Uploaded April 2020 | Updated November 2026, 1 hour ago
I accidentally came across Jesus' personal hand plane while cleaning my shop. I do not know how it ended up in the middle of Canada, but carbon-dating determined this plane is around 2000 years old. The restoration focuses on resurrecting all broken and missing parts of the plane so it can function once again.
I accidentally came across Jesus' personal hand plane while cleaning my shop. I do not know how it ended up in the middle of Canada, but carbon-dating determined this plane is around 2000 years old. The restoration focuses on resurrecting all broken and missing parts of the plane so it can function once again.

![Rare Bow Chainsaw [Restoration]
This restoration is on the first gasoline-powered one-man bow chainsaw ever produced. It was made by Precision Part Ltd. of Montreal, Canada in the 1940s.
It took me 5 years to find 3 separate dilapidated chainsaw motors, 2 bow bars, 1 straight bar, and 2 chains just to source all the parts to restore one function chainsaw. Unfortunately, the most complete motor happened to also be completely seized, but that is just the way it goes sometimes. Adding further to the complications, the body of the chainsaw is rumoured to be made of out of a magnesium alloy that is so high in nickel and iron that it cannot be welded, so any major repairs that require welding, cannot be made. Furthermore, the massive chain that is used on this type of chainsaw is not made anymore and all available options potentially used to the point of being unsafe.
This saw is so rare that I actually stopped trying to take it apart when I got deep inside the crankcase. I became worried that the risk of trying to hammer out shafts and bearings would put too much stress on an unweldable casting that it would crack, and then I would crack and throw myself in the garbage, never to be restored.
The bow itself is quite unique, with its patented self-tensioning mechanism, which can be seen here: https://patentimages.storage.googleapis.com/71/cd/8d/09fe8fc70b33d0/US2487322A.pdf
The restoration process took so long that you can see how long my facial hair grew by the end of the video.
In the end, this insane chainsaw design is just too much fun to use and I am definitely keeping this one for myself.
Id like to thank CRC for sponsoring this video. Ive switched to a food-grade penetrating oil from them as a more safe alternative, and it as worked just as well as the usual penetrating oils Ive used.
You can check out the products from them used in this video in the links below:
www.evapo-rust.com
www.crcindustries.com/evapo-rust/
www.crcindustries.com/smartwasher/
www.crcindustries.com/food-grade-penetrating-oil-11-wt-oz/
Help secure more tools for future videos (if you want):
https://www.patreon.com/handtoolrescue
Instagram:
https://www.instagram.com/handtoolrescue
Facebook Group - Share your restorations
https://www.facebook.com/groups/handtoolrescue
https://www.facebook.com/handtoolrescue/
Reddit - Share your restorations
https://www.reddit.com/r/HandToolRescue/
Podcast (with @jimmydiresta and Andrew Alexander) - https://anchor.fm/fitzall Rare Bow Chainsaw [Restoration]](https://i.ytimg.com/vi/Wjv75kJyZ7M/mqdefault.jpg)
![Antique Flamethrower [Restoration]
This Little Giant flamethrower/flame gun was made by the Hauck MFG. Co from the 1930s-1950s. The tool restoration was pretty straight forward, but the operation was not.
I used high-heat oil-and-gas resistant paint wherever possible. The red handle is not the original colour, I just thought it looked nice. It was nice to see that the pump still had compression and the pressure gauge still worked.
Operating this thing is not safe...at all. The shutoff valve is so far from the spout that there is a lot of kerosene left in the piping that needs to burn off before it shuts off. The flamethrower was still burning ~5min after I turned it off. I tested that valve and it works just fine, so the burning is just part of its function. I couldnt use it for very long as there is a fire ban in my area and kerosene is much harder to put out than gasoline.
This was a fun local find here in Saskatoon. I will probably put this one up for sale.
Help secure more tools for future videos (if you want): https://www.patreon.com/handtoolrescue
Instagram:
https://www.instagram.com/handtoolrescue/ Antique Flamethrower [Restoration]](https://i.ytimg.com/vi/WtGeadX_Jt4/mqdefault.jpg)

![1960s Electric Chainsaw [Restoration] (Part 1 of 2)
I always love doing chainsaw restorations. This chainsaw (Model C. E) was made by the Strunk Manufacturing Co. in the 1960s. The chainsaw happens to be electric and has a massive 26 amp motor, which puts the saw at around 4HP. That is a LOT of power for an electric chainsaw. Strunk also made versions of these for the U.S. Army in the 1960s. I have not been able to find a photo of this saw anywhere on the internet.
This saw was very dirty, especially inside the motor, which is probably the reason why it did not run. I couldnt sandblast the paint off as it contained lead. I decided to go a little bit further with this restoration and add a polished handle and bucking spikes.
The chainsaw bar oil can was the most damaged and needed a lot of work to get back to original condition.
In this video I take everything apart, clean, repair, and then paint. In Part 2, I will put it back together and get it running.
Id like to thank Evapo-Rust for sponsoring this video.
Purchase wrenches here:
www.handtoolrescue.com
Help secure more tools for future videos (if you want):
https://www.patreon.com/handtoolrescue
Instagram:
https://www.instagram.com/handtoolrescue
Facebook Group - Share your restorations
https://www.facebook.com/groups/handtoolrescue
Reddit - Share your restorations
https://www.reddit.com/r/HandToolRescue/ 1960s Electric Chainsaw [Restoration] (Part 1 of 2)](https://i.ytimg.com/vi/WzZHi90RHrE/mqdefault.jpg)


![Two-Man Chainsaw - Carburetor & Muffler [Restoration]
The time has come for this chainsaw restoration. This specific saw restoration is for me and I have been wanting to get to this tool for a long time. I started the disassembly in November 2018 and had to wait a while for some rare parts to arrive. This chainsaw is a McCulloch 99 two-man chainsaw made in 1954. The engine is 161cc and the powerhead alone is 51lbs making it one of the largest production chainsaws ever and the largest in McCullochs production line at the time.
In this video, I focus on the complicated carburetor and broken muffler. The carburetor is uniquely designed by McCulloch to ensure the chainsaw always has a reason to not start or run. It is a labyrinth of small holes and tubes that I hopefully fully cleaned. My main concern is that I wont know I did something wrong until I try and run the saw. I had to make a new gasket with some new carburetor diaphragm material that I found online as I did not trust the old gasket to function optimally.
The muffler needed a lot of work! I cut the old dented parts off and used some thicker steel pipe and sheet metal to remake the muffler. I tried to design it so it was as close to original as I can get with the tools I have available to me. I am excited to hear what it sounds like.
In the next video I will work on the main powerhead and reassemble the whole saw so we can try and cut some wood!
Wrenches are now for sale at www.handtoolrescue.com
Help secure more tools for future videos (if you want):
https://www.patreon.com/handtoolrescue
Instagram:
https://www.instagram.com/handtoolrescue
Facebook Group - Share your restorations
https://www.facebook.com/groups/handtoolrescue
Reddit - Share your restorations
https://www.reddit.com/r/HandToolRescue/ Two-Man Chainsaw - Carburetor & Muffler [Restoration]](https://i.ytimg.com/vi/ZjkIl6R3EEk/mqdefault.jpg)
![Have you ever seen a wrench like this? [Patent Remake]
In this video I recreate and massively upscale a 1910 patent for wrench/spanner. You can view the original patent documents here: https://worldwide.espacenet.com/patent/search/family/033444316/publication/GB191007671A?q=GB191007671A
This wrench design is quite odd since it uses shims or blades that swing into or out of position in order for the user to adjust the wrench to he required size of the fastener.
I decided to make a much larger version of the original for this video. The wrench I made is 12 long and 3/8 thick of 4140 steel, and the shims are 1/16 wide and made of O1 tool steel. Both the wrench body and shims were heat treated and tempered to 52HRC. The most difficult aspects of remaking this wrench are making sure the back of the shims sit perfectly against the body of the wrench so that they line up perfectly parallel when in use, and making sure the shims and the gap of the wrench mouth are perfectly divisible by 16 so non-metric fasteners fit perfectly.
Id like to thank @CRCAutoUS for sponsoring this video.
You can check out the products from them used in this video in the link below:
https://www.crcindustries.com/handtoolrescue
Wrenches, screwdrivers, and socket drivers are now for sale at https://www.handtoolrescue.com/
Watch narrated videos and help secure more tools for future videos (if you want):
https://www.patreon.com/handtoolrescue Have you ever seen a wrench like this? [Patent Remake]](https://i.ytimg.com/vi/ZspDqxx2MFY/mqdefault.jpg)
![1879 Compass Plane [Restoration]
This restoration is on a Type 1 Stanley No. 113 compass plane patented in 1879. You can view the original patent documents here:https://patents.google.com/patent/US216577
The Type 1 planes of the No. 113 were made from 1877-1880 and allowed users to plane curved wooden surfaces.
This specific plane was sent to me by a viewer.
I wanted to restore this plane as close to original as possible so I opted to japan the main body and nickel-plate the knobs. Unfortunately, you must drill out a specific pin located under the sole adjustment knob in order to fully remove it from the body of the plane. Other than that one pin, everything else was de-rusted and cleaned for reassembly.
With the blade sharpened, it preformed very well and was a lot of fun to use.
I really miss restoring hand planes as that is what got me so hooked on doing restorations in the first place.
Thanks again for https://www.evapo-rust.com for sponsoring this video.
Wrenches and screwdrivers are now for sale at www.handtoolrescue.com
Help secure more tools for future videos (if you want):
https://www.patreon.com/handtoolrescue
Instagram:
https://www.instagram.com/handtoolrescue
Facebook Group - Share your restorations
https://www.facebook.com/groups/handtoolrescue
https://www.facebook.com/handtoolrescue/
Reddit - Share your restorations
https://www.reddit.com/r/HandToolRescue/
Podcast (with Jimmy DiResta and Andrew Alexander) - https://anchor.fm/fitzall 1879 Compass Plane [Restoration]](https://i.ytimg.com/vi/aH7wUYOlTck/mqdefault.jpg)
![1902 Champion Blower & Forge Co. No. 400 Forge Blower (Part One) [Restoration]
In this video, I disassemble three separate, but similar, forge blowers in order to get all the parts needed to assemble one fully functioning forge blower. The bronze gear proved too difficult to remove without damaging some other parts, so I just left it in. I had triple of all the small parts like nuts and bolts, so my main goal was to get them off by any means. In the next video, I will paint and reassemble the forge blower.
https://www.instagram.com/handtoolrescue/ for upcoming projects. 1902 Champion Blower & Forge Co. No. 400 Forge Blower (Part One) [Restoration]](https://i.ytimg.com/vi/adJ2PMVg7hQ/mqdefault.jpg)