Insta360 GO + Beta95X V2 + THE DOG THAT LOVES DRONES! Mr ShutterBug 2020-09-09 | My Beta95X V2 and Insta360 Go just arrived. Time to have some fun! Click "SHOW MORE" for build info, links, and my initial impressions of this drone...Note:I post affiliate links when available. If you one of the links to make a purchase, then I can earn a small commission. It's an easy way for you to help support this channel at no cost to yourself. Thanks!The Insta360 GO Camera:- BetaFPV: bit.ly/3id5vbG- GetFPV: bit.ly/32fxulvThe Beta95X V2 Drone (as seen here):- BetaFPV: bit.ly/3gK8CX2The Beta95X V2 with DJI Digital FPV:- BetaFPV: bit.ly/3bmvxqkABOUT THE INSTA360 GO:I just got this camera. This footage came from my first few flights with it. The image quality is NOT as good as a GoPro, but it is cool that it can mount on such a small drone and you don't have to strip it down to reduce weight. A lot of the resolution is lost because it records a full 180 deg and then crops down to the 16:9 rectangle. Also, the compression makes things a bit blocky when things are moving fast. I scaled it up to 4K to get the best compression on YouTube. There is a phone app that lets you change the stabilization mode and even rotate or re-aim the shot (which is really cool) Unfortunately, the PC/Mac software is pretty useless. When I mount the camera sideways (like on this drone) and use "FPV Stabilization" mode, the video comes out sideways. You can fix that on the phone app, but not on the PC (weird). The camera also has some real limitation that you should know about. It only records for 5 minutes at a time, it only records 25 fps, there is limited in-camera storage, and the battery only lasts for a few flights before needing to recharge. It is a really interesting camera though. I'll probably have more interesting footage to show in the future. Stay tuned!ABOUT THE BETA95X V2 DRONE:It actually flies quite well for such a small whoop with an HD camera. I was happily surprised! It was pretty easy to control, but flying really slow is still a challenge. The "pusher" design seem to help in flight, but it can make it tricky to take off again after you turtle in the grass or dirt. I used a 450mAh 4S battery and was getting over 5 minutes of flight time (longer than the camera can record) on gentle flights. Note that the flight time will probably be lower if you use a naked GoPro and the DJI FPV system, but those are options.Music:Catch Me by InfractionWarm regards,Nate
Epic Whoop Racing with HDZero Digital FPV! Mr ShutterBug 2023-02-21 | I took my HDZero whoops to a race at Sumerian Brewing Co on Sunday, and it was a TON OF FUN! Good friends, intense competition, and a cool venue! I wasn't the only one racing with HDZero either. It seems like more and more people are making the switch. Very cool!Special thanks to Roger Ma, and to Dan an Liz Sugano for all their hard work organizing these events. And thanks to Roger for giving me permission to use his video footage of the race-off.If you want to help support this channel, here are some affiliate links you can use when shopping for FPV great. I make a small commission and it costs you nothing. Thanks!- GetFPV: http://bit.ly/2Ot4q2K- BetaFPV: http://bit.ly/betafpv-shutterbug- Banggood: http://bit.ly/2OVcf1rWant to see exactly how I built this HDZero Whoop? Full details here: youtu.be/hufEk1cLG1cI was also flying the Happymodel Mobula 6 HDZero, but I swapped the motors to 25,000KV 0802, and I swapped the battery connector to BT2.0 so I could use my Tattu 300mAh BT2.0 batteries (which are excellent batteries, by the way).Music:"Confidence" by Roman Senyk Music (used under license)
Find out if you won some FPV gear! Mr ShutterBug 2022-12-03 | Today I'm announcing the five winners from my last giveaway. If I announce your name, then please email me using the address on the about page of my YouTube channel! Thanks and good luck!
What to do when you have too much FPV gear... Mr ShutterBug 2022-11-20 | I have more FPV gear than I can use, so I'm giving some of it away. I hope this gear helps you enjoy FPV or to share the joy with someone in your life! See official rules below:If you want to help support this channel, here are some affiliate links you can use when shopping for FPV great. I make a small commission and it costs you nothing. Thanks!- GetFPV: http://bit.ly/2Ot4q2K- BetaFPV: http://bit.ly/betafpv-shutterbug- Banggood: http://bit.ly/2OVcf1rBlack Friday Deals:- BETAFPV: 20% off store wide (some exclusions apply). Nov 25-29, 2022. Code: NATE22BF Link: http://bit.ly/betafpv-shutterbug- Flywoo: 15% off store wide. Nov 24-30, 2022. No code needed. Link: http://bit.ly/3UX5R9t- GetFPV: Lots of big discounts changing day-to-day. No code necessary. Link: http://bit.ly/2Ot4q2K- Additional sales going on at www.pyrodrone.com, www.racedayquads.com, and others, so shop around.Today's Prizes:1) Flywoo CineRace 20 drone (http://bit.ly/3TSgzwA).2) Flywoo Firefly Hex Nano drone (http://bit.ly/3hWlLCG)3) BETAFPV Cetus Pro drone + Lite Radio 2 SE FrSky + VR02 FPV Goggles (similar to http://bit.ly/3Oo76fm)4) BETAFPV Lite Radio 2 SE ELRS 2.4GHz (http://bit.ly/3hRV0iB)5) BETAFPV ELRS 915MHz Micro TX Module + 2 ELRS 915MHz receivers (http://bit.ly/3giUbim)Official Rules:- The winner is responsible for the actual shipping cost. I will let you know what that is when I know your shipping address. For international shipments, the winner is also responsible for any additional fees imposed by customs. If you are unable/unwilling to pay, I will pick a new winner.- You must be 18 years old to win. If you are under 18 years of age, then you will need to put me in contact with your parent or guardian, who can win the prize for you. - Some of the prizes have been used. Each prize is offered "as is". No returns. No exchanges.- To enter, leave exactly one comment on this video. Please mention the prize(s) you want in order of priority (starting with your top choice). If you don't want to enter, you can still comment. Please just make your intention clear.- 5 winners will be selected on December 1st, 2022 using a random comment picker. - I will then assign each winner one prize based on their preferences. A winner may not get their top choice if multiple people want the same prize.- If you win, I will need to contact you. If there is an email listed on your YouTube channel's about page, then I will use it. Otherwise, my only option will be to reply to your public comment. Keep an eye on your YouTube notifications, so you don't miss it!- If I am unable to contact the winner after 48 hours, I reserve the right to select a different winner. I do not want this to drag on.- If you try to enter more than once, or I think you are a bot, or I think you are trying to cheat in any way, then I will pick a different winner, at my sole discretion.Good luck!Nate
Building an AMAZING 1S WHOOP with HDZERO: Full Details & Acro Flight Mr ShutterBug 2022-07-10 | I build a light weight racing whoop with the new HDZero 1S digital FPV components, and it is amazing! In this video, I cover the full build process, and some new flight footage, so keep watching to the end! Full parts, build notes, and related video links below...If you use my affiliate links to make a purchase, then I will make a small commission. It is a nice way that you can help support this channel, and it costs you nothing. Thanks!If you don't want to build from scratch, then consider the new Mobula6 HDZero 1S bind-n-fly:- From GetFPV (USA): bit.ly/3OUPMOQ- From Banggood: bit.ly/3nSXUUaThe new HDZero 1S VTX + Lite Camera can be purchased in a bundle:- From GetFPV (preorder, but I believe they are already in transit): bit.ly/3nO6Vh4 - From Banggood: bit.ly/3NTdJEDIf you don't already have an HDZero Receiver module, you can get one here:- From GetFPV: bit.ly/3yUXPoY- From Banggood: bit.ly/3IsVS6tFull Parts List:- HDZero 1S VTX + Lite Camera Bundle: bit.ly/3nO6Vh4 (getfpv), bit.ly/3NTdJED (banggood)- Frame I used this time: bit.ly/3Ipp1iQ- Frame I recommend (stronger, more room underneath): bit.ly/3LyfGpU)- Flight controller I used: bit.ly/3GNl5a2 (WARNING watch this PSA first: youtu.be/PKUAncsiP1U)- Motors I used: Happymodel 25,000KV EX0802: bit.ly/3yTWVta- Alternate motor: Happymodel 19,000KV EX0802 (lower KV may improve flight time): bit.ly/3ytnDYb- 31mm 3-blade HQ Props: bit.ly/3IovyKR- RENY M1.4 x 4mm motor screws: http://bit.ly/2P0JOzT- ORT Micro Vee antenna: bit.ly/3OY8WTN- If you use PH2.0 batteries, these are the good 90 degree connectors: http://bit.ly/2Jcu4GjCanopy SLT:thingiverse.com/thing:5431202Related Videos:- PSA about the FC firmware issue: youtu.be/PKUAncsiP1U- Indoor racing with this same build: youtu.be/6v67kSoFRfs- New HDZero VRX receiver module: youtu.be/2ReKraZHO34- My HDZero 2S toothpick build: youtu.be/YxDOrr-jt40- My HDZero 2S ShutterBug85 build: youtu.be/UgvgwyX5DgIMusic:"Go Down Swinging" by NEFFEX (YouTube Audio Library)What do you think of the new build? Let's chat in the comments!- Nate
PSA: You new BETAFPV FC could be PERMANENTLY RUINED unless you do this BEFORE plugging it in! Mr ShutterBug 2022-07-04 | Public Service Announcement: Unfortunately this BETAFPV F4 1S flight controller has been shipping with a bug. The first time you plug in a battery or USB cable, it will boot up and permanently alter the gyro chip making it unusable and unfixable! Fortunately, if you have not powered it up yet, then you can save it by holding the boot button to put it in DFU mode the very first time you connect USB. Then, you can flash it with an official release of Betaflight 4.3, which won't have this problem.For more information about the bug:github.com/betaflight/betaflight/pull/11584?fbclid=IwAR00ecXWZrwhV2HwlOGO5cO-81fKNW9888GPrMyEvHdSpa0b2JG7JJ0fgGII hope this helps someone out! Happy building!Nate
Crazy Fast! Crazy Fun! Racing & Crashing with a New HDZero Lite 1S Whoop. Mr ShutterBug 2022-06-25 | This is a brand new build with the up-coming HDZero Lite 1S Camera and VTX. I want to show you the ridiculous fun that I've been having flying around the house! Links and related videos below...You can also follow on Instagram for a glimpse into my projects before they hit YouTube: instagram.com/mrshutterbugIf you want to help support this channel, here are some affiliate links you can use when shopping for FPV great. I make a small commission and it costs you nothing. Thanks!- GetFPV: http://bit.ly/2Ot4q2K- BetaFPV: http://bit.ly/betafpv-shutterbug- Banggood: http://bit.ly/2OVcf1rRelated Videos:- Testing the new HDZero receiver module: youtu.be/2ReKraZHO34- A closer look at the new HDZero Lite camera & VTX: youtu.be/vcLz_ZzVBbs- My first HDZero 1S Whoop Build: youtu.be/44Bu2HgIWkM- My ShutterBug85 2S Whoop with HDZero: youtu.be/UgvgwyX5DgIMusic:"Young and Confident" by Roman Senyk Music
Testing the New HDZero SharkByte Video Receiver (Watch in 4K) Mr ShutterBug 2022-05-07 | I got a chance to test a prototype of the new HDZero video receiver module. I'll show you how it performed, and how it differs from the original. You can preorder the VRX now, if you're interested. Hopefully it will be in stock at retailers very soon. Links and info below:If you want to help support this channel, simply use these affiliate links when you shop for FPV gear. Thanks!- BetaFPV: http://bit.ly/betafpv-shutterbug- GetFPV: http://bit.ly/2Ot4q2K- Banggood: http://bit.ly/2OVcf1rRelated Videos:- New HDZero 1-3S VTX also coming soon: youtu.be/vcLz_ZzVBbs- My TWIG ET5 HDZero build: youtu.be/8a7R3w6SCws- My ShutterBug85 Whoop with HDZero: youtu.be/UgvgwyX5DgIGet the New HDZero VRX Module Here:bit.ly/3Kv6T6NAntennas I'm Using (great value!):- TrueRC Long SMA RHCP: bit.ly/3vQX7I7- AXII Stubby (XILO branding): bit.ly/3yoldvk- AXII Stubby (ALTERNATE in case the XILO version sells out): bit.ly/3FqyHYRWhat do you think? Let's chat in the comments.- Nate
Lightest Digital FPV Solution Yet! HDZero Lite Camera + 1S VTX! (COMING SOON) Mr ShutterBug 2022-04-30 | Runcam and Divimath got together to create the lightest digital FPV camera yet. It should be the perfect thing to go with the new 1S VTX. I can show you both of them today and they will be released publicly very soon! HDZero just keeps getting better! Links & info below:You can also follow on Instagram for more regular updates on my projects: instagram.com/mrshutterbugIf you want to help support this channel, simply use these affiliate links when you shop for FPV gear. Thanks!- BetaFPV: http://bit.ly/betafpv-shutterbug- GetFPV: http://bit.ly/2Ot4q2K- Banggood: http://bit.ly/2OVcf1rRelated Videos:- Nick Burns Flight Footage with the Cam + VTX: youtu.be/By20Dxft8oQ- My Previous HDZero 1S Whoop Build Video: youtu.be/44Bu2HgIWkM- My Custom HDZero whoop camera: youtu.be/nXgqhefFxWY- My Favorite 2S Whoop with HDZero: youtu.be/UgvgwyX5DgIRelated Products:- HDZero VRX Module (preorder): bit.ly/3Kv6T6N- HDZero Lite 1-3S VTX (coming soon)- HDZero Runcam Lite Camera (coming soon)- Beta65 Pro Whoop Frame (the one I used in my build): bit.ly/3LyfGpU
Can this HDZERO RACING WHOOP really compete? LETS FIND OUT! Mr ShutterBug 2022-02-24 | This 22.8 gram 1S WHOOP has HDZERO digital FPV. That's super cool, but is it light enough to be competitive at an analog whoop race? I took it to Sumerian Brewery to find out! Links and related videos below:You can also follow on Instagram for more regular updates on my projects: instagram.com/mrshutterbugRelated Videos:- My HDZero 1S Whoop Build Video: youtu.be/44Bu2HgIWkM- My Custom HDZero whoop camera: youtu.be/nXgqhefFxWY- My Favorite 2S Whoop with HDZero: youtu.be/UgvgwyX5DgIIf you want to help support this channel, simply use these affiliate links when you shop for FPV gear. Thanks!- BetaFPV: http://bit.ly/betafpv-shutterbug- GetFPV: http://bit.ly/2Ot4q2K- Banggood: http://bit.ly/2OVcf1rMusic:Sport Drive by Roman Senyk Music
Building an Ultra-Light Digital FPV Camera for HDZero / SharkByte Mr ShutterBug 2022-02-08 | With this new camera, my HDZero 1S Whoop is now just 22.8 grams, and it has the widest FOV I have ever seen on a digital FPV system! Full parts list below (click SHOW MORE).You can also follow on Instagram for more regular updates on my projects: instagram.com/mrshutterbugI accidentally damaged the 1S VTX in my build, but Daniel from ATX Airborne was kind enough to send me one of his. THANK YOU DANIEL! Go check out the HDZero content on his channel too!youtube.com/channel/UChgROMkzv8SmyoYq7OEpjLwRelated Videos:- My HDZero 1S Whoop Build Video: youtu.be/44Bu2HgIWkM- My Favorite 2S Whoop with HDZero: youtu.be/UgvgwyX5DgI- My Waterproof Whoop, which I mentioned in the video. Fun project! youtu.be/xhPZosNiWFoIf you want to help support this channel, simply use these affiliate links when you shop for FPV gear. Thanks!- BetaFPV: http://bit.ly/betafpv-shutterbug- GetFPV: http://bit.ly/2Ot4q2K- Banggood: http://bit.ly/2OVcf1rExact parts I used for this camera:- Runcam Nano HD Camera: bit.ly/3yGNVpn- Lens from a Wolfwhoop WT07 analog camera: amzn.to/2XV7g6a- NinjaTek Armadillo TPU: amzn.to/3HA1omLBuild Notes:- Camera: I used the older Runcam Nano HD camera. It has an orange body and a 14x14mm back plate. The newer Runcam/HDZero branded nano camera has a different size back plate (14x16mm) and a different size sensor. I also have the Foxeer Digisight V2. It could work but it is not as light even after you remove all the analog wires because the sensor itself is encased in a thicker piece of glass.- Lens: I like the WT07 lens because it is ultra wide. The downside is that you have to remove the glue to get it off. I used a tiny screwdriver to break through the glue and then pry it off in pieces. There are lots of other whoop cameras with the same size lens however. If it has an IR filter, then it will probably work. Pick your favorite and give it a try (if you're feeling brave enough to modify a $50 camera, that is).3D Printer Models:- STL file for the camera body I used: bit.ly/3oxEWTE- Remix the TinkerCad project if you want to modify the parameters: bit.ly/3GBrWlY- STL file for the updated camera mount: bit.ly/3rL3ZVvThanks for watching! This channel is something I do in my free time. It's a labor of love! Feel free to share the video link with other people if you think they would enjoy it too. :-)
The Worlds Lightest HD FPV Whoop is AMAZING! (HDZero/SharkByte 1S) Mr ShutterBug 2022-01-20 | The day has finally arrived when it is possible to build a 65mm 1S whoop racer with high definition FPV! I have a prototype of a 1S VTX that HDZero is developing. The final version will be even lighter! Check it out! Click "SHOW MORE" for links and related videos.You can also follow on Instagram for more regular updates on my projects: instagram.com/mrshutterbugIf you want to help support this channel, simply use these affiliate links when you shop for FPV gear. Thanks!- BetaFPV: http://bit.ly/betafpv-shutterbug- GetFPV: http://bit.ly/2Ot4q2K- Banggood: http://bit.ly/2OVcf1rRelated Videos:- My HDZero Nano Camera Review: youtu.be/U48jjmFtG1A- My HDZero ShutterBug85 2S Whoop Racer: youtu.be/UgvgwyX5DgI- My Lightest 65mm Analog Whoop (15.3 grams): youtu.be/Rz0MjU4Gg3A- My Lightest 75mm Analog Whoop (16.8 grams): youtu.be/0P3PREMKdDcVideo Receiver Module- HDZero VRX Module (updated model) should be in stock soon. Preorder one now before they sell out again: bit.ly/3Kv6T6NVideo Transmitter:- HDZero Lite Whoop VTX 1-4S (coming soon)Camera:- I used the Runcam Nano HD Camera: bit.ly/3FJrF0a With this glass M8 lens: bit.ly/3qK3oCN- I recommend the HDZero Nano Camera (better picture): bit.ly/3yGNVpn (GetFPV), bit.ly/3rghkDr (Banggood)Frame:- Beta65 Pro V3 (discontinued, but maybe you can still find it)- I believe the Mobula6/BWhoop65/UR65 frame could also work: bit.ly/3ImvCJE (GetFPV), Banggood (bit.ly/3Ai3aFW)Flight Controller:- BetaFPV F4 1S 5A AIO with ELRS 2.4GHz: bit.ly/3GNl5a2 Motors:- Happymodel EX0802 Unibell Motors 19000KV or 22000KV: bit.ly/3FLtp9d (GetFPV), bit.ly/3Ai57SM (Banggood)- Or use any other 0802 motor of similar specs.Hardware:- 40mm MIPI Cable (wish it was even shorter): bit.ly/3fEkzPF (GetFPV), bit.ly/3rzdeXh (HDZero)- RENY M1.4 x 4mm motor screws: http://bit.ly/2P0JOzT- PH2.0 90-Degree Connector by JST (the real one): http://bit.ly/2Jcu4GjSLT Files:- Whoop Camera Mount (as seen in this video): bit.ly/32tTTyk- If you want to use the new HDZero Nano camera with 14x16mm back plate, then here's a canopy you could consider: bit.ly/3GWXhRgMusic:Higher Octane by Vans In Japan (YouTube Audio Library)Bad Ideas - Silent Film Dark by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 license. https://creativecommons.org/licenses/by/4.0/Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1100489Artist: http://incompetech.com
The HDZero Nano Camera is Amazingly Clear! Mr ShutterBug 2021-12-19 | This new generation of HDZero cameras take the Shark Byte system to a new level and this one is only 4 grams! It's great to see the system continue to improve! I tried it out in my Digital ShutterBug85 build and... yeah... count me impressed! Links and info below!You can also follow me on Instagram to see what I'm up to. I post pretty often these day: instagram.com/mrshutterbugProducts Show In This Video (Affiliate links help me out if you use them. Thanks!):- HDZero Nano Camera: bit.ly/3yGNVpn (GetFPV), bit.ly/3rghkDr (Banggood)Related Videos:- My 85mm HDZero Whoop Build: youtu.be/UgvgwyX5DgI- My 3-inch HDZero Toothpick Build: youtu.be/YxDOrr-jt40- MultiGP Global Qualifier with HDZero: youtu.be/qH_HbmN4UToMusic:"That One Bar Scene" by RKVC (YouTube Audio Library)
Giveaway Results! DID YOU WIN? Mr ShutterBug 2021-12-14 | Thanks for all the kind words an encouraging comments! The FPV community is great! This video announces the winners of my latest giveaway contest. For full details see the original video: youtu.be/g9NVBdxt-jsYou can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugIf I named you as a winner, then please email me at mrshutterbug@yahoo.com. Once I get your mailing address, I'll look up the exact shipping cost so you can pay for shipping. I hope to hear from you soon!Nate
Im Giving Away Custom Built Drones and a Cetus Pro Starter Kit! Mr ShutterBug 2021-12-07 | I have more drones than I need, so I'm giving some of them away! This includes 3 drones that I built and a Cetus Pro FPV Starter Kit! If one of these drones would make your day, then I hope you win it! Contest rules below:You can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugPrizes:1) Cetus Pro FPV Starter Kit (my review of the original Cetus Kit: youtu.be/m5okvHrz9-U)2) Primo 3 Custom Build (as seen here: youtu.be/xq4j4XRgCNg)3) Beta85X Custom Build4) Beta95X Custom Build + Caddx Turtle V2Official Giveaway Contest Rules:- The winner is responsible for the actual shipping cost. I will let you know what that is when I know your shipping address. For international shipments, the winner is also responsible for any additional fees imposed by customs. If you are unable/unwilling to pay, I will pick a new winner.- The prizes have been used. Some of them show signs of wear. Each prize is offered "as is". No returns. No exchanges.- To enter, leave exactly one comment on this video. Please mention the prize(s) you want in order of priority (starting with your top choice). If you don't want to enter, you can still comment. Please just make your intention clear.- 4 winners will be selected on December 13th, 2021 using a random comment picker. - I will then assign each winner one prize based on their preferences. A winner may not get their top choice if multiple people want the same prize.- If you win, I will need to contact you. If there is an email listed on your YouTube channel's about page, then I will use it. Otherwise, my only option will be to reply to your public comment. Keep an eye on your YouTube notifications, so you don't miss it!- If I am unable to contact the winner after 48 hours, I reserve the right to select a different winner. I do not want this to drag on.- If you try to enter more than once, or I think you are a bot, or I think you are trying to cheat in any way, then I will pick a different winner, at my sole discretion.Good luck!Nate
Can Quicksilver Make Me A Better Whoop Racer? I Want To Find Out! Mr ShutterBug 2021-11-25 | Quicksilver is a relatively new firmware option from some of the same devs who brought you NFE_Silverware. It supports brushless motors and a variety of F4 flight controllers. It even has a nice Configurator and OSD menu system! You can probably flash it onto one of your existing builds, but why would you? For me, the answer comes down to one killer feature for angle mode racing. It can take a hard hit and recover in the air without losing track of which way is up! No more "drunk gyro" syndrome! I hope to tell you more about this and other features in future videos, so make sure you're subscribed. Links and info below...You can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugWant to help support this channel? Simply bookmark any of these links and use them when you shop for FPV gear. Each time you make a purchase, they will give me a small commission. It is totally free for you and it helps me get parts for future projects. Thanks! Banggood: http://bit.ly/2OVcf1r BETAFPV: http://bit.ly/betafpv-shutterbug GetFPV: http://bit.ly/2Ot4q2K Heli-Nation: http://bit.ly/heli-nationWant to try QUICKSILVER for yourself? Download Quicksilver Configurator: bit.ly/3DRo5Rr Download Quicksilver firmware through the Configurator or from: bit.ly/3DTikCD Quick Start Guide: bit.ly/3nPdzEuI can make a video showing my exact setup in a later video. Comment below if you're interested in that. Have a great Thanksgiving weekend everyone!P.S. I mentioned Black Friday deals, but those have now expired. Sorry.Music:"Epic Tension" by Roman Senyk Music (used under license)
X-Knight 35 HD Review & Flight Mr ShutterBug 2021-11-16 | What do you think of 3.5-inch as a way to stay under the 250 gram threshold for DJI FPV freestyle? The X-Knight 35 HD is BETAFPV's entry into the category. In this review, I'll show you what it can do and tell you what I like and what I don't. Links and discounts below:You can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugWant to help support this channel? Simply bookmark any of these links and use them when you shop for FPV gear. Each time you make a purchase, they will give me a small commission. It is totally free for you and it helps me get parts for future projects. Thanks! Banggood: http://bit.ly/2OVcf1r BETAFPV: http://bit.ly/betafpv-shutterbug GetFPV: http://bit.ly/2Ot4q2K Heli-Nation: http://bit.ly/heli-nationGear in this video:- X-Knight 35 HD BNF Drone: bit.ly/30w728U- DJI FPV Goggles: bit.ly/3HsA8a4- Tattu R-Line 850mAh 4S batteries: http://bit.ly/2IRwJ7L
What if every community had an FPV ZONE like this? Introducing Emerald City Drones! Mr ShutterBug 2021-11-12 | This is a brand new venue for indoor FPV and it looks amazing! Never flown before? That's OK. You can walk in, rent some equipment, and start experiencing FPV right away! I hope this really catches on. I would love to see venues like this pop up in more places! Comment below or head over to their Facebook page to leave your suggestions, questions, and words of encouragement for the owners who are taking on this exciting new venture!You can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugWant to help support this channel? Simply bookmark any of these links and use them when you shop for FPV gear. Each time you make a purchase, they will give me a small commission. It is totally free for you and it helps me get parts for future projects. Thanks! Banggood: http://bit.ly/2OVcf1r BETAFPV: http://bit.ly/betafpv-shutterbug GetFPV: http://bit.ly/2Ot4q2K Heli-Nation: http://bit.ly/heli-nationEmerald City Drones is in Arlington, Washington. More info on Facebook:facebook.com/Emerald-City-Drones-107292245083178Related Videos:- Beta95X V2 + SMO 4K camera (youtu.be/PfAYUU4pZB8)- ShutterBug85 + SharkByte (youtu.be/UgvgwyX5DgI)Music:"City Lights" by Roman Senyk Music (licensed)
FPV Racing by Trial & Error Mr ShutterBug 2021-10-30 | What's everybody flying for indoor whoop racing these days? I'll probably be putting together some new builds soon, but in the meantime I'm still love'n this 18.6 gram build with Emuflight. If you haven't seen it already, then check out this other video for more info and a full parts list: youtu.be/VhsvYXe-hZoMusic:"Time is Up" by Roman Senyk Music (licensed)
Whoop Racing is BACK! Mr ShutterBug 2021-10-25 | A new season of indoor whoop racing has begun at Sumerian Brewing with FPV Racing Seattle! I'm excited! It's been WAY too long! If you want to show your support, then don't forget to like and sub!Music:"The Perfect Place" by Roman Senyk Music (used under license)
Racing the Official MultiGP Qualifier with Digital FPV! Mr ShutterBug 2021-08-18 | It has been way too long since my last 5" drone race, so today I'm trying to shake off the rust and put some times on the MultiGP 2021 International Qualifier track! It's going to be epic! I'm flying a brand new Floss racer with a custom build of Betaflight 4.3 optimized for 500Hz ExpressLRS, plus I get to use Shark Byte digital FPV! I may not be the fastest racer out there, but it's a good chance to put the latest cutting edge tech to the test!My FPV video was great! I've never been able to see the track so clearly! Latency of Shark Byte feels just like analog with a rock solid 60Hz frame rate. Fortunately, my digital video did not cause any interference for analog pilots and it worked perfectly with the timing system too. It's really the perfect thing for racing! I hope they start allowing Shark Byte at all levels of MultiGP racing!I'm also using a custom build of Betaflight 4.3 with a custom tune and ExpressLRS running at 500Hz. Running your input that fast creates extra noise, so properly handling that noise is key to having the fastest RC link in the world! I collaborated with Chris Thompson (Betaflight dev) to get this one dialed in. I hope to share more details about that in the not too distant future, so stay tuned!STL File for Shark Byte VTX Mount:thingiverse.com/thing:4935577Music:"Heroic Feat" by Roman Senyk Music (licensed)Huge thanks Olympia FPV for hosting this event! It was awesome!Thanks for watching. Take care everyone!Nate
Ripn Packs + Shark Byte M12 Lens Mod Mr ShutterBug 2021-07-17 | I was out doing a bit of racing practice and decided to take a break and fly my TWIG ET5, which was recently upgraded with Shark Byte digital FPV and the M12 Ratel 1.66mm lens mod. It makes it hard to go back to analog FPV on my racing build. More info and related videos below...Fun Fact:This Shark Byte ET5 build got lost in a tree for a few days. I finally found it thanks to my friend Clif who did a fly-over with his DJI camera drone. Once I knew where it was, it was easy to get down. Crazy how well these things can hide sometimes!Related Videos:- Parts and Info about this ET5 build: youtu.be/5sJYGE7f6GU- My 1st Shark Byte build (a Babytooth): youtu.be/YxDOrr-jt40- My 2nd Shark Byte build (a ShutterBug85 Whoop): youtu.be/UgvgwyX5DgIRyan Quellet's Tutorial for the M12 Lens Mod: youtu.be/E1BqN_Ttv44Music:"Sport Drive" by Roman Senyk Music (used under license)
IGOW3 is Almost Here! 5 Reasons You Should SIGN UP NOW! Mr ShutterBug 2021-06-27 | IGOW Season 3 is right around the corner! Get your registration in by July 2nd, and get your WHOOP ON! I'll see you there! Links below:IGOW3 Registration Form: bit.ly/3qrSaRJIGOW3 Details: https: //bit.ly/3jdesFcIGOW Discord bit.ly/3w0qRyMIGOW Entry Video: youtu.be/BMzcj9refbESupport IGOW on Patreon: bit.ly/3x1sUEn
Cetus FPV Starter Kit Review & Giveaway Mr ShutterBug 2021-06-07 | The Cetus Kit is designed to help new pilots get off the ground and start enjoying FPV, even with no prior experience. In addition to reviewing the kit, I'm also doing a giveaway, so be sure to watch to the end! Product details and full contest rules below:No YouTube ads. No affiliate links. FPV is my hobby and this YouTube channel is a labor of love! Like & sub if you want to show your support and see more content in the future!Related videos you might enjoy:- My review of the BETAFPV Lite Radio 2: youtu.be/WQOGe1bXeao- Range testing with the Lite Radio 2: youtu.be/N17OePbO0mw- A cool example of indoor drone racing: youtu.be/dN_4suzyWTcCetus Kit (official product page):betafpv.com/collections/ready-to-fly-fpv-whoop-kits/products/cetus-fpv-kitAdditional accessories to consider:- More batteries: betafpv.com/collections/batt-1s/products/bt2-0-300mah-1s-30c-battery-8pcs- Battery Charger (charge 6 at once): betafpv.com/collections/batt-1s/products/bt2-0-connector-lipo-charger-board?variant=31321061490822Official Giveaway Contest Rules:- The giveaway prize is a Cetus FPV Kit. It includes the carrying case, drone, goggles, controller, and a few accessories.- The prize has been lightly used. It is offered "as is". No returns. No exchanges. If you have a problem with the product, take it up with Betafpv.- To enter, leave exactly one comment on this video. Please mention the prize or the giveaway so that I know that you want to enter. If you don't want to enter, you can still comment, just make your intention clear.- A winner will be selected on June 19th, 2021 using a random comment picker.- If you win, I will need to contact you. If there is an email listed on your YouTube channel's about page, then I will use it. Otherwise, my only option will be to reply to your public comment. Keep an eye on your YouTube notifications, so you don't miss it!- If I am unable to contact the winner after 48 hours, I reserve the right to select a different winner. I do not want this to drag on.- The winner is responsible for the actual shipping cost. I will let you know what that is when I know your shipping address. If you are unable/unwilling to pay, I will pick a new winner.- For international shipments, the winner is also responsible for any additional fees imposed by customs.- If you try to enter more than once, or I think you are a bot, or I think you are trying to cheat in any way, then I will pick a different winner, at my sole discretion.- Good luck!
Building an AMAZING Racing Whoop with Shark Byte Digital FPV (ITS SO MUCH FUN!) Mr ShutterBug 2021-05-15 | You wouldn't even know that this "ShutterBug85" build has Shark Byte because the components are contained neatly within the frame. It's my most durable design yet, and it's ridiculously fun to fly around my yard! Links and info below...Related Videos You Might Like:- Securing Your Props With Dental Floss: youtu.be/DJdi-Lvu6xE- My Shark Byte Babytooth Build: youtu.be/YxDOrr-jt40- My First ShutterBug85 Video (more than 2 years old): youtu.be/4uhbz7J9rH0- My Review of the Beta85 Pro 2: youtu.be/sq9TCmiP4Dw- My Fully Waterproof ShutterBug85: youtu.be/xhPZosNiWFo- My Lightest 75mm Whoop Build: youtu.be/0P3PREMKdDc- My Lightest Whoop Period: youtu.be/Rz0MjU4Gg3ABatteries:If you fly on high throttle like me, then it is pretty hard on batteries. Racing flights were just 2-3 minutes depending on the battery. For fast racing or hard outdoor freestyle, I recommend top notch 2S batteries in the 450-650mAh range. Examples:- Tattu R-Line 95C 550mAh 2S- GNB 600mAh 90C HV 2S (yellow label)Canopy SLT File (should work with most other 14x14mm cameras too):thingiverse.com/thing:4860098ShutterBug85 Parts List (2S Shark Byte version as seen here):- BetaFPV Beta85X 4K frame: betafpv.com/products/beta85x-4k-frame-kit- BetaFPV 1103 11,000KV motors: betafpv.com/products/1103-brushless-motors?variant=14762596007980- I used the JHEMCU Play4 AIO FC (leave the motor plugs off, or you probably won't be able to fit it under the frame like I did): racedayquads.com/products/jhemcu-play-f4-1-2s-aio-toothpick-whoop-flight-controller-w-5a-4in1-esc- WARNING: Several people have told me that the JHEMCU board died after few flights. Unfortunately every other AIO can also fail. None are perfectly robust. If you want something a little better, then I suggest the BetaFPV F405 (see 3S version below).- Shark Byte TX5S.1 VTX: pyrodrone.com/products/fatshark-sharkbyte-tx5s-1-video-transmitter- I used the Foxeer Digisight V2 Camera: pyrodrone.com/products/foxeer-digisight-2-nano-720p-digital-analog-4ms-latency-super-wdr-fpv-camera- But I recommend the Runcam Nano HD Camera because it is lighter and you don't have to remove any analog wires: pyrodrone.com/products/runcam-shark-byte-nano-hd-fpv-camera- 55mm MIPI Cable: pyrodrone.com/products/caddx-turtle-mini-v2-replacement-camera-cable-90mm- iFlight Sigma RHCP antenna: pyrodrone.com/products/iflight-sigma-5-8ghz-60mm-rhcp-lhcp-fpv-antenna-ipex-ufl- Emax Avan 2-inch Props (blue): racedayquads.com/products/avan-micro-2-prop-set-of-12-props-2x2-4x4- I used two 100uF capacitors. One on the FC's VBAT, one on the VTX. pyrodrone.com/products/16v-100uf-capcitor-for-micro-esc-aio-boards- Canopy attaches with whoop style screws. The one in front needs a smaller head. betafpv.com/products/screws-and-rubber-dampersShutterBug85 Analog Version:If you are using analog FPV, then your performance will be even better because of the reduced weight. In that case, you can mount the FC on top, like normal. You can use the same canopy with any 14x14mm camera, but you might need to adjust the position of the screw holes depending on the length of your lens.ShutterBug85 3S Version (batteries tend to be heavier, but you will have less voltage sag):- BetaFPV 1103 8000KV Motors: betafpv.com/products/1103-brushless-motors?variant=14735142682668- BetaFPV 12A F405 Whoop FC (you will have to remove the motor plugs if you want to make it fit under the frame like I did): betafpv.com/products/f405-20a-aio-2-4s-brushless-flight-controllerblheli_s-v3?variant=34899934347398- Otherwise the same as aboveCustom Betaflight 4.3 Tune:My new tune is a work-in-progress. You're welcome to use it, but you do so at your own risk. Be careful and check for hot motors before you go crazy with it. Feedback is welcome! I'm using a nightly build of Betaflight 4.3.0 and the Betaflight Configurator 10.8.0 since they have not yet been officially released. You can take a chance and try them out now, or you can wait for the official released when the bugs (if any) have been worked. For details on my current tune, refer to the following document. I may update it over time if I make further adjustments:docs.google.com/document/d/1VEBbydEdMqArFdzowkmbkVldBjdD70zdj5f8idEHmJA/edit?usp=sharingMusic:"Start Your Engines" by Ethan Meixsell (YouTube Audio Library)"Higher Octane" by Vans in Japan (YouTube Audio Library)
Building My New Favorite HD Toothpick with Shark Byte Digital FPV (Ultra Low Fixed Latency) Mr ShutterBug 2021-04-15 | How good is the Shark Byte digital FPV system for backyard freestyle? I'm about to find out! SPOILER: It's AWESOME! Click "Show More" for links and additional information.You can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugWant to help support this channel? Simply bookmark any of these links and use them when you shop for FPV gear. Each time you make a purchase, they will give me a small commission. It is totally free for you and it helps me get parts for future projects. Thanks! Banggood: http://bit.ly/2OVcf1r BETAFPV: http://bit.ly/betafpv-shutterbug GetFPV: http://bit.ly/2Ot4q2K Heli-Nation: http://bit.ly/heli-nationRelated Videos You Might Enjoy:- My DJI "Digitooth" build: youtu.be/vDBbhD3a55Y- My review of the Happymodel Crux 3: youtu.be/d8LiEtV77Ag- My 33 gram 1S Babytooth build: youtu.be/obns6k1xhIc- My 19 gram 1S "NanoBug": youtu.be/dKAU1N68UOE- How to fix the motor direction and mapping when mounting the FC in a different orientation: youtu.be/Aoy9-_ja7PwGetting Started with Shark Byte:- Any FPV goggles or display with HDMI input. I have Fat Shark HDO2.- FatShark Shark Byte RX5.1 Receiver Module: bit.ly/3acLQ9O- Two SMA antennas of your choice to go on top of the RX. They should be RHCP to match the patch antennas that are built-in.Parts I Recommend (not exactly what I used):- Shark Byte TX5S.1 single board digital VTX: bit.ly/2PW8eNR- Runcam Nano HD Camera: bit.ly/3e1GgIp or Foxeer Digisight V2 (I have not used it, but it is another option): bit.ly/32iNcLD- 55mm MIPI Cable (shorter than the one that comes with the camera): bit.ly/3uR8Rqv- FPVCycle Babytooth 3" Frame (2mm thick version): bit.ly/2Q3zEBi- FPVCycle 13mm 7700KV Motors (if you can find them in stock): bit.ly/2XWcOvQ OR Happymodel 1202.5 6400KV Motors (what I used here): bit.ly/3wZFdkG OR other motor with similar size and KV.- BetaFPV 12A F405 Whoop AIO. It is light and has good features. It also has motor plugs, which you could use or remove: bit.ly/3acAjr5 OR BetaFPV 20A F405 Toothpick AIO for an even easier and more robust build: bit.ly/3mPbiqR- Gemfan 3018 2-blade props (1.5mm shaft or 2mm shaft depending on your motors): http://bit.ly/2T9KkNW or Gemfan 3016 3-blade props (these fly smoother, but they have less power for pulling out of dives): http://bit.ly/36REC7a- RHCP Singularity Antenna with U.FL (I recommend not using the "short" one. It is harder to get a good antenna placement): bit.ly/3uMgi2e- Crossfire Nano Receiver (or receiver of your choice): bit.ly/3mO7ZAa- Crossfire Minimoral T V2 Antenna (or whatever goes with your receiver): bit.ly/3dhfmx0- Velcro Cable Ties for battery strap: amazon.com/dp/B001E1Y5O6- Cloth Tape: amazon.com/gp/product/B01NA8TIJ5- M2 x 4mm motor screws (titanium or steel)- M2 x 15mm stack screws (titanium or steel)- Thin foam battery pad helps it stay put: Flight Times:The main flight in this video used a GNB 300mah 80C 2S Battery. When flying fast hard freestyle like this I typically get:- 300mAh 2S = 3 minutes- 450mAh 2S = 4-5 minutes- 550mAh 2S = 5 minutes+Canopy STL Files:thingiverse.com/thing:4829635Betaflight 4.2.8 Tune:set gyro_lowpass2_hz = 375set dyn_lpf_gyro_min_hz = 300set dyn_lpf_gyro_max_hz = 750set dshot_idle_value = 700set dshot_bidir = ONset motor_pwm_protocol = DSHOT300set motor_poles = 12set yaw_motors_reversed = ONset pid_process_denom = 4profile 0set dyn_lpf_dterm_min_hz = 105set dyn_lpf_dterm_max_hz = 255set dyn_lpf_dterm_curve_expo = 7set dterm_lowpass2_hz = 225set vbat_pid_gain = ONset iterm_relax_cutoff = 20set yaw_lowpass_hz = 100set throttle_boost = 7set throttle_boost_cutoff = 25set p_pitch = 55set d_pitch = 39set f_pitch = 124set p_roll = 50set d_roll = 36set f_roll = 117set p_yaw = 54set f_yaw = 117set d_min_roll = 0set d_min_pitch = 0set ff_spike_limit = 70set ff_smooth_factor = 20Bluejay ESC Tune:- PWM = 24kHz- Startup Power = 1061 min, 1243 max (equivalent to a single value of 1.25 in BLHeli_S)- Motor Timing = Medium HighMusic:- "Funny Stories" by Roman Senyk Music (licensed)- "Action Trailer" by Roman Senyk Music (licensed)- "Burlesque Heartache" by RKVC (YouTube audio library)
Crux3 + Insta360 GO | Lets see what it can do! Mr ShutterBug 2021-03-26 | Trying out the Happymodel Crux3. The specs are very similar to a Babytooth, but the motor KV is lower because it is designed for 2S. Lets put it to the test and find out what it can do! Product links and related videos below...Product Links (affiliate links when available):- Happymodel Crux3 Drone: (banggood: bit.ly/3dbY6rN, getfpv: bit.ly/31lpOgk)- Replacement Frame (banggood: bit.ly/3spKKyx, getfpv: bit.ly/3d6equ0)- Replacement Canopy (banggood: bit.ly/2QFZwTP, getfpv: bit.ly/3rolpDG)- Minimortal-T V2 Crossfire Antenna: bit.ly/39gDRrKRelated Videos You Might Like:- 2S "Digitooth" (very similar to the Crux3 but with DJI Digital FPV): youtu.be/vDBbhD3a55Y- 1S Babytooth with Insta360 GO (yes it can carry it!): youtu.be/xP6_M2EYi1E- My 33 gram Babytooth build video: youtu.be/obns6k1xhIc- Some insane 1S Babytooth flight footage: youtu.be/bUUcPVNV2AAMusic:"Win the Day" by Roman Senyk Music (licensed)
How to Mount Your FC in Any Orientation (AND WHY I DO THIS SO OFTEN) Mr ShutterBug 2021-03-22 | Once you realize you can mount your FC and/or ESC in any orientation, it opens up a lot of possibilities for custom builds. Here's how I do it! Links to related videos below:Videos About My Custom Builds Shown in this Video (in the order they appeared):- The little drone with purple props: youtu.be/dKAU1N68UOE- 1S Babytooth (one of my all time favorites): youtu.be/obns6k1xhIc- 2S Digitooth (Babytooth with DJI FPV): youtu.be/vDBbhD3a55Y- The Tiny 2S Drone from 2018: youtu.be/dW41xCLvzO0- My First 2S Whoop (before 2S Whoops were a thing): youtu.be/PlYAdDGasP0- Super G DJI 5" drone (No video on that one. Do you want to see it fly?)Related Videos by Joshua Bardwell (and way more info on his channel, of course):- Installing and using Betaflight & BLHeli configurators: youtu.be/bAqgPEW48Tc- Resource Remapping in Depth: youtu.be/gL1DxUFjFq8
How I Converted My Nanohawk into Something AMAZING! (with 40mm PROPS) Mr ShutterBug 2021-03-10 | I converted my EMAX Nanohawk to a toothpick-style drone and increased the prop size to 40mm. It’s super fun! I call it my "NanoBug"! Parts list and links below.You can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugWant to help support this channel? Simply bookmark any of these links and use them when you shop for FPV gear. Each time you make a purchase, they will give me a small commission. It is totally free for you and it helps me get parts for future projects. Thanks! Banggood: http://bit.ly/2OVcf1r BETAFPV: http://bit.ly/betafpv-shutterbug GetFPV: http://bit.ly/2Ot4q2K Heli-Nation: http://bit.ly/heli-nationHere's my review of the EMAX Nanohawk, in case you haven't seen it: youtu.be/wnb2eKkTGa8STL Files: thingiverse.com/thing:4779696Parts List (affiliate links, when available):- EMAX Nanohawk BNF drone: http://bit.ly/3rxQJkt- EMAX 300mah 1S batteries: http://bit.ly/3qxJo2Q- BeeBrain V2 Canopy: http://bit.ly/37qLvMd- HQ 40mm 2-blade props: http://bit.ly/3vjbz9B- Reny M2 12mm screws (cut to length or use metal screws): bit.ly/3au3KD5- Replacement Nanohawk Frame: bit.ly/396IVirPowerPlay DVR used to record 60Hz FPV: http://bit.ly/power-play-dvrIf you convert a Nanohawk just like I show in this video, and you mount your props in the reverse direction (sometimes called "props out"), and you flash Emuflight 0.3.3, then you can use my full CLI dump: bit.ly/3ARdHHOHere are the CLI to rotate board and remap motor (may require fixing the motor direction in ESC firmware). Works with any FC running Emuflight or Betaflight:resource MOTOR 1 B07resource MOTOR 2 B08resource MOTOR 3 B10resource MOTOR 4 B06set align_board_yaw = 90set yaw_motors_reversed = ONMusic:“Future Pop” by Roman Senyk Music (Creative Commons License)“Get Tough” by Track Tribe (YouTube Audio Library)
FPV Soccer Goal Challenge (MUD EVERYWHERE! DONT CRASH!) Mr ShutterBug 2021-02-22 | This is where they store all the soccer goals for the winter. I've been meaning to come here for a while, but I had just a short break in which to fly. Time to make the most of it! Info and related videos below...I was flying a TWIG Mutant 4" with the Caddx Vista (DJI FPV system). I've shown it on the channel before. Check out the following videos if you haven't already! The build is pretty much the same today, except that I'm using the HQ 4x2x3 props.Footage recorded by DJI FPV goggles (same as my view while flying).Build Explanation & Parts List Here:youtu.be/2nJNUvtuH84More Flight Videos:- "TWIG Mutant + Digital FPV + Awesome New Flying Spot!" youtu.be/9YtAKhKxTdc- "Crazy Fun with my DJI TWIG Mutant 4-inch" youtu.be/nfqloFW-zhUMusic:"We Need A Miracle" by ONLAP:open.spotify.com/track/33W6nFqHIhVCfGLiafK3kryoutube.com/channel/UCDu5kwaUa5eokd1ugr8-IoAinstagram.com/onlap_musicsoundcloud.com/onlapmusictwitter.com/OnlapMusicfacebook.com/ONLAP.OfficialMusic provided by RFM: youtu.be/76_RsyQaxUI
EMAX Nanohawk + GNB27 | Hands-On Review Mr ShutterBug 2021-02-17 | The EMAX Nanohawk is a curious little drone. It looks like a whoop, but it actually has a carbon fiber frame and differently shaped guards. Also, it has the new GNB27 battery connector. Do those things make it better than a typical whoop? Yes and no. Here's my full hands-on review. Links and info below...EMAX Nanohawk Drone: - Banggood: http://bit.ly/3s4YkH6- GetFPV: http://bit.ly/3ppMrd3Extra EMAX Props:- Banggood: http://bit.ly/3dpwr8q- GetFPV: http://bit.ly/2NAYQh3Extra EMAX Batteries:- Banggood: http://bit.ly/3douMjm- GetFPV: http://bit.ly/3u7J7qnTinyWhoop Cube Gates (are AWESOME!):bit.ly/2KUcnPQI'm using an Emuflight Tune with Dual-Axis Steering. For more info, check out this video:youtu.be/VhsvYXe-hZoIf you want my full CLI dump, here it is. Requires Emuflight 0.3.3 with reversed motor direction ("props out"):http://bit.ly/3bd682tMusic:"Crazy Idea" by Roman Senyk MusicCreative Commons Licensepatreon.com/romansenyk
Crazy Fun with my DJI TWIG Mutant 4-inch Mr ShutterBug 2021-01-26 | This drone isn't new, but it sure is fun! I wasn't planning to release this footage when I recorded it, but it was one crazy ride! Hope you enjoy it! I've show this build in more detail before. Links & info below:Related Videos:- This DJI Twig Mutant build info here: youtu.be/2nJNUvtuH84- More EPIC flight footage here: youtu.be/9YtAKhKxTdcFull Parts (affiliate links when available):- TWIG Mutant frame: http://bit.ly/3cQeVY5- TWIG Megabat Vista Canopy: phx-3d.com/racerx- BetaFPV F4 2-4S 20A AIO FC (there is a newer F405 version now): http://bit.ly/betafpv-20a-aio-v3- BetaFPV 1505 3600KV Motors (Nice and light, but I think a slightly larger motor would give it more low-throttle stability): http://bit.ly/betafpv-1505-3600kv-motors- Caddx Vista: http://bit.ly/3aZv78u- TBS Crossfire Nano Receiver: http://bit.ly/3aJgC7O- Tattu R-Line 850mAh 4S Battery: http://bit.ly/2IRwJ7L- HQ 4x2x3 T-Mount Props (I haven't use these before, but they are great! Very smooth response!): bit.ly/2ZFkQcXMusic:ONLAP - Everywhere I Goopen.spotify.com/track/33W6nFqHIhVCfGLiafK3kryoutube.com/channel/UCDu5kwaUa5eokd1ugr8-IoAinstagram.com/onlap_musicsoundcloud.com/onlapmusictwitter.com/OnlapMusicfacebook.com/ONLAP.OfficialMusic provided by RFM: youtu.be/G0k2oYR0CjQ
Announcing the WINNERS of my giveaway contest Mr ShutterBug 2021-01-24 | If you were selected as a winner, please contact me by email using the email address listed on the about page of my YouTube channel. Thanks for all the kind words and enthusiasm everyone!For more information and official rules, please refer to the original giveaway video:youtu.be/xNNYfeoabQM- Nate
DJI Digital FPV on a 3-inch Babytooth Drone! Cool! Mr ShutterBug 2021-01-21 | I call it my "Digitooth"! This 2S Babytooth has a stripped down Caddx Vista and it weighs just 59 grams + battery. It is my lightest and quietest drone with the DJI Digital FPV system. It's super fun! Build info below (click "Show More")...You can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugWant to help support this channel? Simply bookmark any of these links and use them when you shop for FPV gear. Each time you make a purchase, they will give me a small commission. It is totally free for you and it helps me get parts for future projects. Thanks! Banggood: http://bit.ly/2OVcf1r BETAFPV: http://bit.ly/betafpv-shutterbug GetFPV: http://bit.ly/2Ot4q2K Heli-Nation: http://bit.ly/heli-nationParts for this build:- Babytooth Frame 2mm thickness: http://bit.ly/3bZ92tC- FPVCycle Light 13mm 7700KV motor with 2mm shaft: http://bit.ly/2XWcOvQ- Gemfan 3018 2-blade prop with 2mm shaft: http://bit.ly/2t3Ee6Y (affiliate link)- Caddx Nebula Nano + Vista Air Unit: http://bit.ly/3ccH0cq (affiliate link)- Pick your favorite AIO FC. I did it the hard way with a BetaFPV 12A 2-4S whoop-style FC (USB pointing down), but I suggest you use a toothpick-style FC (USB to the side) for a much easier build: http://bit.ly/39NRnTf (affiliate link)- Crossfire Nano Receiver: http://bit.ly/3aJgC7O (affiliate link)- MiniMortal T V2 Crossfire Antenna: http://bit.ly/3o4gPIY- TrueRC Singularity U.FL LHCP Antenna: http://bit.ly/39SMbxg- TWIG Canopy: http://bit.ly/394Uhna- Flywoo Micro Arm LEDs: http://bit.ly/3qMF6Fz- M2x4 titanium motors screws: bit.ly/3kJ8FV8- Velcro cable ties, cut lengthwise to create two thin battery straps: amzn.to/2XCJVWN (affiliate link)- Cloth Tape: amzn.to/2GUm5PD (affiliate link)- I did not add a capacitorBatteries:- Tattu R-Line 95C 550mAh 2S: bit.ly/3p3BoHa (more info about the manufacturer here: bit.ly/3ilHXSR)- RDQ 80C 525mAh 2S: http://bit.ly/2Y1Ft2GTune:Full ESC and Betaflight settings here: http://bit.ly/3cxhpgzRelated Videos:- "Building the World’s Lightest 3-inch FPV Drone" youtu.be/obns6k1xhIc- "Taking it to the next level" youtu.be/bUUcPVNV2AA- "Can this 1S Toothpick Really Carry an Insta360 GO?" youtu.be/xP6_M2EYi1EMusic: "Heaven’s Path" by Roman Senyk Musicyoutu.be/ySKJcr7lCDk
I would love for you to WIN one of these three drones! Mr ShutterBug 2021-01-15 | That's right! I've decided to start giving more stuff away, starting with these three drones! All I ask is that you pay the shipping. Full rules below...How to enter:- Leave exactly one comment on this video.- In that comment, indicate which drone would you prefer to win? Please list a 1st, 2nd, and 3rd choice. I can't promise you will get your 1st choice, even if you win, but I will do what I can.Rules:- If you leave more than one comment you will be disqualified.- If I think you're trying to cheat in any way then you will be disqualified at my sole discretion.- Winners will be selected at random on Friday, January 22nd.- If you are selected, then I will try to contact you using the email address listed on the "about" section of your YouTube channel. If you do not have an email listed then I will respond to your comment on this video. So keep an eye on those YouTube notifications!- If I fail to hear from you within 48 hours then you will forfeit your prize and I will select another random winner. I don't want this to drag on too long.- Once you give me your mailing address, I will give you the exact shipping cost. At that time, you will pay for the shipping via PayPal. You can pay with any credit card (you don't need a PayPal account).- Once I receive the payment I will ship the package to you as soon as I can.- If you are selected as a winner but refuse to pay shipping, then you will forfeit your prize and I will select another random winner.- All prizes are given AS IS. If the prize is damaged in shipment or fails for some other reason, that would be unfortunate, but I will not be held responsible.Prizes:#1 - iFlight X2 Stretch with carbon frame, 1105 6000KV motors, 2.5" props, 20x20mm stack, 20A 2-4S ESC, Runcam Micro Sparrow 2 camera, FrSky XM+ receiver.#2 - Beta85X HD with 1105 5000KV motors, 2" props, Caddx Turtle V2 camera with 1080p DVR, FrSky XM+#3 - Beta75X 3S version, new in box, 1103 8000kv motors, 40mm props, 12A AIO, FrSky XM+Receiver Version:If you don't need the FrSky receiver, just let me know. I'll take it out and you can add whatever receiver type you use.Questions:If you have questions, feel free to add them to your comment on this video. If you want to ask a question but you do not wish to enter the contest, then please just make that clear in your comment.Good luck!- Nate
DAS Might Change The Way I Race Whoops! Emuflight’s New Dual-Axis Steering! Mr ShutterBug 2021-01-04 | I have a fresh new whoop for 2021 racing. It has updated components and a new tune, but the real secret sauce is a new feature of Emuflight called "Dual-Axis Steering". It's specifically designed for angle mode racing, and it may just change the way I fly whoops! Build info and tune below...Emuflight Tune:Thanks to Patrick Clarke for early access to this Project Mockingbird tune (still a work-in-progress). Emuflight screenshots and CLI commands can be found in this document: bit.ly/2MkaJajDual-Axis Steering:DAS is set up in the CLI. The names of the commands have changed since the time I made my video. If you’re using an older build the commands are called “add_yaw_to_roll” and “add_roll_to_yaw” (as described in my video). If you are using a newer build then they have been renamed to “das_roll_with_yaw_input” and “das_yaw_with_roll_input” respectively. The setting “das_yaw_with_roll_input” means, “when you tilt the roll stick, also make the drone rotate about the yaw axis.” This feature can be set differently for different rate profiles. The recommended starting values are given below. Increase the “das_yaw_with_roll_input” value if you want to do more of the steering on the right stick. Full right-stick-only steering is hard to get used to, but I enjoy using a mix in the middle.set das_yaw_with_roll_input = 30set das_roll_with_yaw_input = 20Drone Parts (If you use my affiliate links it helps me out. Thanks):- Meteor65 frame (http://bit.ly/3bxloXt)- BetaFPV F4 1S AIO FC + VTX (bit.ly/360DJtO)- HappyModel EX0802 19,000KV unibell motors (http://bit.ly/3859ZhL)- TinyWhoop Pinch camera (http://bit.ly/3pKhbGg)- Gemfan 31mm 3-blade props with 1mm shaft (http://bit.ly/2HfPnFt)- TPU camera mount (I think this is the one): http://bit.ly/2MvEYLJ- PEEK M1.4 4mm motor screws (bit.ly/3n4ntP6) are unfortunately very expensive. I didn't realize just how expensive they were at first because they sent me some free samples. Normally I use RENY screws (http://bit.ly/2P0JOzT) which are half the cost and even that is pretty expensive unless you split it with friends. Minimum quantity = 100 pcs.- 90 degree PH2.0, folded to create a 180 degree battery connector (http://bit.ly/2Jcu4Gj)Race Gates:- TinyWhoop Cube Gate: http://bit.ly/2KUcnPQ- BetaFPV Mini Flag Pole: http://bit.ly/35bASil60Hz flight footage recorded by ImmersionRC PowerPlay DVR:- GetFPV: http://bit.ly/power-play-dvr- Banggood: http://bit.ly/2NuJ7gtMusic:"Time is Up" by Roman Senyk Musicyoutu.be/6njGFTadInQHappy new year everyone!- Nate
1S Babytooth Drone vs. Insane Forest Canopy! Mr ShutterBug 2020-12-30 | Check out this spot! Gaps everywhere! I'm going to loose it flying like this, but it's too much fun! No holding back! Build info below...Build Info:This drone is almost identical to the one I showed in this detailed build video: youtu.be/obns6k1xhIc. This one is the same except it has Flywoo motors (because the fpvcycle motors were sold out at the time).60Hz FPV footage recorded using the Immersion RC PowerPlay DVR:- GetFPV: http://bit.ly/power-play-dvr- Banggood: http://bit.ly/2NuJ7gtMusic:"Heroic Feet" by Roman Senyk Musicyoutu.be/hvv8VLOKnsIThanks for watching! Happy New Year everyone!- Nate
This 1S Babytooth Still RIPS! Loven it! Mr ShutterBug 2020-12-18 | When I head out to fly for fun, what drone do I take this me? More often then not it's this 1S Babytooth. It's so much fun and so care free! Nobody can see it. Nobody can hear it. And if I crash, nobody even cares. It's like a leaf! I love it! Build info below...The Build:This is a 1S drone built on the Babytooth frame by Kabab FPV. I like to build mine extra light. This one is around 33 grams and flies on a 450-520mah 1S battery. For full build details, check out this video: youtu.be/obns6k1xhIcOr check out what happens when you strap an Insta360 GO on top!youtu.be/xP6_M2EYi1EMusic: Cinematic Inspiration by RomanSenykMusicyoutu.be/8qPqS-FSVGc
Will this FPV Drone Survive the Water? Mr ShutterBug 2020-12-05 | Can you really waterproof an FPV drone? If so, can it operate under the water? Let's find out! Build info and links below...Note:I post affiliate links when available. If you one of the links to make a purchase, then I can earn a small commission. It's an easy way for you to help support this channel at no cost to yourself. Thanks!If you're looking for a drone like my "ShutterBug85", then you can build one or buy the RTF drone from BetaFPV. They call it the Beta85 Pro 2 (yes I gave them permission to use my formula, but not my name). - From BetaFPV: http://bit.ly/2YukEPS- From GetFPV: bit.ly/3mKmPXADrone Parts:- Beta85X Frame: bit.ly/3bEvQgj- BetaFPV 1103 11000KV Motors (or similar): bit.ly/2IgFETq- BetaFPV 2-4S 12A AIO FC (but any 2s. capable AIO will work. I usually use the lighter 2s-only FCs): bit.ly/2JFqyay- Emax AVAN 2" props: http://bit.ly/30SYraU- Camera, VTX, & canopy like these (or substitute your favorite whoop FPV solution): bit.ly/39JTQiU- Velcro battery straps: amzn.to/2QxyMAL- U.FL extension cables cut down to make custom antennas: amzn.to/2UoTOFgChemicals Used:- Silicone Modified Conformal Coating (WARNING: TOXIC): amzn.to/35HZ3nd- Clear Silicone Sealant: amzn.to/2VHO3lG- Dry Drone (used on USB): bit.ly/3lMSs1j- Bondic UV Activated Glue (used on camera lens barrel): amzn.to/3qwoWkjMy Related Videos:- My original "AquaWhoop": youtu.be/4IsjStkv6vM- My original ShutterBug85 video: youtu.be/4uhbz7J9rH0- My review of the Beta85 Pro 2: youtu.be/sq9TCmiP4Dw- Securing props with Floss: youtu.be/DJdi-Lvu6xEMucis:- "Rock Upbeat" by RomanSenykMusic (youtu.be/r5VeAUoAkM0)- "Cruise (Sting)" by John Deley (YouTube Audio Library)
Whoopn with Wild Turkeys in Digital HD Mr ShutterBug 2020-11-26 | Exploring the forrest with digital FPV is pretty fun! This is an 85mm whoop with the a Naked Vista air unit. Build details below...Note:I post affiliate links when available. If you one of the links to make a purchase, then I can earn a small commission. It's an easy way for you to help support this channel at no cost to yourself. Thanks!Drone Info:The drone in this video is just like the Beta85X Digital VTX drone (bit.ly/beta85x_dji_digital_vtx) except on this occasion I was using 1105 5000kv motors (http://bit.ly/2uTUGYk) with a 450mah 3S battery. If you want this drone, or any BETAFPV parts, then use my code (Nate25Beta) for 25% off. You could also use the code to get a Caddx Vista (http://bit.ly/3aZv78u) and build whatever you want. Hope that helps. Happy flying! Music:"Anthem of Inspiration" by Roman Senyk Musicyoutu.be/cIcgpKvh-r4Warm Regards,- Nate
The Worlds Lightest 75mm Whoop is AMAZING! Mr ShutterBug 2020-10-31 | What happens to the performance of a 1S whoop when you make it HALF the weight of a typical BNF? Let me show you! It's pretty amazing! Links and custom tune below...You can also follow me on Instagram to see what I'm up to. I post pretty often these day:instagram.com/mrshutterbugWant to help support this channel? Simply bookmark any of these links and use them when you shop for FPV gear. Each time you make a purchase, they will give me a small commission. It is totally free for you and it helps me get parts for future projects. Thanks! Banggood: http://bit.ly/2OVcf1r BETAFPV: http://bit.ly/betafpv-shutterbug GetFPV: http://bit.ly/2Ot4q2K Heli-Nation: http://bit.ly/heli-nationThe Easy Way to Build (but not as light):If you want an easy build, just get a Meteor65 or Mobula6 and swap the parts onto a 75mm frame with 40mm props. Try 19,000KV or 19,500KV combined with my custom tune. It will be good, but not as good as my 16.8g version. For that, you'll have to build it up from components (see below): - Meteor65 BNF (from BetaFPV: http://bit.ly/2KvavJT, from GetFPV: http://bit.ly/2QtWpvZ)- Mobula6 (bit.ly/3mInNTI, or http://bit.ly/2wGRtw7)Full Parts List (as seen in this video):- Mobula7 V2 Frame (bit.ly/3eg3MRr, or bit.ly/3kGqm8m)- Happymodel EX0802 19,000KV Motors (bit.ly/366Jnej, or bit.ly/2TIDAFH) WARNING: The EX0802 motor wires are just barely long enough. Do not cut them shorter! You will need every mm of wire. I suggest pulling them out of the connector and then cutting off the crimped part, preserving as much of the wire length as possible.- BetaFPV F4 1S FC (the one I used) (bit.ly/3mLDHwZ, or http://bit.ly/2m2JX9e)- Alternative FC: BetaFPV F4 1S FC with built in VTX (bit.ly/360DJtO)- Alternative FC: CrazyBee F4 Lite 1S FC with built in VTX (bit.ly/34JB8oG, http://bit.ly/2H3XJjq)- HQ 1.6x1.6x4 Props w/ 1mm shaft (bit.ly/3mGOqbP, or bit.ly/2TD6Rln)- Runcam Nano3 Camera (http://bit.ly/39w6QFK)- NamelessRC Nano VTX (bit.ly/30VLksU)- E6000 Glue (amzn.to/358DX3m)- U.FL extensions cut to make custom VTX antenna (amzn.to/2UoTOFg)- RENY M1.4 4mm motor screws (http://bit.ly/2P0JOzT)ESC Setup:- Flash JESC v2.3 with 48kHZ PWM- Startup Power = 1.0- Demag Compensation = High- Motor Timing = Medium High- Enable Bi-directional DSHOT (small fee for H-type ESCs, free for L-type)Betaflight 4.2.3 CLI Diff:feature -AIRMODEset gyro_lowpass2_hz = 375set dyn_notch_width_percent = 0set dyn_notch_q = 250set dyn_notch_min_hz = 125set dyn_notch_max_hz = 350set dyn_lpf_gyro_min_hz = 300set dyn_lpf_gyro_max_hz = 750set rc_smoothing_auto_smoothness = 7set fpv_mix_degrees = 13set dshot_idle_value = 700set dshot_bidir = ONset motor_pwm_protocol = DSHOT150set motor_poles = 12set thr_corr_value = 3set thr_corr_angle = 650set vbat_max_cell_voltage = 440set vbat_min_cell_voltage = 300set vbat_warning_cell_voltage = 310set yaw_motors_reversed = ONset small_angle = 180set pid_process_denom = 4profile 0set dyn_lpf_dterm_min_hz = 105set dyn_lpf_dterm_max_hz = 255set dyn_lpf_dterm_curve_expo = 7set dterm_lowpass2_hz = 225set iterm_relax_cutoff = 20set yaw_lowpass_hz = 100set throttle_boost = 7set throttle_boost_cutoff = 25set p_pitch = 69set d_pitch = 68set f_pitch = 133set p_roll = 63set d_roll = 62set f_roll = 126set p_yaw = 68set f_yaw = 126set angle_level_strength = 90set level_limit = 65set d_min_roll = 0set d_min_pitch = 0set ff_spike_limit = 70set ff_smooth_factor = 20rateprofile 0set roll_rc_rate = 210set pitch_rc_rate = 210set yaw_rc_rate = 220set roll_expo = 40set pitch_expo = 40set yaw_expo = 40set roll_srate = 0set pitch_srate = 0set yaw_srate = 0More videos you might like:- My Lightest 65mm Whoop: youtu.be/Rz0MjU4Gg3A- My Lightest 3-inch Toothpick: youtu.be/obns6k1xhIc- My 0802 Whoop back in 2018: youtu.be/LNMUu0T9_Nc- My Meteor65 Review: youtu.be/syrTruX5xJg- My Mobula6 Review: youtu.be/XkIKaanPBao- Whooptopia 2020 (epic whoop racing!): youtu.be/dN_4suzyWTcMusic:"Whiskey" by Huma-Huma (YouTube Audio Library)Thanks for watching! Share the video link with your friends if you think they'd enjoy it too. :-)Warm regards,- Nate
How does it all fit? New F722 35A 6S AIO with DJI PNP Connector. Mr ShutterBug 2020-10-22 | This is the new BETAFPV 35A 6S AIO that I used in my recent ET5 build. I've been rip'n it pretty hard on 6S! So far so good! Click "SHOW MORE" for links and details...Full specs on the official product page:http://bit.ly/betafpv-f722-35a-6s-aio (affiliate link)Want to see some crazy flight footage with this FC running 8K/8K/DSHOT600 with RPM Filtering?youtu.be/5sJYGE7f6GUI've crashed pretty hard several times and I've used turtle mode to get out of trees. No issues yet, but only time will tell if it turns out to be really reliable for everyone. Fingers crossed!Thanks for watching! Take care everyone!- Nate
Can this 1S Toothpick Really Carry an Insta360 GO?!?! Mr ShutterBug 2020-09-28 | Can this 1S Toothpick carry the Insta360 GO and if it can, will it have enough performance headroom to get some cool shots? I had to find out! Build info below...Note:I post affiliate links when available. If you one of the links to make a purchase, then I can earn a small commission. It's an easy way for you to help support this channel at no cost to yourself. Thanks!Build Info:This is a 1S drone built on the Babytooth frame by FPV Cycle. The drone weighs about 33g and is very similar to the first one I built, which I showed in my video "Building the Worlds Lightest 3-Inch FPV Drone": youtu.be/obns6k1xhIc. The battery weighs 13g and the Insta360 GO weighs 20g, so battery + action cam doubles the weight of the drone for a flying weight of 66g.Insta360 GO:Tiny action cam with amazing image stabilization. It can only record for 5 minutes at a time and will run out of battery after two flights, but it opens up some interesting possibilities, so I have fun with it. From GetFPV: bit.ly/32fxulvFrom BetaFPV: bit.ly/3id5vbGMusic:"Keys of Moon - The Epic Hero" is under a Creative Commons license (CC BY-SA 3.0) https://creativecommons.org/licenses/...Music promoted by BreakingCopyright: youtu.be/ETbsXdqgcTM
THIS NEW ULTRALIGHT 5-INCH RIPPER IS AWESOME (TWIG ET5 2004 1700KV 6S) Mr ShutterBug 2020-09-24 | I have experimented with other ultralight 5-inch drones in the past, but this one is AWESOME! It's tough, it's quiet, and it really RIPS! I love it! Click "SHOW MORE" for full parts list...Note:I post affiliate links when available. If you one of the links to make a purchase, then I can earn a small commission. It's an easy way for you to help support this channel at no cost to yourself. Thanks!Related Videos:- My First Ultralight 5-INCH Experiment: youtu.be/qMj-RM7XBfU- My Review of the TWIG ET5 BNF: youtu.be/EHn5RcFMZzc- My Review of the X-Knight5 BNF: youtu.be/K0frof9ktgsAbout the FC:I couldn't show it at the time, but I was using the new BETAFPV 35A 6S AIO FC with F722 processor (http://bit.ly/betafpv-f722-35a-6s-aio). That's a lot faster than an F411 or F405. I was running 8K/8K/DSHOT600 with RPM filtering enabled. I later made a video about the FC. You can check it out here: youtu.be/lys4O53A1QUNote: I post affiliate links when available, so it helps me out if you choose to use them. :-)Full Parts List Below:- TWIG ET5 Frame Kit (BetaFPV: bit.ly/30RlUMu, or HeliNation: bit.ly/33Y83py)- BetaFPV 2004 1700KV T-Mount Motors (BetaFPV: bit.ly/betafpv-2004-motors, or GetFPV: bit.ly/3iYVUWm)- BetaFPV F722 AIO 35A 6S flight controller (http://bit.ly/betafpv-f722-35a-6s-aio)- Caddx Baby Ratel Camera with 1.8mm Lens (bit.ly/33TCUUt)- BetaFPV M02 350mW VTX (bit.ly/3djjgSM)- TBS Crossfire Nano Receiver with Immortal-T V2 Antenna (bit.ly/36c3FlV)- Titanium M2x6 screws for motors (bit.ly/2RPYguB)- Titanium M2x8 screws for props (bit.ly/2FKFenb)- Titanium M3x16 screws for canopy (can't find a link right now)- Other mounting hardware comes with the kit- Cloth tape for motor wires (amzn.to/2GUm5PD)- 200mm battery strap (15mm width)Batteries I Use (XT30 works, but XT60 is probably the right way to go):- BetaFPV 550mah 6S (bit.ly/2RSWpVM)- Tattu R-Line 650mah 6S (bit.ly/2z9GVqN)- GNB 750mah 6S (bit.ly/2ZfXXOx)Betaflight 4.1.4 Setup (for the BetaFPV F722 AIO with BLHeli32):set gyro_lowpass2_hz = 325set dyn_lpf_gyro_min_hz = 260set dyn_lpf_gyro_max_hz = 650set dshot_burst = ONset dshot_bidir = ONset motor_pwm_protocol = DSHOT600set yaw_motors_reversed = ONset small_angle = 180set pid_process_denom = 1profile 0set dyn_lpf_dterm_min_hz = 91set dyn_lpf_dterm_max_hz = 221set dterm_lowpass2_hz = 195set p_pitch = 41set i_pitch = 81set f_pitch = 86set p_roll = 38set i_roll = 77set f_roll = 81set p_yaw = 27set i_yaw = 81set f_yaw = 81rateprofile 0set roll_rc_rate = 210set pitch_rc_rate = 210set yaw_rc_rate = 210set roll_expo = 40set pitch_expo = 40set yaw_expo = 40set roll_srate = 0set pitch_srate = 0set yaw_srate = 0set tpa_rate = 70set tpa_breakpoint = 1200Music:ONLAP - Everywhere I Goopen.spotify.com/track/33W6nFqHIhVCfGLiafK3kryoutube.com/channel/UCDu5kwaUa5eokd1ugr8-IoAinstagram.com/onlap_musicsoundcloud.com/onlapmusictwitter.com/OnlapMusicfacebook.com/ONLAP.OfficialMusic provided by RFM: youtu.be/G0k2oYR0CjQ
NAKED AIR UNIT for a LIGHTER DJI WHOOP | Beta85X HD Digital VTX Mr ShutterBug 2020-09-20 | This 2-3S WHOOP has DJI Digital FPV and yet it is just 66g + battery. The secret to the relatively low weight is a modified Vista Air Unit with NO HEAT SINKS! Is that really OK? Let's talk about it! Click "SHOW MORE" for build specs and product links...Note:I use affiliate links when available. If you use the links to make a purchase, then I can earn a small commission. It's an easy way for you to help support this channel at no cost to yourself. Thanks!Bind-n-Fly Drones:Beta85X HD Digital VTX Drone: bit.ly/beta85x_dji_digital_vtxBeta75X HD Digital VTX Drone (even smaller & lighter): bit.ly/beta75x_dji_digital_vtxDJI Digital FPV Goggles: bit.ly/3kUyCSIFull Parts List:- Beta85X 4K Frame + Carbon Brace (bit.ly/3iNVtOi)- Caddx Nebula Nano + Vista Air Unit (bit.ly/3ccH0cq)- BetaFPV 1103 8000KV Motors (http://bit.ly/2YZctrM)- BetaFPV F4 12A AIO (http://bit.ly/2X6Tr1S)- EMAX Avan 2" Props (http://bit.ly/30SYraU)- Battery Straps (bit.ly/33IbHlY)- Whoop canopy for Nebula Camera (bit.ly/2H7gJk7)- Small LHCP Antenna (bit.ly/35Pc68M)- M1.6x6 screws will be needed if you want to use the 1103 motors and the carbon brace (amzn.to/3mAL4If)- 300mah 3S Battery (http://bit.ly/2kQl9Bj)- 450mah 3S Battery (http://bit.ly/2mPyRot)Music:Smooth Ridin by Huma-HumaThanks for watching!- Nate
Meteor65 HD Review + NEW BETAFPV 1S AIO FC with BUILT-IN VTX Mr ShutterBug 2020-09-13 | This is the Meteor65 HD. It's way lighter than the 65X HD because of a new AIO FC that has a built-in VTX (a first for BETAFPV). The reduced weight helps it to fit through some crazy small gaps! Click "SHOW MORE" for full specs and product links...Note:I post affiliate links when available. If you one of the links to make a purchase, then I can earn a small commission. It's an easy way for you to help support this channel at no cost to yourself. Thanks!Meteor65 HD 1S Drone: bit.ly/meteor65hdNew Betafpv F4 AIO 1S Brushless FC with built-in VTX: *not yet released by itself. Check here for updates: http://bit.ly/2ZuZ4XcRelated Videos on My Channel:- Beta65X HD Review: youtu.be/4ZmC1l-D15w- Replacing Battery Connectors the SAFE Way: youtu.be/nmwOxncToJM- Epic Whoop Racing | Whooptopia 2020: youtu.be/dN_4suzyWTcMeteor65 HD Specs:- Weight: Just under 28g (without battery)- FC: F4 AIO 1S Brushless FC w/ built-in VTX- Frame: Meteor65 frame- Motors: 0802SE 22000KV- Props: Gemfan 31mm 3-blades props 1.0mm shaft hole- Camera: Betafpv Nano HD Camera- Canopy: Canopy for Nano HD Camera- Camera Tilt: 30 deg (not adjustable)- Receiver Option: Frsky FCC/ Frsky LBT/ Futaba- Batteries: BT2.0 300mah or 333mahBatteries for this drone:- BetaFPV 300mah 1S with BT2.0: http://bit.ly/2OnpqXu- TinyWhoop 333mAh 1S with BT2.0 (BEST): http://bit.ly/2PQvGJQNew Betafpv AIO 1S FC Specs:- Weight: 5.33g with power lead & antenna- CPU: F411- ESCs: 5A- Built-in SPI Receiver: Frsky FCC/ Frsky LBT/ Futaba- Built-in VTX with SA: 25mW- Programable RGB LEDs: 2 on the bottom- Power Lead: 22AWG BT2.0- Antenna: Linear dipole with U.FL connectorWhat do you think? Comment down below and let's talk!Warm Regards:- Nate
X-Knight 5 Review (watch this before you fly it) Mr ShutterBug 2020-09-06 | This 5-inch 6S drone is so light you don't even have to register it with the FAA, but is it worth it for you? I've packed a ton of info into this video so hopefully it can help answer that question. Click "SHOW MORE" for links and build suggestions:Note:I post affiliate links when available. If you one of the links to make a purchase, then I can earn a small commission. It's an easy way for you to help support this channel at no cost to yourself. Thanks!Related Videos:- TWIG ET5 Review: youtu.be/EHn5RcFMZzcX-Knight 5 (Analog FPV Version, as seen in this video):- From BetaFPV: bit.ly/31ZIbsb- From GetFPV: bit.ly/2FcPxzKX-Knight 5 (DJI Digital FPV Version):- From BetaFPV: bit.ly/3hNfwfoIf you want to build an ultra-light 5-inch, then I suggest these parts:- TWIG ET5 frame kit with canopy: bit.ly/30RlUMu- Toothpick style 35A AIO FC (up to 6S): http://bit.ly/betafpv-35a-6s-aio-blhe...- Caddx Baby Ratel camera w/ mounting adapter: bit.ly/33TCUUt- Gemfan 5125 3-blade prop (bit.ly/34a6OUH)- BetaFPV 2004 1700KV Motors: bit.ly/betafpv-2004-motors- VTX and antenna of your choiceBatteries & Stuff:- BetaFPV 550mAh 75C 6S Battery: bit.ly/2zSDpBq- Tattu R-Line 650mAh 95C 6S Battery: bit.ly/2z9GVqN- E6000 Glue: amzn.to/358DX3m
TWIG Mutant + Digital FPV + Awesome New Flying Spot! Mr ShutterBug 2020-08-18 | Check out this awesome new FPV spot! Taking in the sights, and rip'n the gaps in real-time HD! Click "SHOW MORE" for full build info...DJI Digital FPV Goggles:- From GetFPV: bit.ly/3kUyCSIDJI Settings:- 50mbps Mode- Low Latency Mode (my preference)- 16x9 WidescreenParts List:- TWIG Mutant frame: http://bit.ly/3cQeVY5- TWIG Megabat Vista Canopy: phx-3d.com/racerx- BetaFPV F4 2-4S 20A AIO FC: http://bit.ly/betafpv-20a-aio-v3- BetaFPV 1505 3600KV Motors: http://bit.ly/betafpv-1505-3600kv-motors- Caddx Vista: http://bit.ly/3aZv78u- TBS Crossfire Nano Receiver: http://bit.ly/3aJgC7O- Gemfan 4024 2-Blade T-Mount Props: bit.ly/2ZFkQcX- Tattu R-Line 850mah 4S with XT30: http://bit.ly/2IRwJ7L- Titanium M3 bolts for canopy- Mine is about 170g dry weightWarm egards,Nate
TWIG ET5 | Ultralight 5 In Depth Review Mr ShutterBug 2020-08-14 | Lets talk about these new ultralight 5" drones! What does the ET5 bring to the table, how does the BNF version stack up, and what would I do to make it even better? Click "SHOW MORE" for my custom tune, build suggestions, and links...Bind-N-Fly Drone (as shown):- TWIG ET5 BNF: bit.ly/TWIG-ET5-BNF- BetaFPV 850mAh 75C 4S Battery: bit.ly/2AYvnriParts I would recommend:- TWIG ET5 frame kit with canopy: bit.ly/30RlUMu- Toothpick style 35A AIO FC (up to 6S): http://bit.ly/betafpv-35a-6s-aio-blheli32- Caddx Baby Ratel camera w/ mounting adapter: bit.ly/33TCUUt- Gemfan 5125 3-blade prop (bit.ly/34a6OUH)- OR: HQ 5x3 2-blade prop (bit.ly/2DPPyJr)- VTX and antenna of your choice- Motors (see below)Some motor options to consider:- BetaFPV/RacerX 1506 3000KV (shown here): bit.ly/315Rs1V NOTE: These are great motors but a little small for 5-inch.- BetaFPV 1805 (pick your KV): bit.ly/betafpv-1805-motors NOTE: These are better motors for 5" but may be less durable.- BrotherHobby 2004 (pick your KV): bit.ly/2PPfjMl NOTE: I have not tried these, but they look like a great size for an ultralight 5". If you have experience with them, please comment below. :-)My BLHeli32 Settings:- Rampup Power = 100%- Motor Timing = 22 deg- PWM Frequency = 24kHzMy Betaflight 4.2.0 Tune:- bit.ly/3fQWXVHIf you have questions, suggestions, or tuning tips for me then I would love to talk in the comments section. I'm learning every day along with all of you!Warm Regards,- Nate
Air Cannon Drone Rescue? Mr ShutterBug 2020-08-06 | Check out this air cannon my friend Clif built! We used it to search for my 3" 1S drone. Details below...Build video for the drone (SO GOOD!): youtu.be/obns6k1xhIcArborists Throw Weight & Line Kit: amzn.to/3kh9up0Foldable Storage Cube for Throw Line : amzn.to/31m7fbq
