Uploaded February 2019 | Updated September 2026, 2 weeks ago
Hy There,
In this video i will make my logo in 3d technique.
First i draw a better resolution logo in photoshop, than draw it in 3D using solidworks so i can 3D print the logo, than i show postprocessing, all the way to the painting on different method, from applying putty, airbrushing, to injection painting and finaly protecting it with lacquer
In this project wasn't go everything by the plans but still got some nice logos on the end.
Thanks for watching.
Hope you enjoy in video and welcome to watch my other channel:
Tine Sedej:
youtube.com/channel/UCNwj7T3yDfUbmARRHERF8QA
Foto, video & editing: Tine Sedej
Camera:
Sony A6500 [sel 18-200 f3,5-5,6]
Sony A6000 [sel 30 f3.5macro]
GoPro 7 Black
Music is from: youtube audio library
Nimbus - Eveningland
Hy There,
In this video i will make my logo in 3d technique.
First i draw a better resolution logo in photoshop, than draw it in 3D using solidworks so i can 3D print the logo, than i show postprocessing, all the way to the painting on different method, from applying putty, airbrushing, to injection painting and finaly protecting it with lacquer
In this project wasn't go everything by the plans but still got some nice logos on the end.
Thanks for watching.
Hope you enjoy in video and welcome to watch my other channel:
Tine Sedej:
youtube.com/channel/UCNwj7T3yDfUbmARRHERF8QA
Foto, video & editing: Tine Sedej
Camera:
Sony A6500 [sel 18-200 f3,5-5,6]
Sony A6000 [sel 30 f3.5macro]
GoPro 7 Black
Music is from: youtube audio library
Nimbus - Eveningland
![Another way How to drill a hole through a round bar in perfect center [middle]](https://i.ytimg.com/vi/eUTWtHOVyPI/mqdefault.jpg "Another way How to drill a hole through a round bar in perfect center [middle]
Another way to drill the hole in perfect center through the round shape bar.
I use 12mm brass bar just to show you the process. this method is good if you heave to drill more same parts, just use harder material for lead.
music:
Runaways, Silent Partner from youtube audio library")
![Ortur Laser Master 2 Pro - LU 2-4 [unbox / review / first test] + air assist stl files](https://i.ytimg.com/vi/eu4Wx7DSpr0/mqdefault.jpg "Ortur Laser Master 2 Pro - LU 2-4 [unbox / review / first test] + air assist stl files
Hy There,
in this video i will try my new ORTUR laser master 2 PRO
i think it is very good laser machine with strong and ridgit frame, many protections,
but with some software / firmware problems but when you deal with that software and prepare machine to work it become a great powerfull laser engraver / cutter
Here you can buy on ortur store:
Ortur laser master 2 PRO S2 version:
https://s.zbanx.com/r/j9xAq49kgmNy
Ortur Z-Height Adjuster for Laser Module Height Adjustment
https://s.zbanx.com/r/okp6k2nQeluE
Ortur YRR 2.0 Rotary Roller for Cylinder Engraving
https://s.zbanx.com/r/JYHwOcCIYfeu
Ortur Metal Enclosure for Laser Master 2 Pro
https://s.zbanx.com/r/jJKg9ebMCZ2c
But honestly got better price in banggood where is 2s model in preorder for lower price
https://www.banggood.com/custlink/vKmdN8lv8F
(this is my affiliate links, if you buy from that links you get cheaper, and I get a piece of cake)
Manual:
https://ortur.tech/documentation/olm2pro/OLM2_Pro_User_Manual_EN.pdf
Drivers: (drivers tab)
https://ortur.tech/olm2pro/
How to make it work on windows 7
https://ortur.tech/documentation/olm2pro/OLM2%20Pro%20-%20DRIVER%20WINDOWS%207.pdf
Firmware (download and read manual first)
https://ortur.tech/latest-firmware/#olm2pro
Materials Reference
https://ortur.net/pages/materials-reference
Stl files could find here:
https://www.thingiverse.com/thing:5212190
English language was always pain in the a** for me, I respect every correction, but please be gentle
Thanks for watching.
if you want to support me for more projects like this, my paypal is:
https://www.paypal.me/TinC33
Hope you enjoy in video and welcome to watch my other channel:
Tine Sedej:
https://www.youtube.com/channel/UCNwj...
Foto, video & editing: Tine Sedej
Camera:
Sony A6500 [sel 18-200 f3,5-5,6 Zeiss touit 50 2.8 macro]
Sony A6000 [sel 30 f3.5macro Sigma 30 1.4]
GoPro 7 Black
Music is from epidemic sound:
1: ES_Amigo (Instrumental Version) - Nico Rengifo
2: ES_Amanecer - El Neon
3: ES_Topo - El Neon
4: ES_Hola (Instrumental Version) - Nico Rengifo
5: ES_Dale! - Timothy Infinite
6: ES_Desamor (Instrumental Version) - Lawd Ito
7: ES_Ardor - Cushy")
![Air eraser, mini sand blaster P8N7, unboxing / review [part1]](https://i.ytimg.com/vi/fnK17v7Wbzs/mqdefault.jpg "Air eraser, mini sand blaster P8N7, unboxing / review [part1]
Review of Sandblasting Airbrush Sandblaster Spray Model Air Brush Kit 0.5mm Spray Gun P8N7
US $23.53 on ebay
Descriptions:
This professional air eraser is widely used for metal etching, glass engraving/hand-cut, model making, cake decorating, tattoos, nail art, etc. Its connected with the pump, whose spraying materials is emery, spraying on surface of metal or glass. Can be used for metal surface etching, glass surface hand-cut, and so on. Perfect for artwork, nail art beauty, body art, design painting, model painting, cake decoration, craft, models and fine art such as car painting illustration, textile and t-shirt painting.
Features:
Suitable for airbrush dia 0.5mm.
With elegant design and mini size.
Wide range of applications: metal etching, glass engraving/hand-cut, model making, cake decorations, draw the outline of camouflage，tattoos, nail art, etc.
Single action trigger design saves raw materials and durable.
Widely used by the general model enthusiasts.
Exquisite atomization effects and fine lines with this airbrush.
Specifications:
Brand: KKMOON
Color: Silver + Blue
Material: Aluminum + Copper + Plastic
Feed Type: Gravity Feed
Switching Mode: Single Action
Nozzle Diameter: 0.5mm / 0.019in
Fluid Cup Capacity: 15cc / 0.91cu in
AirHose: 1.8m / 5.9ft
WorkingPressure: 30-65psi
Item Size: Approx. 14 * 3 * 9cm / 5.8 * 1.1 * 3.3in
Item Weight: Approx. 96.8g / 3.4oz
Package Size: Approx. 24 * 18 * 4.3cm / 9.4 * 7.1 * 1.7in
Package Weight: Approx. 535.4g / 18.9oz
How to spray:
1.Fill fluid in the cup after thinning appropriately.
2.Hold the airbrush lightly in your hand
3.By pressing the main lever, a stream of air emerges. Then draw it backward gradually for color atomization.
4.The spray pattern is in accordance with the distance between a work surface and a air brush.
5.For fine line spray, remove the needle cover and hold the air brush near a work surface.
Maintenance:
1.Empty the fluid cup and wash with water or solvent by a brush.
2.Refillcup with water or solvent, then block the needle cover with a finger and spray.
3.The air flows backward into nozzle to clean the paints remained the airbrush.
Package List: E1651
1 * 0.5mm Airbrush
1 * Gauze Mask
1 * Emery
1 * Hook
1 * Air Hose
1 * User Manual
1 * Storage Case for Airbrush Kit
Skladba:
Smooth Sailing (with Guitar) izvajalca Audionautix je licencirana z licenco Creative Commons Attribution (https://creativecommons.org/licenses/by/4.0/)
Izvajalec: http://audionautix.com/")
![Winter time - RC Snow Plow with 17Kg Traxxas summit [hydraulic powered plow]](https://i.ytimg.com/vi/gm4Hr7pFyUk/mqdefault.jpg "Winter time - RC Snow Plow with 17Kg Traxxas summit [hydraulic powered plow]
Hy There,
Today, i just make a quick video about heaving fun in winter time with my traxxas summit and homemade hydraulic powered snow plow.
There is a bit low amount of snow, just about 5cm and we walk and drive over this snow so it was a bit hard and freezed under because theres freezing those days (about -10°C)
If i catch the fresh snow without someone drive over it, summit can push about 10-15cm of wet snow without problem.
I cahge tyres, with Pro-Line racing BIG JOE because, original one is far too soft for job like that(winter service :) )
Also the motor and controller is brushless which work perfect for a few years now, more about setup can see there:
https://www.youtube.com/watch?v=JkdnzhiVQkA
For normal driving i drive on 4s but for plowing i use only one 2s packet for power the summit and on other side one pack of 2s for powered hydraulic pump motor, also the summit is much slower with 2s.
For lifting the plow i use single channel from original transmitter, instead of 1st and 2nd gear switch i mount two buttons in it, so i got 3 pozition on one channel for controlling hydraulic, more about it you can see there:
https://www.youtube.com/watch?v=jLYJOSKB4QU
Servo for gear simply put in first gear posittion and disconnect them, than connect hydraulic servo on its place.
I also try with chains on tyres but got worst result, grip was just so bad.
Snow plow size is 20cm by 60cm by 3mm aluminium.
more videos about plowing:
https://www.youtube.com/watch?v=0FM2hFYzTPs&t
https://www.youtube.com/watch?v ysOO3XsOXE&t
My first plow on HPI E-savage:
https://www.youtube.com/watch?v=gA6bX9t7oLA&t
Hydraulic:
https://www.youtube.com/watch?v=WaeEBXaj-vA&t
https://www.youtube.com/watch?v=jLYJOSKB4QU
https://www.youtube.com/watch?v 2gwtHt5AxA
making cylinder:
https://www.youtube.com/watch?v=QRg0ZAvxVFk&t
And just a bit summit bashing in winter:
https://www.youtube.com/watch?v=NLKK_PvaKSU
Traxxas Summit is my far far favorite car, and i got lot of cars until now, its great for easy chill driving and for crawling, its simple unstoppable, so just one more video about sunday driving:
https://www.youtube.com/watch?v=ofaVjYpYDNw
If you interested for more videos about snow plow, please let me know.
I also got one new plow for traxxas just like that one if someone interested.
Thanks for watching.
Hope you enjoy in video and welcome to watch my other channel:
Tintek33_other
https://www.youtube.com/channel/UCk9akKpWakv8Gi8wyNPnPHA
Tine Sedej:
https://www.youtube.com/channel/UCNwj7T3yDfUbmARRHERF8QA
Foto, video & editing: Tine Sedej
Camera: Sony A6500, Sony A6000, Gopro4 black, Dji osmo+
Music is from YouTube audiolibrarry:
The Hunter - Audionautix
Now Launch - The Brothers Records
Skladba The Hunter izvajalca Audionautix je licencirana z licenco Creative Commons Attribution (https://creativecommons.org/licenses/by/4.0/)
Izvajalec: http://audionautix.com/")
![DT2236C Digital Laser / contact RPM Tachometer [unbox / review / first test]](https://i.ytimg.com/vi/hGeMAI1ir2M/mqdefault.jpg "DT2236C Digital Laser / contact RPM Tachometer [unbox / review / first test]
Hy There, In this video ill show you my new rpm measuring tool i got from banggood.Really usefull tool for awesome price.You can buy these items here:
(this is my affiliate links, if you buy from that links you get cheaper, and I get a piece of cake)
DT2236C Digital Laser / contact Tachometer
https://www.banggood.com/custlink/3GmEr5RTBe
coupon code: BG169986
discount price: $19.99
exp:31.8
Other tachometers (analog, engine, marine, laser...):
https://www.banggood.com/custlink/vKGhJVE7N3
Description :
DT2236C Digital Laser RPM Tachometer Contact Measurement Tool
Features :
Stylish, comfortable to use and easy to operate.
Laser / contactless ID cards, meet the needs of measurement occasions.
Wide measurement range, high resolution, fully functional.
The max / min / final value record.
Specification :
Show : 5 LCD display, the subtitles length is 10mm
Power : 4 x AA alcaline batteries
Instrument Size : 215 (L) x 65(W)x38 (H) mm
Annex : Retail box, reflective paper (9 centimeters x2), tapered adapter, funnel-shaped adapter, wire-speed ferry.
Test Distance : Approx.3cm - 2m
Functional Range Resolution Uncertainty
Speed 2.5~999.9 0.1RPM ±(0.05%+1d)
1000~99999 1RPM
Speed Line 0.05~99.99 0.01M/min
100.0 More 0.1M/min
English language was always pain in the a** for me, I respect every correction, but please be gentle
Thanks for watching.
if you want to support me for more projects like this, my paypal is:
https://www.paypal.me/TinC33
Hope you enjoy in video and welcome to watch my other channel:
Tine Sedej:
https://www.youtube.com/channel/UCNwj7T3yDfUbmARRHERF8QA
Foto, video & editing: Tine Sedej
Camera:
Sony A6500 [sel 18-200 f3,5-5,6 Zeiss touit 50 2.8 macro]
Sony A6000 [sel 30 f3.5macro Sigma 30 1.4]
GoPro 7 Black
Music is from: YouTube audiolibrary
1: Heads Up - The 126ers
2: Warships - The 126ers
3: See You On The Otherside - The 126ers")
