Mr.D - Falling with style | Setting up iNav 4 - A complete, new set up and installation for fixed wings @MrD | Uploaded 2 years ago | Updated 3 minutes ago
🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC
In this long video (thank the flying gods for chapters!), we look at how to set up iNav 4, for fixed wing, from scratch. This is taken from the perspective of a new plane, or just starting from a full chip erase. I cover the basics, plus a bit more.
This guide will get all versions of iNav 4 (4.0 "Red Kite", 4.1 "Raging Sparrow" etc) where you need them to be. Because of the new way the version numbers are changed; there will be no features that break anything on the same major version number.
I have some more detailed videos on specific parts of the set up process. In this video I mention when they would be useful. So feel free to pause this video, and check out the more detailed video. The video links are below the contents section. There is also an article for the set up process at mrd-rc.com/tutorials-tools-and-testing/flight-controller-therapy/a-complete-guide-to-setting-up-inav-4 I would recommend having the article open as you set up iNav.
In the video, I mention some CLI to switch to the default OSD on failsafe. That CLI command is: set osd_failsafe_switch_layout = ON
✈️ Contents ✈️
0:00:00 Introduction
0:03:18 Getting iNav Configurator
0:07:24 Launching iNav Configurator
0:08:28 Checking the flight controller is ok and getting the target
0:11:56 Flashing the flight controller
0:15:20 Resolving problems getting in to DFU mode
0:18:18 Choosing your defaults
0:19:29 Calibrating the accelerometer
0:22:02 Setting up the mixer
0:25:14 Notes to make when you install the flight controller in your airplane
0:26:08 What's in the demo plane?
0:28:06 Checking the board alignment
0:30:16 Setting initial angle of attack and how to use auto level
0:31:26 Setting up the ports
0:31:43 Telemetry not working on Crossfire on an F4 flight controller?
0:33:18 MSP; which ports do you need it on?
0:35:26 Setting up the receiver
0:37:32 What the channel bars should look like on the receiver page
0:40:04 Setting up and testing the GPS
0:45:06 Adding the modes
0:48:47 Configuring the outputs
0:52:05 Testing the motors
0:53:19 Checking the servo direction and stabilisation
0:59:56 Setting up and testing failsafe
1:02:11 Setting up return to home
1:06:55 A quick overview of autolaunch and the fixed wing navigation settings
1:09:37 Setting up your OSD and how to quickly copy layouts
1:18:16 Checking the video and SmartAudio
1:19:52 Calibrating the current sensor
1:23:53 Conclusion
✈️ Detail videos ✈️
🛩 Combining switches in OpenTX:
🛩 Understanding iNav's Mixer: youtu.be/ysyJoDEeUjA
🛩 Board alignment: youtu.be/vT3IwRkjpHg
🛩 What is a UART?: youtu.be/vWvcBSN3jqM
🛩 Setting up your transmitter for iNav: youtu.be/b1m1aSrtVCQ
🛩 iNav Modes: youtu.be/LuSghRxc-as
🛩 iNav in-flight tuning: youtu.be/A5i0gs9LfE8
🛩 Return to Home: youtu.be/J9mv7gNRD9U
🛩 Setting up Autolaunch: youtu.be/yfdYMKgbb6M
🛩 Tuning series, with Marc Hoffmann: youtube.com/playlist?list=PLtuty5zAsZ_bAx2pL9x3FjDdGEbRUGJMZ
🛩 Current sensor calibration: youtu.be/inmYVBpaWPw
🛩 Setting up control surfaces: youtu.be/tGRDZzaerOE
Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer.
✈️ In this video ✈️
🔗 INAV Fixed Wing Group OpenTX models:
🔗 OSD Switcher Tool: mrd-rc.com/tutorials-tools-and-testing/useful-tools/inav-osd-switcher-tool
🔗 iNav Configurator: github.com/iNavFlight/inav-configurator
🔗 iNav Release Notes: (4.0) github.com/iNavFlight/inav/wiki/4.0.0-Release-notes (4.1) github.com/iNavFlight/inav/wiki/4.1.0-Release-notes
🔗 ImpulseRC Driver Fixer: impulserc.com/pages/downloads
✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.
✈️ Supporting me and other resources ✈️
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su
🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.
Thank you for your time, and don't forget to fly it like you stole it!
🔗 https://www.MrD-RC.com 🔗 patreon.com/MrD_RC
In this long video (thank the flying gods for chapters!), we look at how to set up iNav 4, for fixed wing, from scratch. This is taken from the perspective of a new plane, or just starting from a full chip erase. I cover the basics, plus a bit more.
This guide will get all versions of iNav 4 (4.0 "Red Kite", 4.1 "Raging Sparrow" etc) where you need them to be. Because of the new way the version numbers are changed; there will be no features that break anything on the same major version number.
I have some more detailed videos on specific parts of the set up process. In this video I mention when they would be useful. So feel free to pause this video, and check out the more detailed video. The video links are below the contents section. There is also an article for the set up process at mrd-rc.com/tutorials-tools-and-testing/flight-controller-therapy/a-complete-guide-to-setting-up-inav-4 I would recommend having the article open as you set up iNav.
In the video, I mention some CLI to switch to the default OSD on failsafe. That CLI command is: set osd_failsafe_switch_layout = ON
✈️ Contents ✈️
0:00:00 Introduction
0:03:18 Getting iNav Configurator
0:07:24 Launching iNav Configurator
0:08:28 Checking the flight controller is ok and getting the target
0:11:56 Flashing the flight controller
0:15:20 Resolving problems getting in to DFU mode
0:18:18 Choosing your defaults
0:19:29 Calibrating the accelerometer
0:22:02 Setting up the mixer
0:25:14 Notes to make when you install the flight controller in your airplane
0:26:08 What's in the demo plane?
0:28:06 Checking the board alignment
0:30:16 Setting initial angle of attack and how to use auto level
0:31:26 Setting up the ports
0:31:43 Telemetry not working on Crossfire on an F4 flight controller?
0:33:18 MSP; which ports do you need it on?
0:35:26 Setting up the receiver
0:37:32 What the channel bars should look like on the receiver page
0:40:04 Setting up and testing the GPS
0:45:06 Adding the modes
0:48:47 Configuring the outputs
0:52:05 Testing the motors
0:53:19 Checking the servo direction and stabilisation
0:59:56 Setting up and testing failsafe
1:02:11 Setting up return to home
1:06:55 A quick overview of autolaunch and the fixed wing navigation settings
1:09:37 Setting up your OSD and how to quickly copy layouts
1:18:16 Checking the video and SmartAudio
1:19:52 Calibrating the current sensor
1:23:53 Conclusion
✈️ Detail videos ✈️
🛩 Combining switches in OpenTX:
🛩 Understanding iNav's Mixer: youtu.be/ysyJoDEeUjA
🛩 Board alignment: youtu.be/vT3IwRkjpHg
🛩 What is a UART?: youtu.be/vWvcBSN3jqM
🛩 Setting up your transmitter for iNav: youtu.be/b1m1aSrtVCQ
🛩 iNav Modes: youtu.be/LuSghRxc-as
🛩 iNav in-flight tuning: youtu.be/A5i0gs9LfE8
🛩 Return to Home: youtu.be/J9mv7gNRD9U
🛩 Setting up Autolaunch: youtu.be/yfdYMKgbb6M
🛩 Tuning series, with Marc Hoffmann: youtube.com/playlist?list=PLtuty5zAsZ_bAx2pL9x3FjDdGEbRUGJMZ
🛩 Current sensor calibration: youtu.be/inmYVBpaWPw
🛩 Setting up control surfaces: youtu.be/tGRDZzaerOE
Thank you for watching this video. Time is precious, so I hope that you got some benefit from this video. If you have any questions, please leave a comment and I'll do my best to answer.
✈️ In this video ✈️
🔗 INAV Fixed Wing Group OpenTX models:
🔗 OSD Switcher Tool: mrd-rc.com/tutorials-tools-and-testing/useful-tools/inav-osd-switcher-tool
🔗 iNav Configurator: github.com/iNavFlight/inav-configurator
🔗 iNav Release Notes: (4.0) github.com/iNavFlight/inav/wiki/4.0.0-Release-notes (4.1) github.com/iNavFlight/inav/wiki/4.1.0-Release-notes
🔗 ImpulseRC Driver Fixer: impulserc.com/pages/downloads
✈️ Help other RC pilots find this video ✈️
If you found the video useful, I'd appreciate a thumbs up. This will help YouTube share this video with other RC pilots who may find it helpful. If you would like to get more videos when they become available, please subscribe and click the notifications bell icon. If there are links above, they may be affiliate links. If you click them, it will help me and my channel at no additional cost to you.
✈️ Supporting me and other resources ✈️
🛩 You can also join like-minded people at the Fixed Wing RC Rebels group and INAV Fixed Wing Group on Facebook.
🛩 Join the channel's discord server at discord.gg/HMvrgZX6su
🛩 Liking the video, subscribing, and clicking the bell icon can help greatly. This shows YouTube that the video is helpful, so it will be shown to more people, who may have the problem dealt with here.
🛩 If you prefer, you could always buy me a Coffee at mrd-rc.com/go/ko-fi
🛩 I also have merch at mrd-rc.creator-spring.com This include branded items as well as general fixed wing RC apparel.
Thank you for your time, and don't forget to fly it like you stole it!
