Uploaded May 2018 | Updated November 2026, 3 hours ago
This video from Sears PartsDirect shows how to replace an oven door switch in a range. The oven door switch shuts off the light when you close the door (unless you’ve set the light to stay on). It also verifies that the oven door is shut during the self-clean cycle. If the oven light stays on when you close the door or the self-clean cycle either won’t start or stops in the middle, replace the door switch with a manufacturer-approved part.
Visit us at:
https://www.searspartsdirect.com?sid=soc:youtube:replacing-a-range-oven-door-switch
Or call 1-800-437-1673 to speak with a parts specialist.
The video includes these parts and tools. Look up your model to make sure you get the right parts for your range.
Oven door switch
searspartsdirect.com/part-number/316445500/0022/628.html?sid=soc:youtube:card-direct-part-link
Find parts for your Range at:
searspartsdirect.com/partsdirect/product-types/Range-Parts?sid=soc:youtube:rangeparts
Or, click here to schedule an appointment with a repair technician.
searshomeservices.com/repair#showall
Transcript:
The first step is to unplug the range or shut off the circuit breakers for the range. Electric ranges have two breakers that are often but not always connected, so shut off both breakers. Open the door completely and remove the screws from the bottom front lip of the glass cooktop frame. Carefully pull the cooktop assembly slightly forward to release the front lip from the front support bracket. Lift the front of the cooktop to release the frame sides from the support bracket and then pull it forward to release the hinge tabs from the slots in the backguard. Lift the front edge of the glass cooktop and prop it open, placing the prop at the center of the cooktop’s front lip where it’s most stable. Be careful not to damage the oven insulation when propping open the cooktop. Disconnect the wires from the oven door switch. Use a slot screwdriver to release the locking tabs and pull the oven door switch out from the range frame. Push the new oven door switch into the range frame. Connect the wires to the new oven door switch. Carefully remove the prop and lower the cooktop. Tuck the front lip of the cooktop frame under the front support bracket and lower the sides over the ends. Push the cooktop back, inserting the hinge tabs into the backguard slots. Reinstall the mounting screws in the front lip of the cooktop frame. Close the oven door. Plug the power cord into the outlet or turn on the house circuit breakers for the range. If you pulled out the range to unplug it, slide the range into position, ensuring that the rear leveling foot fully connects with the anti-tip bracket.
This video from Sears PartsDirect shows how to replace an oven door switch in a range. The oven door switch shuts off the light when you close the door (unless you’ve set the light to stay on). It also verifies that the oven door is shut during the self-clean cycle. If the oven light stays on when you close the door or the self-clean cycle either won’t start or stops in the middle, replace the door switch with a manufacturer-approved part.
Visit us at:
https://www.searspartsdirect.com?sid=soc:youtube:replacing-a-range-oven-door-switch
Or call 1-800-437-1673 to speak with a parts specialist.
The video includes these parts and tools. Look up your model to make sure you get the right parts for your range.
Oven door switch
searspartsdirect.com/part-number/316445500/0022/628.html?sid=soc:youtube:card-direct-part-link
Find parts for your Range at:
searspartsdirect.com/partsdirect/product-types/Range-Parts?sid=soc:youtube:rangeparts
Or, click here to schedule an appointment with a repair technician.
searshomeservices.com/repair#showall
Transcript:
The first step is to unplug the range or shut off the circuit breakers for the range. Electric ranges have two breakers that are often but not always connected, so shut off both breakers. Open the door completely and remove the screws from the bottom front lip of the glass cooktop frame. Carefully pull the cooktop assembly slightly forward to release the front lip from the front support bracket. Lift the front of the cooktop to release the frame sides from the support bracket and then pull it forward to release the hinge tabs from the slots in the backguard. Lift the front edge of the glass cooktop and prop it open, placing the prop at the center of the cooktop’s front lip where it’s most stable. Be careful not to damage the oven insulation when propping open the cooktop. Disconnect the wires from the oven door switch. Use a slot screwdriver to release the locking tabs and pull the oven door switch out from the range frame. Push the new oven door switch into the range frame. Connect the wires to the new oven door switch. Carefully remove the prop and lower the cooktop. Tuck the front lip of the cooktop frame under the front support bracket and lower the sides over the ends. Push the cooktop back, inserting the hinge tabs into the backguard slots. Reinstall the mounting screws in the front lip of the cooktop frame. Close the oven door. Plug the power cord into the outlet or turn on the house circuit breakers for the range. If you pulled out the range to unplug it, slide the range into position, ensuring that the rear leveling foot fully connects with the anti-tip bracket.










