Uploaded March 2019 | Updated November 2026, 1 day ago
Analog Board recapping walkthrough video covers CRT discharge, flyback replacement and screen adjustments. Use Chrome to watch in 4K.
🔍 INDEX
0:00 Intro
2:48 Analog Board Revisions
5:33 4-pin Connector P1 (often burned)
6:12 Mouser Cart overview
8:19 Safety, CRT Discharge
11:14 Removing Analog Board
13:45 Recapping
39:14 Flyback Replacement
44:54 Silenx Fan
45:51 Reassembly
53:14 Testing & Adjustments
1:03:40 Closing Remarks
1:05:50 Why should you watch this entire video?
🛠 TOOLS:
• Plastic TV alignment tools: amzn.to/2Scykul
For making CRT adjustments on the white-covered side of the analog board. NEVER use metal! It must be ALL PLASTIC!
• Torx T15 with LONG neck: amzn.to/2ScAskx
• Bulldog Clip (helpful to pry off back case): amzn.to/2H7lIhF
• Phillips (+) head screw driver
• Discharge tool or flat-head screwdriver with a wire with alligator clips, for discharging the CRT -- ALWAYS done with the power off and power cord disconnected!
• Soldering iron with °F-only LCD & Solder Kit (80W, cheap!): amzn.to/36BYi0K
or
• Soldering Station (120W, ESD safe): amzn.to/30g1Frt
or
• HAKKO (Japanese) Soldering Station (70W ceramic core): amzn.to/2YvIo42
• Solder (Leaded Rosin Core 0.82mm): amzn.to/3GzJbVl
• Desoldering wick (Amazon US): amzn.to/3iMAnA5
💁♂️TIP: Set soldering iron temperature to 350°C. Don't use lead-free solder.
• 99% ISO Alcohol (Spray Bottle!): amzn.to/3ae4fG6
• 99% ISO Alcohol: amzn.to/3NoFkxN
• 99% ISO Alcohol: amzn.to/2YsK8v3
💁♂️3 alcohol choices because it's often out of stock.
• Voltmeter (Cheap!): amzn.to/2H1S7Ge
• Hot-Glue Gun & sticks: amzn.to/39hBfav
• Heat gun or very strong hair dryer that can melt hot glue, so you can remove some of the stock capacitors more easily after desoldering them -- some are hot-glued.
• Used toothbrush for scrubbing away the flux after you finish soldering in all your replacement capacitors. You can also use the opposite end of a toothbrush if you need to make adjustments on the Yoke as shown in my video.
• Swabs, for dipping in the alcohol if you need to clean up any spilled electrolyte from old, leaking capacitors.
• Rubber gloves (or any electrically insulated gloves) if you need to make adjustments around the CRT Yoke, especially with the power switched on.
🤓 USEFUL TOOL for Super-Geeks:
• DE-5000 Handheld LCR Meter (Amazon US): amzn.to/2ScttJz
The absolute best handheld meter to check the ESR of capacitors. Amazon link comes with all 3 accessories: TL-21, TL-22 & TL-23. If you buy this to check your caps, feel free to post your ESR measurements of the Analog Board caps in the Comments section, and be sure to let me know which Frequency you used -- (e.g., 120Hz, 1kHz, etc.).
MENTIONED IN MY VIDEO:
• Capacitor List (Mouser Cart): bit.ly/37metyA
⚠️ If you choose your own capacitors, ensure the Lead Spacing matches the Analog Board holes. All other caps in my Mouser list sit flush with the board. Carefully consider the Height of your caps so you don't choose caps so tall they stick out and touch the CRT.
• Replacement connector pair for P1 is sold on Mouser:
15-31-1046: bit.ly/3blRW6M
19-09-1049: bit.ly/2w0DXTC
Gold Terminals: bit.ly/3GHLwgF
Standard Terminals: bit.ly/3oESSey
Product photo on Mouser is wrong but Description clarifies that there are "4 Positions." I bought the 2 connectors & gold terminals.
• SilenX IXP-34-16 60x25mm fan has been discontinued. Get this Noctua Fan instead:
amzn.to/3YrLbK3
• Mac Classic & SE Repair & Upgrade Secrets by Larry Pina: amzn.to/388LrC1
▶NOTE: You can freely access the Larry Pina book from Archive.org if you register, login & click the "Join waitlist" button here: bit.ly/2Ttq1ro
It works like a library book in that you can access it freely, but for a limited time. Special thanks to Karsten Kruse for having mentioned this.
💾 Lode Runner game: bit.ly/2HbVtsj
💵 NOTE: Your price on Amazon (US only) is the same even if you don't click the "amzn.to" Affiliate links above, but if you do click & purchase within 24 hours, Amazon may pay me a small commission on all qualifying items in your Cart (even items not linked above).
📕 TECHNICAL INFO:
• Analog Board Schematic: bit.ly/2YDryOt
• SE/30 Service Manual: bit.ly/2TweGLP
• Classic Mac Repair Notes: bit.ly/2J7NVsw
🗣️ 68kMLA Compact Mac Forum: bit.ly/2u06Mew
🗣️ Vintage Apple Macintosh Enthusiasts FB Group: bit.ly/2NTF5Ny
OTHER VIDEOS:
🍿 Recapping the DiiMO 50MHz 68030 PDS accelerator: youtu.be/BWesQglkZPw
🖥 27" iMac (2009-2011) Video Card Bake: youtu.be/6BJGLFCigdA
🎬 For SE & SE/30:
• SONY PSU recapping: youtu.be/nSZ8QsNUxDM
• SEASONIC replacement PSU: youtu.be/hiN7mP9iQxA
💰SUPPORT MY WORK
paypal.me/supportJDW
📺 SUBSCRIBE:
youtube.com/c/JDW11/?sub_confirmation=1
#Apple #Macintosh #JDW
Analog Board recapping walkthrough video covers CRT discharge, flyback replacement and screen adjustments. Use Chrome to watch in 4K.
🔍 INDEX
0:00 Intro
2:48 Analog Board Revisions
5:33 4-pin Connector P1 (often burned)
6:12 Mouser Cart overview
8:19 Safety, CRT Discharge
11:14 Removing Analog Board
13:45 Recapping
39:14 Flyback Replacement
44:54 Silenx Fan
45:51 Reassembly
53:14 Testing & Adjustments
1:03:40 Closing Remarks
1:05:50 Why should you watch this entire video?
🛠 TOOLS:
• Plastic TV alignment tools: amzn.to/2Scykul
For making CRT adjustments on the white-covered side of the analog board. NEVER use metal! It must be ALL PLASTIC!
• Torx T15 with LONG neck: amzn.to/2ScAskx
• Bulldog Clip (helpful to pry off back case): amzn.to/2H7lIhF
• Phillips (+) head screw driver
• Discharge tool or flat-head screwdriver with a wire with alligator clips, for discharging the CRT -- ALWAYS done with the power off and power cord disconnected!
• Soldering iron with °F-only LCD & Solder Kit (80W, cheap!): amzn.to/36BYi0K
or
• Soldering Station (120W, ESD safe): amzn.to/30g1Frt
or
• HAKKO (Japanese) Soldering Station (70W ceramic core): amzn.to/2YvIo42
• Solder (Leaded Rosin Core 0.82mm): amzn.to/3GzJbVl
• Desoldering wick (Amazon US): amzn.to/3iMAnA5
💁♂️TIP: Set soldering iron temperature to 350°C. Don't use lead-free solder.
• 99% ISO Alcohol (Spray Bottle!): amzn.to/3ae4fG6
• 99% ISO Alcohol: amzn.to/3NoFkxN
• 99% ISO Alcohol: amzn.to/2YsK8v3
💁♂️3 alcohol choices because it's often out of stock.
• Voltmeter (Cheap!): amzn.to/2H1S7Ge
• Hot-Glue Gun & sticks: amzn.to/39hBfav
• Heat gun or very strong hair dryer that can melt hot glue, so you can remove some of the stock capacitors more easily after desoldering them -- some are hot-glued.
• Used toothbrush for scrubbing away the flux after you finish soldering in all your replacement capacitors. You can also use the opposite end of a toothbrush if you need to make adjustments on the Yoke as shown in my video.
• Swabs, for dipping in the alcohol if you need to clean up any spilled electrolyte from old, leaking capacitors.
• Rubber gloves (or any electrically insulated gloves) if you need to make adjustments around the CRT Yoke, especially with the power switched on.
🤓 USEFUL TOOL for Super-Geeks:
• DE-5000 Handheld LCR Meter (Amazon US): amzn.to/2ScttJz
The absolute best handheld meter to check the ESR of capacitors. Amazon link comes with all 3 accessories: TL-21, TL-22 & TL-23. If you buy this to check your caps, feel free to post your ESR measurements of the Analog Board caps in the Comments section, and be sure to let me know which Frequency you used -- (e.g., 120Hz, 1kHz, etc.).
MENTIONED IN MY VIDEO:
• Capacitor List (Mouser Cart): bit.ly/37metyA
⚠️ If you choose your own capacitors, ensure the Lead Spacing matches the Analog Board holes. All other caps in my Mouser list sit flush with the board. Carefully consider the Height of your caps so you don't choose caps so tall they stick out and touch the CRT.
• Replacement connector pair for P1 is sold on Mouser:
15-31-1046: bit.ly/3blRW6M
19-09-1049: bit.ly/2w0DXTC
Gold Terminals: bit.ly/3GHLwgF
Standard Terminals: bit.ly/3oESSey
Product photo on Mouser is wrong but Description clarifies that there are "4 Positions." I bought the 2 connectors & gold terminals.
• SilenX IXP-34-16 60x25mm fan has been discontinued. Get this Noctua Fan instead:
amzn.to/3YrLbK3
• Mac Classic & SE Repair & Upgrade Secrets by Larry Pina: amzn.to/388LrC1
▶NOTE: You can freely access the Larry Pina book from Archive.org if you register, login & click the "Join waitlist" button here: bit.ly/2Ttq1ro
It works like a library book in that you can access it freely, but for a limited time. Special thanks to Karsten Kruse for having mentioned this.
💾 Lode Runner game: bit.ly/2HbVtsj
💵 NOTE: Your price on Amazon (US only) is the same even if you don't click the "amzn.to" Affiliate links above, but if you do click & purchase within 24 hours, Amazon may pay me a small commission on all qualifying items in your Cart (even items not linked above).
📕 TECHNICAL INFO:
• Analog Board Schematic: bit.ly/2YDryOt
• SE/30 Service Manual: bit.ly/2TweGLP
• Classic Mac Repair Notes: bit.ly/2J7NVsw
🗣️ 68kMLA Compact Mac Forum: bit.ly/2u06Mew
🗣️ Vintage Apple Macintosh Enthusiasts FB Group: bit.ly/2NTF5Ny
OTHER VIDEOS:
🍿 Recapping the DiiMO 50MHz 68030 PDS accelerator: youtu.be/BWesQglkZPw
🖥 27" iMac (2009-2011) Video Card Bake: youtu.be/6BJGLFCigdA
🎬 For SE & SE/30:
• SONY PSU recapping: youtu.be/nSZ8QsNUxDM
• SEASONIC replacement PSU: youtu.be/hiN7mP9iQxA
💰SUPPORT MY WORK
paypal.me/supportJDW
📺 SUBSCRIBE:
youtube.com/c/JDW11/?sub_confirmation=1
#Apple #Macintosh #JDW
![MacSD Product Review [SCSI to SD]
Like SSDs in modern computers, MacSD is a flash drive replacement for spinning platter SCSI hard drives in vintage Macs. Usage, benchmarks and brief comparisons with competing SCSI2SD products are presented.
🔍 INDEX
0:00 Intro
1:56 Key Features
3:40 Compatibility
4:32 Mounting Bracket
8:19 SCSI Termination
11:02 Disk Images
13:25 Composites
14:06 Configuration
19:53 File Fragmentation
22:14 Firmware Updates
26:07 Enhancing MacSD
28:54 General Usage
38:16 Benchmarking
49:02 Windows Support
49:37 Pricing & Purchase
51:32 Closing Thoughts
💳 BUY
Dont forget to watch the end of my video for a MacSD Discount Code!
• MacSD: https://bit.ly/3x9JUZl
• Multi-colored wire: https://amzn.to/3srYO9P
• RGB LEDs CLEAR (Common Cathode): https://amzn.to/2QvGPSF
• RGB LEDs FROSTED (Common Cathode): https://amzn.to/3ec7rAd
• Sony Tough 64GB V60 SD Card: https://amzn.to/2RKqfPE
• Kingston 32GB V90 SD Card & Reader!: https://amzn.to/2RAReNl
(Slower than the Sony V60 in MacSD.)
• Torx T15 with T-grip & 9 neck: https://amzn.to/3ceQqWk
• Torx T15 with 18 neck: https://amzn.to/2ScAskx
• FloppyEMU: https://www.bigmessowires.com/floppy-emu/
• Anti-static pad with Wrist Strap (16x24 / 41x61cm): https://amzn.to/3bfAE9Z
• Wall socket Ground adapter for banana-jack Wrist Strap: https://amzn.to/2Yvq5ge
💵 NOTE: Your price on Amazon (US only) is the same even if you dont click the amzn.to Affiliate links above, but if you do kindly click and purchase within 24 hours, Amazon may pay me a small commission on all qualifying items in your Cart (even items not linked above).
💾 SOFTWARE
• My Benchmark Results (ScreenShots & DSK image): https://bit.ly/2QQOMC4
(I added screenshots as well as new benchmarks to the DSK on April 24, 2021.)
• Bootable Drive Images: https://www.savagetaylor.com/downloads/downloads-macintosh/
• Mini vMac Blanks: https://bit.ly/3dxQRvK
• Mini vMac Download: https://bit.ly/3swZkU9
• Basilisk II Download: https://bit.ly/3aqOY1P
• SD Card Formatter (FAT32 MBR part 12, 0x0C): https://bit.ly/3gq6uHk
• Make B&W bitmaps from your photos: https://29a.ch/ditherlicious/
(Resolution of your submitted photos is key to a good result. Try 640x480 to start.)
📚 REFERENCE
• MacSD Manual, Firmware, etc.: http://macsd.com
• Mac Classic install: https://bit.ly/3xepui4
• MicroMac DiiMO 50MHz 68030 PDS Accelerator info (photo is wrong): https://bit.ly/3n8havI
• Photos of my boxed DiiMO kit: https://bit.ly/3xbD8m1
• Photos of my Daystar Turbo 040 PDS Accelerator: https://bit.ly/3vb5dYX
• Retro Guy Blog (Mac Plus Diode): https://bit.ly/2QFQ0A8
• Mac Plus Schematic: https://bit.ly/2Qa6bWy
• Format SD as 0x0C using the Terminal: https://bit.ly/3go5Nhz
NOTE! Apples Disk Utility formats FAT32 MBR as part 11, 0x0B.
• To get crisp pixels in Basilisk II on a Retina Mac, install and find hidden file .basilisk_ii_prefs in your Home folder. CMD-Shft-. to show/hide hidden files. Edit prefs file in TextEdit to add scale_nearest true. LOCK prefs file to prevent your changes from being deleted. Use SwitchResX to change your 5K iMacs resolution to 1920x1080 (not HiDPI) to get the cleanest full screen results, or consider adding a second line to the prefs to Double the pixel size: scale_nearest true. More info here: https://bit.ly/3x8dBtL
🎬 My Sony Tough SD Card Review: https://youtu.be/73gZlctLe8g
🗣 Helpful Groups:
• 68kMLA: http://68kmla.org
• Apple Macintosh Enthusiasts: https://bit.ly/2QCtbgL
• Vintage Apple Macintosh Enthusiasts: https://bit.ly/2YgpDRb
• Vintage Macintosh Restoration & Preservation: https://bit.ly/2XKFzfK
💁♂️SUPPORT THIS CHANNEL💰
https://www.paypal.me/supportJDW
📺 SUBSCRIBE:
http://www.youtube.com/c/JDW11/?sub_confirmation=1
#macsd #scsi2sd #macintosh #JDW MacSD Product Review [SCSI to SD]](https://i.ytimg.com/vi/zwz6qMC2ZE4/mqdefault.jpg)
![SPIISD v2 by Keros Mac Mods [Part 1 of 2]
Watch me assemble Kay Kobas SPIISDv2 and show 2 enclosures I had printed at JLCPCB.Compatible with Apple II Plus, IIe, IIc, IIc Plus & IIgs.
Part II video: https://youtu.be/gRluyxiFoGM
🔎 *INDEX*
0:00 — Intro
1:04 — Requirements
2:14 — The Kit
3:17 — Pricing
6:41 — Kit Assembly
29:43 — Adapter Assembly
38:55 — First Test
39:34 — 3D-printed Cases
47:06 — Closing Thoughts
🛒 *KEROS MAC MODS*
_(When accessing Kays store, use Chrome or Firefox, not Safari)_
• SPIISDv2 kit: https://bit.ly/42FO5P1
• All Products on Keros Mac Mods: https://en.infinityproducts.co.jp/shop-1
• 1.54 LCD: https://www.aliexpress.com/item/1005009104685556.html
🛒 *SOLDERING & CLEANING*
• 99% ISO Alcohol: https://amzn.to/3R5TRCk
• MG Chemicals Flux: https://amzn.to/3kuAcsZ
• Desoldering wick: https://amzn.to/4jbseUW
• Generic Solder 100g (60-40 Leaded Rosin Core 0.6mm, 2% flux): https://amzn.to/3FDRscn
or
• Kester Solder 454g (60-40 Leaded Rosin Core 0.8mm, 3.3% flux): https://amzn.to/3tLFwT9
• 2-spool Solder Holder: https://amzn.to/39hIMbt
• Hakko 599B Tip Cleaner: https://amzn.to/3RHy5o4
• Hakko Soldering Station (FX888DX): https://amzn.to/4kEttgq
• Hakko Fume Extractor: https://amzn.to/3MApWyb🛒 *TOOLS*
• Needle Nose Pliers: https://amzn.to/43U0WOc
• Helping Hands: https://amzn.to/4llkFfM
• 5x or 10x illuminated Magnifier: https://amzn.to/3YCySJ7
• Rubberized Vice: https://amzn.to/3x78yuX
• Vice & LED-lit 3x Magnifier & Rubberized Helping Hands: https://amzn.to/3xdAVHK
🛒 *OTHER STUFF*
• SD Cards I use for almost everything: Gigastone 16GB MLC V30: https://amzn.to/4jiEhiK
• ROM Xc (lets you use any of the 4 IIc ROMs): https://bit.ly/4a0Ia8U
• 3D Printing at JLPCB: https://jlc3dp.com/3d-printing-quote
• Rubber Feet for a 3D printed case: https://amzn.to/4jb34G0
• Gray 30cm/1 Ribbon Cable, 20-pin : https://amzn.to/3G9yP3y
• Rainbow 30cm/1 Ribbon Cable, 20-pin: https://amzn.to/4lC0daP
_NOTE: You can always buy a Ribbon cable from Kay, instead of Amazon._
• Drive Switcher from BMOW: https://bit.ly/3GbaD0P
(If you have one like I do, Kay recommends removing when using SPIISDs Adapter, but BMOW says you can just short the 2 dangling wires from the internal Drive Switcher board and then you use Kays Adapter with the SPIISDv2.)
• MacEffects BLACK Case & Keyboard: https://bit.ly/3CsStG2
• EYOYO 10 IPS Display: https://bit.ly/4gSm8ah
• KARATEKA T-shirt (mine is Navy): https://bit.ly/48Yx6ID
• Mac Motherboard Reloaded Services from CayMac: https://bit.ly/3YnMLgP
💾 *DOWLOADS*
• Javier Riveras CASE: https://bit.ly/3RTmzGQ
• Stephen Arsenaults CASE (DONT print the Lens at JLC): https://bit.ly/4ctHSIy
• Allen Williams CASE: https://bit.ly/4ie6Ddj
• Bruce Raynes CASE: coming in late Sept. 2025!
• Total Reply II: https://archive.org/details/TotalReplay2
📚 *REFERENCE*
• SPIISDv2 Assembly: https://tinyurl.com/3248728t
• SPIISDv2 Usage (& Case Photos): https://tinyurl.com/47ncys5x
• Video by @BigBadBench : https://www.youtube.com/live/Wj6tyfeDalo
• SmartPort protocol was designed for the UniDisk 3.5: https://tinyurl.com/mr29v2ea
📚 *VINTAGE SMARTPORT HARD DISKS*
• Chinook CT80c: https://tinyurl.com/5ftj79dz
• PROAPP: https://tinyurl.com/yyppd7fa
• Quark QC10: https://tinyurl.com/4656nbbx
• CIRTECH Uni-Mate (if you have a link, please email it to me!)
🙇♂️ *SPECIAL THANKS* to Kay Koba of Keros Mac Mods for answering my many questions and of course for making amazingly useful gadets like this! Thanks also to Stephen & Javier for feedback regarding their cases!
🙏 *THANK YOU, Paypal Supporters!* (since my last video)
• Brian Gorham 🇺🇸 (🥇TOP repeat supporter)
• Mark B Newlon 🇺🇸 (repeat supporter)
• Philippe Astier 🇫🇷 (monthly supporter)
• Mauro Acciaccaferri 🇮🇹 (monthly supporter)
• Gavin Maxwell 🇦🇺 (monthly supporter)
💰*HOW TO SUPPORT THIS CHANNEL*
https://www.paypal.me/supportJDW
📺 *Please SUBSCRIBE:*
http://www.youtube.com/c/JDW11/?sub_confirmation=1
🎬 *MY VIDEOS*
https://www.youtube.com/user/JDW26/videos
#SPIISDv2 #KerosMacMods #AppleIIc #JDW1 SPIISD v2 by Keros Mac Mods [Part 1 of 2]](https://i.ytimg.com/vi/zyInduIstWk/mqdefault.jpg)