Uploaded September 2018 | Updated November 2026, 6 hours ago
There are a hand full of tests for platinum. One is, for example, the precipitation as Ammonium hexachloroplatinate(VI). This reaction has some advantages. As the product precipitates in a huge volume trace amounts can be detected. Although we tried this often before we were never able to make this complex so it doesn't seem to be of many advantages here. Also, you'd still have to distinguish between Pd and Pt which are quite similar in their chemistry.
This is why we tried the SnCl2 test. In addition to the original description, we added the SnCl2 under acidic conditions, so directly to the diluted Aqua Regia. Many tests of platinum group metals require the addition of ammonia first. But we only have 9% Ammonia which means, you would have to add a large volume and therefore dilute the weak solutions even further.
On the left, you can see a freshly prepared H2PtCl6 solution, from boiling Pt in Aqua Regia for 30 minutes under reflux. A few drops from the concentrated, red solution were taken and diluted by adding water. For the Pd, we used some of the K2PdCl6 we had prepared a while ago and added it to boiling Aqua Regia (to have the same setup in both vials). It was diluted as well until the colors eventually matched.
To both of them, SnCl2 was added. The one with Pt shows a yellow to red color while the one with Pd shows a brown color that quickly precipitates a dark layer.
With Gold, it is supposed to form a dark to purple layer of fine gold particles making it a good test for precious metals.
What exactly happens here is still somewhat of a mystery to us. Judging from the redox-potentials it seems likely that under these acidic conditions the Pt and Pd will be reduced to the metals forming nanoparticles that show different colors. But there are also reports on an H2PtCl6/SnCl2 system in catalysis where even under protic conditions Pt-Sn complexes with metal-metal bonds are observed. We don't know however how this adds up to the excess of SnCl2 and the increased redox-potentials due to acidity. So we won't try to give an answer for why the two metals show different colors for now.
There are a hand full of tests for platinum. One is, for example, the precipitation as Ammonium hexachloroplatinate(VI). This reaction has some advantages. As the product precipitates in a huge volume trace amounts can be detected. Although we tried this often before we were never able to make this complex so it doesn't seem to be of many advantages here. Also, you'd still have to distinguish between Pd and Pt which are quite similar in their chemistry.
This is why we tried the SnCl2 test. In addition to the original description, we added the SnCl2 under acidic conditions, so directly to the diluted Aqua Regia. Many tests of platinum group metals require the addition of ammonia first. But we only have 9% Ammonia which means, you would have to add a large volume and therefore dilute the weak solutions even further.
On the left, you can see a freshly prepared H2PtCl6 solution, from boiling Pt in Aqua Regia for 30 minutes under reflux. A few drops from the concentrated, red solution were taken and diluted by adding water. For the Pd, we used some of the K2PdCl6 we had prepared a while ago and added it to boiling Aqua Regia (to have the same setup in both vials). It was diluted as well until the colors eventually matched.
To both of them, SnCl2 was added. The one with Pt shows a yellow to red color while the one with Pd shows a brown color that quickly precipitates a dark layer.
With Gold, it is supposed to form a dark to purple layer of fine gold particles making it a good test for precious metals.
What exactly happens here is still somewhat of a mystery to us. Judging from the redox-potentials it seems likely that under these acidic conditions the Pt and Pd will be reduced to the metals forming nanoparticles that show different colors. But there are also reports on an H2PtCl6/SnCl2 system in catalysis where even under protic conditions Pt-Sn complexes with metal-metal bonds are observed. We don't know however how this adds up to the excess of SnCl2 and the increased redox-potentials due to acidity. So we won't try to give an answer for why the two metals show different colors for now.


![Thallium Chemistry: Ferrocyanide and Chromate in comparison
A yellow (hard to see on camera) Potassium Ferrocyanide solution (left) and a very dilute yellow Potassium Chromate solution (right) are prepared. Some drops of a Thallium(I) Nitrate solution are added to both of them.
Although both compounds are yellow for Potassium and the other Alkali metals (Thallium(I) can under certain circumstances be treated as an alkali metal-ion) the Ferrocyanide one is white.
We discovered this effect when we tried to prepare a bunch of Thallium compounds. It appears that many Ferrocyanides especially with d-Metals as counterions show completely different colors.
We are still not sure how exactly the counterion takes part in the coloration of complexes and will discuss this in a further video on Ferrocyanides. One idea is, as we visualized some structure data for Tl4[Fe(CN)6] that the Tl has trigonal prismatic and octahedral coordination (N-coordinated by the Cyanides backside).
So this has either to do with the Lewis-Acidity (electrophilic) of the counterion, pulling some of the ligands electron density away from the coordinated metal (Fe) thereby lowering the ligand field splitting and causing a red-shift.
Or for d-Metals as counterions (we checked their crystal structure as well) there are octahedra (N-coordinated) around the counterions as well. So we might have a second ligand field splitting here causing a mix of two colors.
We will try to find out more about the actual mechanism of this (hopefully) soon.
Still we found this effect quite interesting, as Thallium compounds usually are not colored (much like Alkali Metals or Silver) and the color here comes from the Chromate and Ferrocyanide that the products although the complex part has the same color end up in different colors. Thallium Chemistry: Ferrocyanide and Chromate in comparison](https://i.ytimg.com/vi/jQVU1c7zH34/mqdefault.jpg)
![Mercury Chemistry: Co[Hg(SCN)4]
In this video, we make an interesting compound Co[Hg(SCN)4]. It is prepared by mixing a Hg solution with NH4SCN and adding some CoCl2. The compound does not form right away but after a while, tiny blue parts can be seen all over the solution. They quickly fall to the bottom where after a night bigger flakes had formed as well.
As you can the solution is clear in the end, so all the CoCl2 has reacted to form the insoluble Co[Hg(SCN)4]. As they grow so slowly often bigger crystals can be made.
Now you might say this could also be Co(SCN)x. True, they have a similar color. But we made the Thiocyanatocobaltate(II) about 2-3 years ago and since then left it on the shelf and it never precipitated. While here we have a much lower conc. of Co(II). Hg(SCN)2, on the other hand, is not colored because Hg(II) is a d10-system. Mercury Chemistry: Co[Hg(SCN)4]](https://i.ytimg.com/vi/jUqjZziourY/mqdefault.jpg)
 [I3](-) forms. Thallium Chemistry: Thaliium(I)-Triiodide](https://i.ytimg.com/vi/jw5S6mtx338/mqdefault.jpg)
![Mercury Chemistry: Hg3[AsO3]2 and Hg3[AsO4]2
In this video, we make and compare a Mercury(II)-Arsenite and -Arsenate by mixing HgCl2 with NaAsO2 and NaHAsO4. Now usually we do not make every possible compound just to increase the number of videos but for this, we wanted to test something. The Arsenate is, according to literature yellow, while the Arsenite is colorless, but develops a yellow color which is believed to be due to oxidation. We wanted to test this and made both solutions.
At first, you cannot see any precipitate (right jar = Arsenate) but after a while, and a second addition of more Arsenate you can see a yellow turbid color. For the Arsenite, it happens much fast but the solution turns yellow as well, much as expected. If you compare the two after a while you can see that they have the same type of yellow in their solution. 24h later the Arsenate had precipitated as yellow compound while the Arsenite formed a colorless one.
This proves, that the compounds differ in color and only a small fraction, the parts in solution are yellow, probably due to oxygen in the water and the stirring process and that it probably is some oxidation of the Arsenite.
We also tested both up to 350°C for thermochromism but nothing happened. Mercury Chemistry: Hg3[AsO3]2 and Hg3[AsO4]2](https://i.ytimg.com/vi/kCN6V7e5-Eo/mqdefault.jpg)

 and [CoCl4](2-) you probably thought this could be possible with similar compounds as well.
So what we did here was to mix CuCl2 with H2O and HCl to a ratio where the nearly colorless, blue [Cu(H2O)6](2+) is turned into the green [CuCl4](2-) when it is heated. Copper Chemistry: Copper Thermochromism](https://i.ytimg.com/vi/l6AYp2X_iq4/mqdefault.jpg)

. So why is it stable in aqueous conditions ?
Lets assume we had Copper(I) in a gas phase, free from any solvation- or hydration energy. To make Cu(II) we require a lot of Ionizationenergy. This makes the reaction really endothermic. If we take it and dissolve it into Acetonitrile, lets say CuCl which is soluble in Acetonitrile, it will dissolve and stay as Cu(I). The reason for this is that the solvationenergy in Acetonitrile is too low to overcome this ionization energy. Water however produces a quite large Energy and Cu(II) can be formed under disproportionation.
Now what happens in this experiment ?
2 Cu(I) to Cu(II) and Cu(0) is an equilibrium. In water it is exothermic forming Cu(II). And if you work with Cu(II) solutions it wont turn into Cu(I) (unless you add an reducing agent like Sulfite) as no Cu(0) is present to shift the equilibrium back. As we know from Le Chatelier, if a reaction is exothermic, heat causes the system to go back to the endothermic side. So Cu(I) forms and combines with the Cl(-) which is present to form CuCl. CuCl is insoluble in water as the lattice energy is higher than the hydration energy and thus Cu(I) remains stable discoloring the blue solution over time. Copper Chemistry: Synproportionation Cu(II) and Cu(0)](https://i.ytimg.com/vi/mGx4hOx7YdY/mqdefault.jpg)
