Uploaded February 2022 | Updated November 2026, 3 hours ago
We got this Sachs Wankel KM24 Rotary engine from eBay a couple years ago and we're finally ready to put it to good use! Last video we had low compression and it wouldn't start up, so we decided to take a look inside. There was some mild pitting and corrosion so we used a glass block and sandpaper to do a backyard lapping job on it which smoothed things out pretty nicely. We got rid of the grease that was in the seals and rebuilt the rotor with vaseline that will burn off cleanly. It ended up starting after the rebuild and sounds strong! Thanks for watching!
Build Break Repeat is Proudly Sponsored by GoPowerSports
**Be sure to check your local laws before driving any non-registered motorized vehicle. Do not attempt these activities at home. All content produced by Build Break Repeat is for entertainment purposes only**
CHECK OUT OUR INSTAGRAM! instagram.com/build.break.repeat?igshid=ulwwhmio96an
LINKS TO OUR NEW TOOLS AND EQUIPMENT: https://linktr.ee/BuildBreakRepeatChannel (Amazon Affiliate Links, if you buy something using our links it will help the channel!)
--------------TOOLS -------------
Tools we use and have received from sponsors:
Texas Metalworks 40x80 Welding Table
texasmetalworks.com/product/fully-fabricated-welding-table
RogueFab Tubing Notcher
roguefab.com/product/versanotcher-universal-tubing-notcher
Pro-tools Tubing Bender
pro-tools.com/collections/tube-and-pipe-benders
Optrel Crystal 2.0 Welding Mask
usa.optrel.com/en/eye_protection_helmets/products/show/crystal20
Optrel Grinding Mask
usa.optrel.com/en/products/augenschutz/helme-zum-schleifen-schneiden/products/show/clearmaxx
----------MUSIC ---------
Intro Song - Jimmi by Andrew Applepie
youtube.com/watch?v=l1zHz8pYfyQ&ab_channel=AndrewApplepie
---------MERCH----------
MERCHANDISE CUSTOM DESIGNED BY YOURS TRULY
teespring.com/stores/build-break-repeat
Time Stamps:
00:00 - 00:11 : Intro
00:11 - 03:24 : Lapping the Engine
03:24 - 11:07 : Rebuild
11:07- 13:00 : First Start
13:00 - 13:55 : Outro
We got this Sachs Wankel KM24 Rotary engine from eBay a couple years ago and we're finally ready to put it to good use! Last video we had low compression and it wouldn't start up, so we decided to take a look inside. There was some mild pitting and corrosion so we used a glass block and sandpaper to do a backyard lapping job on it which smoothed things out pretty nicely. We got rid of the grease that was in the seals and rebuilt the rotor with vaseline that will burn off cleanly. It ended up starting after the rebuild and sounds strong! Thanks for watching!
Build Break Repeat is Proudly Sponsored by GoPowerSports
**Be sure to check your local laws before driving any non-registered motorized vehicle. Do not attempt these activities at home. All content produced by Build Break Repeat is for entertainment purposes only**
CHECK OUT OUR INSTAGRAM! instagram.com/build.break.repeat?igshid=ulwwhmio96an
LINKS TO OUR NEW TOOLS AND EQUIPMENT: https://linktr.ee/BuildBreakRepeatChannel (Amazon Affiliate Links, if you buy something using our links it will help the channel!)
--------------TOOLS -------------
Tools we use and have received from sponsors:
Texas Metalworks 40x80 Welding Table
texasmetalworks.com/product/fully-fabricated-welding-table
RogueFab Tubing Notcher
roguefab.com/product/versanotcher-universal-tubing-notcher
Pro-tools Tubing Bender
pro-tools.com/collections/tube-and-pipe-benders
Optrel Crystal 2.0 Welding Mask
usa.optrel.com/en/eye_protection_helmets/products/show/crystal20
Optrel Grinding Mask
usa.optrel.com/en/products/augenschutz/helme-zum-schleifen-schneiden/products/show/clearmaxx
----------MUSIC ---------
Intro Song - Jimmi by Andrew Applepie
youtube.com/watch?v=l1zHz8pYfyQ&ab_channel=AndrewApplepie
---------MERCH----------
MERCHANDISE CUSTOM DESIGNED BY YOURS TRULY
teespring.com/stores/build-break-repeat
Time Stamps:
00:00 - 00:11 : Intro
00:11 - 03:24 : Lapping the Engine
03:24 - 11:07 : Rebuild
11:07- 13:00 : First Start
13:00 - 13:55 : Outro










