Winston Moy | Shapeoko 3: My First Cuts & Project @WinstonMakes | Uploaded 9 years ago | Updated 3 minutes ago
An introduction to the Shapeoko 3 (2015), the state of software support, and my first project utilizing the S3's larger work area (a DIY vacuum table).
Note: The information given in this video is an extrapolation from my cursory research on the subject. It may not be 100% accurate, nor current.
Get Carbide Motion here: http://carbide3d.com/downloads
Get Universal Gcode Sender here: github.com/winder/Universal-G-Code-Sender
My threaded inserts: http://amzn.to/1bbeWi9
NOTE: DO NOT use the 9mm hole diameter indicated on the packaging. I've found 8mm (5/16") to be a much better fit. Keep this in mind if you're programming your own holes, or drilling them by hand.
-----
Outro: "Extreme Sport" by K-319
An introduction to the Shapeoko 3 (2015), the state of software support, and my first project utilizing the S3's larger work area (a DIY vacuum table).
Note: The information given in this video is an extrapolation from my cursory research on the subject. It may not be 100% accurate, nor current.
Get Carbide Motion here: http://carbide3d.com/downloads
Get Universal Gcode Sender here: github.com/winder/Universal-G-Code-Sender
My threaded inserts: http://amzn.to/1bbeWi9
NOTE: DO NOT use the 9mm hole diameter indicated on the packaging. I've found 8mm (5/16") to be a much better fit. Keep this in mind if you're programming your own holes, or drilling them by hand.
-----
Outro: "Extreme Sport" by K-319
![Intro to 5-Axis Machining on the PocketNC v2 - Project #112 [CNC]](https://i.ytimg.com/vi/kdJA0g0E6uQ/hqdefault.jpg "Intro to 5-Axis Machining on the PocketNC v2 - Project #112 [CNC]
After a PocketNC showed up on my doorstep, learning 5-axis machining became my top priority. This is the story of how I went from a 5-axis know-nothing, to a 5-axis amateur.
Let this be a lesson to you all: ALWAYS participate in the Fusion Cam Challenges ;)
To learn more about the PocketNC v2, check out their website: http://www.pocketnc.com/pocket-nc-v2/pocket-nc-v2
Help support content like this: https://www.patreon.com/winstonmoy
Can’t get enough of me? Check out my second channel: https://www.youtube.com/c/WinstonMakesMore
Stalk me on Social Media: @WinstonMakes (insta/twitter)")
![USB-Powered Oak & Acrylic LED Lamp - Project #117 [CNC]](https://i.ytimg.com/vi/lMkf33wdv3Q/hqdefault.jpg "USB-Powered Oak & Acrylic LED Lamp - Project #117 [CNC]
Up-cycling some old acrylic sheeting into an LED lamp by layering it with oak. If I were to do this again, Id frost up the inside surface more to increase diffusion of the LEDs.
LED strip used: https://amzn.to/2DSKLkc
Compression endmill: http://www.harveytool.com/prod/End-Mills-for-Composites/Material-Specific-End-Mills/Browse-Our-Products_248/End-Mills-for-Composites Compression-Cutter_187.aspx
Single Flute Upcut for Plastic: http://www.harveytool.com/prod/End-Mills-for-Plastics/Material-Specific-End-Mills/Browse-Our-Products_253/End-Mills-for-Plastics Square-Upcut Single-Flute_113.aspx_Q_keywords_E_52508
Help support content like this: https://www.patreon.com/winstonmoy
Can’t get enough of me? Check out my second channel: https://www.youtube.com/c/WinstonMakesMore
Stalk me on Social Media: @WinstonMakes (insta/twitter)
*Note: I am a member of the Amazon Affiliate program. By using my links, you are helping to support my content.")
