Lead-Acid Batteries SUCK - Making The Switch to LiFePO4 (2/4) @HighTechLab
Lead-Acid Batteries SUCK - Making The Switch to LiFePO4 (2/4)  @HighTechLab
Uploaded May 2019 | Updated November 2026, 3 days ago
Remember to join the Discord Server! discord.gg/wZBXf4B

In this video, I review the progress I have made in an effort to prepare my off the grid power supply room for new LiFePO4 Prismatic cells. I start out by showing the 3 pallets of dead batteries that have come and gone, and am actually looking to sell. (Email address for purchase inquiries is hightechlabftw@gmail.com) Some of the batteries were nearly new when they had failed and the failure mode they exhibited was one cell with a low specific gravity and a resting voltage of around 10.5 volts. Since my system is a series & Parallel connected system, one bad cell means the performance of the whole system is jeopardized by one out of balance battery.

I do not have time to fight with these batteries anymore to try and get life back into them. I barely have time to check the electrolyte water levels in them. As a result, 4 of the batteries ran completely dry (One of which cracked the top of the case), and many others had issues that turns into lost capacity and bigger issues.

I will be using CALB LiFePO4 cells in the next iteration of this off grid room for a few reasons - I am avoiding any batteries that are constructed of hundreds of 18650 or similiar cylindrical cells, simply because the geometry of the packs causes them to have higher internal resistance, and internal resistance equates to heat and lost power. In our off grid setups, we do not want to experience heat loss - we want every drop of power we put in to be a drop of power we get out. The Prismatic cells that I am balancing as I write this description have such a low internal resistance, on a 7 digit DMM the voltage literally did not raise when charge current was applied. This will be a very different learning curve than what I have experienced with Lead Acid, simply because lead acid is so lossy and has such a high internal resistance, the voltage goes up and up as current is applied (This is why you have a charging voltage of 14.4 volts and a low voltage of 10.5 volts.

A slightly scary scenario with this low internal resistance is similar to a capacitor discharging...There is such an insane amount of instant power available that when I connect to the inverter, I need to pre-charge the capacitors, because there is such an insanely high amount of power ready to rush in, and because capacitors can take in nearly infinite power until they are charged, I have a situation where it is possible that the inrush to the capacitors in the inverter is able to provide excess current on the traces and cause the boards and wires going into the capacitors to explode. This would not be good of course.

I'm very excited for the next few videos. From PLCs to HMI panels and more, there is going to be plenty of content coming to the channel. This is just the start. Hit that subscribe button and turn on the bell icon to see more videos like this one.

If you made it this far, which 99% of people won't, then please leave a comment below, it will be an interesting study.
Lead-Acid Batteries SUCK - Making The Switch to LiFePO4 (2/4)Using Grid Tie Inverters Off The Grid (Part 2 of 2)Running a Well Pump on Paralelled Honda GeneratorsOff Grid Power Room Rebuild PT 8Outback flexmax 80 charge controller voltage settingsOff Grid: Capacity Test of CA180 Cells for Off Grid Power SystemsLiving Off The Grid With NO POWER BILL EVERMinecraft Mod-free Paintball server!Motorcycle Ride through Copperopolis, CALiFePO4 Drops Quick At The End Of The CurveLaser cut Brass - I do this for a living!Well Drilling at Wellmont Ranch - 80 Gallons Per Minute
HighTechLab |

Lead-Acid Batteries SUCK - Making The Switch to LiFePO4 (2/4)

SHARE TO X SHARE TO REDDIT SHARE TO FACEBOOK WALLPAPER