Uploaded November 2022 | Updated September 2026, 2 weeks ago
The Resin HotBox was created to get consistent results and fewer failures with a temperature-controlled ambient resin printer enclosure. Almost every resin prints better at specific temperature ranges, especially the higher-performance and exotic resins. The Resin HotBox enclosure also helps to trap fumes and has a built-in port to add fume extraction.
00:04 Introduction
00:18 Why Do You Need An Enclosure For A Resin Printer?
01:27 Features
03:25 Instant Access to Machine
04:09 Size and Machine Fits
05:47 LED USB BAR for Resin
06:23 Unboxing and Set Up
9:54 Conclusion
The Resin HotBox is 330mm wide x 330mm deep x 580mm tall and fits the following printers:
AnyCubic: Photon, Ultra, S, SQ, Mono, Mono SE, X, 4K, X 6K, M3, D2 DLP
Creality: Halot, Halot One, Halot One Pro, Halot One Plus, Halot Lite, Halot Sky, LD002 H, LD002 R, LD 006
Elegoo: Saturn, Saturn 2 8k, Saturn 8K, Mars, Mars Pro V2, Mars C, Mars 3, Mars 3 Pro, Mars 3 Ultra 4k
EPAX: E10, E10 8K 10.1, E10 4K, E10 4K 8.9 , E10 5K 10.1, E6 6” 2K,
Flashforge: Foto 9.25, Foto 8.9, Foto 6.0
Kelant: C60, Flare
Kudo: Bean, Bean Plus
Longer: Orange 10, Orange 30, Orange 4K
Phrozen: Sonic Mini, Mini 4K, Mini 8K, Mighty, Mighty 8K
Voxelab: Proxima 6.0 2K, Proxima 6.0 4K, Proxima 8.9 4k, Polaris 2K
Uniz: IBEE
Send us an email if you can confirm any other machine fits not listed and we would be happy to offer you a coupon or gift: technical@whambamsystems.com
For printable HotBox accessories, visit our HotBox support page: whambamsystems.com/hotbox-support
All of our HotBox lines are made of high-grade Nylon 600D fabric with fire-resistant coating and lined with a metallic heat-deflecting internal liner that sandwiches around a strong, lightweight honeycomb insulating structure. It has a temperature gauge right on the front panel so you can monitor the internal temperature. You can allow the heat of the machine and the catalytic reaction of curing resin to maintain temperatures or add a small heater.
Features of the Resin HotBox enclosure include:
-Lightweight semi-rigid construction
-Excellent insulating properties
-Folds up flat, is easy to store and transport
-Front USB outlet and extension cable
-Cable passage for power or other cables
-Full view front window covered with an anti-UV film to allow viewing the print
-Built-in thermometer (two LR44 batteries not included)
-Passage with cover for user-added fume extraction and air filtering
-A set of loops to hold a LED light bar
-Built-in top handle to lift the enclosure when needed
Where to find us online:
WhamBamSystems.com
facebook.com/WhamBamSystems
twitter.com/whambamsystems
instagram.com/whambamsystems
linkedin.com/company/35445851
tiktok.com/@whambamsystems
reddit.com/user/WhamBamSystems
The Resin HotBox was created to get consistent results and fewer failures with a temperature-controlled ambient resin printer enclosure. Almost every resin prints better at specific temperature ranges, especially the higher-performance and exotic resins. The Resin HotBox enclosure also helps to trap fumes and has a built-in port to add fume extraction.
00:04 Introduction
00:18 Why Do You Need An Enclosure For A Resin Printer?
01:27 Features
03:25 Instant Access to Machine
04:09 Size and Machine Fits
05:47 LED USB BAR for Resin
06:23 Unboxing and Set Up
9:54 Conclusion
The Resin HotBox is 330mm wide x 330mm deep x 580mm tall and fits the following printers:
AnyCubic: Photon, Ultra, S, SQ, Mono, Mono SE, X, 4K, X 6K, M3, D2 DLP
Creality: Halot, Halot One, Halot One Pro, Halot One Plus, Halot Lite, Halot Sky, LD002 H, LD002 R, LD 006
Elegoo: Saturn, Saturn 2 8k, Saturn 8K, Mars, Mars Pro V2, Mars C, Mars 3, Mars 3 Pro, Mars 3 Ultra 4k
EPAX: E10, E10 8K 10.1, E10 4K, E10 4K 8.9 , E10 5K 10.1, E6 6” 2K,
Flashforge: Foto 9.25, Foto 8.9, Foto 6.0
Kelant: C60, Flare
Kudo: Bean, Bean Plus
Longer: Orange 10, Orange 30, Orange 4K
Phrozen: Sonic Mini, Mini 4K, Mini 8K, Mighty, Mighty 8K
Voxelab: Proxima 6.0 2K, Proxima 6.0 4K, Proxima 8.9 4k, Polaris 2K
Uniz: IBEE
Send us an email if you can confirm any other machine fits not listed and we would be happy to offer you a coupon or gift: technical@whambamsystems.com
For printable HotBox accessories, visit our HotBox support page: whambamsystems.com/hotbox-support
All of our HotBox lines are made of high-grade Nylon 600D fabric with fire-resistant coating and lined with a metallic heat-deflecting internal liner that sandwiches around a strong, lightweight honeycomb insulating structure. It has a temperature gauge right on the front panel so you can monitor the internal temperature. You can allow the heat of the machine and the catalytic reaction of curing resin to maintain temperatures or add a small heater.
Features of the Resin HotBox enclosure include:
-Lightweight semi-rigid construction
-Excellent insulating properties
-Folds up flat, is easy to store and transport
-Front USB outlet and extension cable
-Cable passage for power or other cables
-Full view front window covered with an anti-UV film to allow viewing the print
-Built-in thermometer (two LR44 batteries not included)
-Passage with cover for user-added fume extraction and air filtering
-A set of loops to hold a LED light bar
-Built-in top handle to lift the enclosure when needed
Where to find us online:
WhamBamSystems.com
facebook.com/WhamBamSystems
twitter.com/whambamsystems
instagram.com/whambamsystems
linkedin.com/company/35445851
tiktok.com/@whambamsystems
reddit.com/user/WhamBamSystems
