Make This DIY Concrete Log Holder for Your Fireplace @DIYPETE
Make This DIY Concrete Log Holder for Your Fireplace  @DIYPETE
Uploaded November 2015 | Updated November 2026, 1 day ago
How to make a Concrete Log Holder to hold and dry your firewood next to the fireplace. This concrete and wood design is very clean, minimal, and modern. The whole project does not take very long and can be done on a small budget.

For more info, project photos, and downloadable plans check out:
diypete.com/LogHolder
Download Plans: gumroad.com/l/LogHolder

*Note that these are affiliate links, meaning that when you buy something that is recommended below, it helps support the Channel. Thanks in advance!

*Tools Needed
Miter Saw​ - amzn.to/1VUVo8s
Circular Saw - amzn.to/1OxNa7k
Drill​ - amzn.to/1OxMfnt
Clamps​ - amzn.to/1LwiDEs
Kreg Jig - amzn.to/1X7Bd9H
Speed Square - amzn.to/20r5uTC
Orbital Sander - amzn.to/1VUVNYy
Tape Measure, Ruler, Pencil
Eye and Ear protection
Table Saw (optional) - amzn.to/1X7Eje5

Need more tool recommendations or curious about the tools I trust and use in my builds? Visit my Amazon Store to find everything I recommend for DIY projects big and small! amazon.com/shop/petesveen?ref_=cm_sw_r_cp_ud_aipsfshop_2HRAJ4RJR0J89C2ST1F4

*Supplies Needed
Melamine for the Form
2.5 Bags of Quikrete Mix - Quikrete 5000 $5 per bag
5 Minute Epoxy by Gorilla Glue - amzn.to/1Q3OfUK
Construction Grade Adhesive - amzn.to/1Q8MZPq
Concrete Sealer - amzn.to/1OlAII5
1 ¼” Kreg Screws - amzn.to/20r5O4J
1 ½” Wood Screws

Cut the Wood
We'll start this project by marking and making cuts on the melamine sheet for the concrete form. The melamine form has two parts, an outer box and an inner box that we’ll refer to throughout these plans. Refer to the cut list in the free, downloadable plans for all of the parts, I’d recommend marking and cutting with a circular saw or table saw.

Assemble the Outer Box
We’ll assemble the melamine boxes with screws, being sure to pre-drill pilot holes for the screws to go into. Line up the outer box pieces and start pre-drilling and screwing it together. Make sure that everything is level and flush with the form.

Assemble the Inner Box
The inner box will be screwed together with pocket holes done on a Kreg Jig. Refer to the video for further direction on screwing together and assembling the inner box. Set your Kreg Jig and Bit to the ¾” setting and the box will go together with 1 ¼” Kreg Screws. Again, make sure that everything is level and flush.

Connect the Boxes Together
Once you have built both the inner and outer boxes out of melamine, we’ll need to screw them together to make the melamine form ready for concrete! Now would be a good time to spray everything down with 100% alcohol and give it a good clean, before pouring the cement in.

Mix the Cement and Pour into Form
Once your form is completely built and screwed together, we’ll mix up the cement that will be poured into the melamine form. I did use Quikrete’s Countertop Mix for this project, yet it could be done with very similar results and major cost savings using Quikrete’s 5000 Mix.

Pack the Cement into the Form & Reinforce
We want to be sure that the cement mixture fills any and all voids in the form, so pack it into the form with a piece of scrap wood or something similar. Once it's been packed in and vibrated then we can add bars of rebar. Scrape, level, and trowel the top and make sure the form is completely filled with the cement mixture.

Let Concrete Cure, Then Remove the Form
Let the cement mixture harden and cure into concrete for the recommend time given by the manufacturer of the product. Once it has completely cured, we can remove the melamine form. Unscrew everything and carefully pull the parts off. Now we’ll move onto some light woodworking for the removable bench top / shelf.

Cut and Assemble the Wood Top
Now we’re ready to make the wood bench top / shelf for the top of the concrete log holder. Refer to the cut list in the free, downloadable plans for the dimensions and cuts for this shelf. Cut your pieces to size and then prepare for assembly.

Sand and Finish the Concrete
Now we’ll want to sand the whole concrete shape down, easing the edges, smoothing all surfaces, and preparing it for the finishing sealer.

----
Looking for more DIY videos? Be sure to check out our channel and subscribe for updates!

Looking for woodworking, concrete working, and other DIY projects plans to follow? You can download plans for free at gumroad.com/DIYPETE and premium plans available at diypete.com/diy-project-plans


Facebook: facebook.com/DiyProjectsWithPete
Instagram: instagram.com/diypete

DIYPETE.com
1627 W Main Street Suite 182
Bozeman, Montana 59715

#firewood #concreteprojects #fireplace
Make This DIY Concrete Log Holder for Your FireplaceDIY Gas Fireplace With Concrete TabletopThe Bucket Dump to fix rough iceUpdate 10: Time to paint the kid’s playhouseHow to Make Floating Shelves - DIY Wood Floating ShelvesShop Tour - 100K subscribers - and Tool Scholarships!Installing Cable Railing on Your Deck | Full TutorialFirst scoop of the rink build | 2018 Flashback!Today’s progress on the oversized storage bin for package deliveriesSimple closet shelves you can build in a weekend to get organized! | Modular shelvesWatch Us Build a Standing Desk Top Step by Step!DIY Modern Concrete Log Holder | Step by Step
DIY PETE |

Make This DIY Concrete Log Holder for Your Fireplace

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER