Mark Lindsay CNC | Live Q&A #253 – Vectric V12+ for the Absolute Beginner – Part 1 @MarkLindsayCNC | Uploaded 2 months ago | Updated 2 hours ago
Live Q&A #253 – Vectric V12+ for the Absolute Beginner – Part 1
More down here ↓↓↓ Click MORE!
In this live stream I’ll be talking about the new Vectric V12+ for the Absolute Beginner video series. I’ll answer your questions regarding Part 1 of this series, my plans for this series, and any other question you may have about Vectric Version 12. This will be in addition to our regular Open Live Q&A, where I'll answer your general CNC or Vectric Software questions.
Link to Vectric V12+ for the Absolute Beginner – Part 1 – Job Setup and Vector Selection: youtu.be/6RJ1KJau6ww
Remember that I host these Live Q&A discussions every Sunday at Noon Pacific Time, 3 pm Eastern Time, so SUBSCRIBE to my channel to stay up to date!
As usual, if you have any comments or questions, please put ‘em in the comment section below.
Thanks for watching!
Links to videos, Playlists, YouTube channels, products, and supplies as discussed in this video:
Link to my NEW Vectric V12+ for the Absolute Beginner playlist: youtube.com/playlist?list=PLLuYLaC3-QRMFBT-TzIbMyGtuBurt8GCQ
Link to my video collaboration with @vectric Making Your First V-Carved Inlay: youtube.com/watch?v=yUaSsL4F6_E
Link to @vectric video The BBQ Board: youtube.com/watch?v=VplcNZrUzmM
Link to replay of Rob Sandstrom's live stream Follow-up on Vector Overlap, Epoxy Inlay, and Other Open Questions: youtube.com/watch?v=_MD4W6O092s
Link to 3M Radial Bristle Disc 120 grit: amzn.to/3yhBtRe
Link to Radial Bristle Disc 80 grit: amzn.to/3WEiSbu
Link to Nylon Sanding Brush set for Drill: amzn.to/4dk2UIT
Link to Michael Mezalick’s YouTube channel: youtube.com/user/mezalick
Link to CNCnutz (Peter Passuello’s) YouTube channel: youtube.com/c/cncnutz
Link to Laney Shaughnessy’s YouTube channel SpindleTV: youtube.com/@SpindleTV
Link to the Vectric for the Absolute Beginner Playlist (Version 11.5 and older): youtube.com/playlist?list=PLLuYLaC3-QRNuVTej2P5emp1D4_Tm774p
Link to the V-Carving for the Absolute Beginner playlist (Version 11.5 and older): youtube.com/playlist?list=PLLuYLaC3-QROVf1Ua9BhGCzBty2FhZFmE
Click the JOIN button to get access to perks: youtube.com/marklindsaycnc/join
Please remember that I am NOT a CNC expert, and I cannot help you troubleshoot your CNC router. Every CNC router, controller, and controller software is different. Your best option is to contact your CNC manufacturer’s Tech Support division, or look for a Support Forum or Support Community through their website. They are the people who know your machine best, while I would only be guessing.
Link to Mark’s Other Channel. My second YouTube channel that’s dedicated to non-CNC related projects. youtube.com/channel/UCXMdT30E3tx7myvt9jGx-pA
______________________________________________________________________________
If you’d like to support my channel, help fund the shop/shed build, and help with the making of future videos, you can donate by using the link below:
PayPal: paypal.me/MarkLindsayCNC
___________________________________________________________________________________
Get your Official Mark Lindsay CNC T-shirts and coffee mugs here:
http://marklindsaycnc.com/index.php/product-category/logo-products
marklindsaycnc.com is sponsored by Harneal Media – a website developing company that specializes in websites for the maker community. Find out more at:
harnealmedia.com
___________________________________________________________________________________
For more info, or to configure an Avid CNC of your own, visit their website: avidcnc.com
For more information on, or to download a free trial of Cut 2D, VCarve, or Aspire, visit the Vectric website at:
http://www.vectric.com
For more tutorials on how to use Vectric Software, as well as some very cool projects, visit and subscribe to Vectric’s YouTube channel: youtube.com/user/Vectric
Interested in hosting your own live streams? Check out StreamYard: streamyard.com/pal/5708919750000640
__________________________________________________________________________________
Some links may be affiliate or sponsor links. Purchasing or even clicking through these links helps with the making of future videos.
I appreciate your support!
This video is for informational and entertainment purposes only.
#Vectric #VCarvePro #Aspire
Check out StreamYard: streamyard.com/pal/d/5708919750000640
Live Q&A #253 – Vectric V12+ for the Absolute Beginner – Part 1
More down here ↓↓↓ Click MORE!
In this live stream I’ll be talking about the new Vectric V12+ for the Absolute Beginner video series. I’ll answer your questions regarding Part 1 of this series, my plans for this series, and any other question you may have about Vectric Version 12. This will be in addition to our regular Open Live Q&A, where I'll answer your general CNC or Vectric Software questions.
Link to Vectric V12+ for the Absolute Beginner – Part 1 – Job Setup and Vector Selection: youtu.be/6RJ1KJau6ww
Remember that I host these Live Q&A discussions every Sunday at Noon Pacific Time, 3 pm Eastern Time, so SUBSCRIBE to my channel to stay up to date!
As usual, if you have any comments or questions, please put ‘em in the comment section below.
Thanks for watching!
Links to videos, Playlists, YouTube channels, products, and supplies as discussed in this video:
Link to my NEW Vectric V12+ for the Absolute Beginner playlist: youtube.com/playlist?list=PLLuYLaC3-QRMFBT-TzIbMyGtuBurt8GCQ
Link to my video collaboration with @vectric Making Your First V-Carved Inlay: youtube.com/watch?v=yUaSsL4F6_E
Link to @vectric video The BBQ Board: youtube.com/watch?v=VplcNZrUzmM
Link to replay of Rob Sandstrom's live stream Follow-up on Vector Overlap, Epoxy Inlay, and Other Open Questions: youtube.com/watch?v=_MD4W6O092s
Link to 3M Radial Bristle Disc 120 grit: amzn.to/3yhBtRe
Link to Radial Bristle Disc 80 grit: amzn.to/3WEiSbu
Link to Nylon Sanding Brush set for Drill: amzn.to/4dk2UIT
Link to Michael Mezalick’s YouTube channel: youtube.com/user/mezalick
Link to CNCnutz (Peter Passuello’s) YouTube channel: youtube.com/c/cncnutz
Link to Laney Shaughnessy’s YouTube channel SpindleTV: youtube.com/@SpindleTV
Link to the Vectric for the Absolute Beginner Playlist (Version 11.5 and older): youtube.com/playlist?list=PLLuYLaC3-QRNuVTej2P5emp1D4_Tm774p
Link to the V-Carving for the Absolute Beginner playlist (Version 11.5 and older): youtube.com/playlist?list=PLLuYLaC3-QROVf1Ua9BhGCzBty2FhZFmE
Click the JOIN button to get access to perks: youtube.com/marklindsaycnc/join
Please remember that I am NOT a CNC expert, and I cannot help you troubleshoot your CNC router. Every CNC router, controller, and controller software is different. Your best option is to contact your CNC manufacturer’s Tech Support division, or look for a Support Forum or Support Community through their website. They are the people who know your machine best, while I would only be guessing.
Link to Mark’s Other Channel. My second YouTube channel that’s dedicated to non-CNC related projects. youtube.com/channel/UCXMdT30E3tx7myvt9jGx-pA
______________________________________________________________________________
If you’d like to support my channel, help fund the shop/shed build, and help with the making of future videos, you can donate by using the link below:
PayPal: paypal.me/MarkLindsayCNC
___________________________________________________________________________________
Get your Official Mark Lindsay CNC T-shirts and coffee mugs here:
http://marklindsaycnc.com/index.php/product-category/logo-products
marklindsaycnc.com is sponsored by Harneal Media – a website developing company that specializes in websites for the maker community. Find out more at:
harnealmedia.com
___________________________________________________________________________________
For more info, or to configure an Avid CNC of your own, visit their website: avidcnc.com
For more information on, or to download a free trial of Cut 2D, VCarve, or Aspire, visit the Vectric website at:
http://www.vectric.com
For more tutorials on how to use Vectric Software, as well as some very cool projects, visit and subscribe to Vectric’s YouTube channel: youtube.com/user/Vectric
Interested in hosting your own live streams? Check out StreamYard: streamyard.com/pal/5708919750000640
__________________________________________________________________________________
Some links may be affiliate or sponsor links. Purchasing or even clicking through these links helps with the making of future videos.
I appreciate your support!
This video is for informational and entertainment purposes only.
#Vectric #VCarvePro #Aspire
Check out StreamYard: streamyard.com/pal/d/5708919750000640
