I really feel like the Myland's Friction Polish does a great job at covering up the fine scratches on resin projects. I used a 1/8" parting tool to remove the finished box from the glue block. I didn't realize how far I cut in and it came flying off the lathe for a second time.

Next came the lid. The first step was to attach a piece of walnut to a glue block with some 5 minute epoxy. I was able to quickly turn the blank round using a 1" roughing gouge. I formed the lid using the 1/2" & 3/8" bowl gouges, square scraper, and Easy Wood Tools Detailer. To finish things off, I finished the lid using the same process as the box itself.

I hope you enjoy this video. Please let me know if there is a project you'd like to see me make and I will do my best to do it. Thank you for all the support you have shown me and the channel!

Ack's Abrasive & Polishing Paste
ackswoodpaste.com
Use WOLF10 at checkout to get 10% off your order

Materials used on the Flying Scrap Lidded Box (affiliate):
TotalBoat High Performance Epoxy (2:1) w/ Slow Hardener: amzn.to/30c1ZJE
Mylands Cellulose Sanding Sealer: amzn.to/2V6bC5k
Acks Abrasive Sanding Paste & Polish: ackswoodpaste.com
Mylands High Build Friction Polish: amzn.to/2Km70Wl
Abranet Sanding Screen: bit.ly/2lD2yJ3

Tools used on the Flying Scrap Lidded Box (affiliate):
Jet 1221VS Lathe: amzn.to/2OdLhCB
Nova 48202 G3 Wood Turning Chuck: amzn.to/2yGRoGC
3/8" Bowl Gouge: amzn.to/30Zla5o
1/2" Bowl Gouge: amzn.to/34HDXon
1" Standard Skew Chisel: amzn.to/2XoYbz0
1/8" HSS Parting Tool: bit.ly/2GAEBey
Easy Wood Tools Carbide Tools: amzn.to/2N0FTy5
Easy Wood Tools Ci3 Round Negative Rake Carbide Cutter: amzn.to/31uvjaa

SUBSCRIBE: youtube.com/wolfridgewoodworking

Please leave a comment if there are any questions you have.

You can also find me here:
website: wolfridgewoodworking.com
Facebook: facebook.com/wolfridgewoodworking
Instagram: instagram.com/wolfridgewoodworking
Email: edlparker3@gmail.com

Ed Parker
P.O Box 1893
Queen Creek, AZ 85142

Music by Epidemic Sound (http://www.epidemicsound.com)
Woodturning: The Flying Scrap Lidded BoxCreality Falcon2:  22 Watts of Power and 10 Minutes From Unboxing to Cutting!Woodturning: Natural Edge Cherry Bowl & GiveawayWoodworking: The Record Stand that Reacts to Album Covers!Woodturning: Maple, Padauk, & Wenge LighthouseWoodturning: Tiny Spalted Red Alder Lidded BoxWoodturning: Pull Tabs, Resin & Aspen BowlHow to Make an Awesome Halloween Project with the Xtool D1!Woodturning: Big Ben Pen & African RosewoodWoodturning: Mystery Resin & Burl ExperimentWoodturning: 49ers Football PenWoodturning: A Basket Illusion Vase
Wolf Ridge Woodworking |

Woodturning: The Flying Scrap Lidded Box

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER