Uploaded May 2025 | Updated November 2026, 16 hours ago
Hello!
Welcome to this first detailed overview of the Seashell.
00:00:00 Instruōduction
00:01:41 Getting Started (init patch setup)
00:07:53 DIFFUSE
00:14:35 Software/DAW integration
00:25:44 Filter Source Routing
00:29:26 GATE to VCA
00:32:54 Filter Controls
00:41:09 Oscillator 2 Low Frequency Mode (LF)
00:44:06 F.M. Routing
00:47:41 Analogue FM
00:53:42 Complex Oscillator (Circular) FM
00:57:00 WAVEFOLD
01:12:11 Pulse Width Modulation
01:19:15 Envelope Modes
01:26:33 Pitch Control Routing (1V/OCT)
01:30:04 TRANSPOSE
01:38:12 Oscillator Sync
01:50:40 EXTEND
02:12:52 MIDI Mapping
Hello!
Welcome to this first detailed overview of the Seashell.
00:00:00 Instruōduction
00:01:41 Getting Started (init patch setup)
00:07:53 DIFFUSE
00:14:35 Software/DAW integration
00:25:44 Filter Source Routing
00:29:26 GATE to VCA
00:32:54 Filter Controls
00:41:09 Oscillator 2 Low Frequency Mode (LF)
00:44:06 F.M. Routing
00:47:41 Analogue FM
00:53:42 Complex Oscillator (Circular) FM
00:57:00 WAVEFOLD
01:12:11 Pulse Width Modulation
01:19:15 Envelope Modes
01:26:33 Pitch Control Routing (1V/OCT)
01:30:04 TRANSPOSE
01:38:12 Oscillator Sync
01:50:40 EXTEND
02:12:52 MIDI Mapping

![Instruō - tràigh Design | EPISODE 4
Related links:
• Project overview | https://youtu.be/Tf8rzK1F0OI
• Original Instruō - tràigh [Signature Edition] overview | https://youtu.be/AfdHsUG6XjQ
• DivKid Winston tràigh feature | https://youtu.be/BCwvgQQUbi4?si
*tràigh design | Synth design series*
• Episode 1 - https://youtu.be/4iwu9G6zji4
• Episode 2 - https://youtu.be/UzohwRfge3A
• Episode 3 - https://youtu.be/tI0cQyLMTsg
• Episode 4 - https://youtu.be/xh6RkCffNgY
• Episode 5 - https://youtu.be/-XHrDBgti_k
*Signal Sounds Glasgow*
https://www.signalsounds.com/
~~~
Hello!
Welcome to episode 4 of this module design series.
This episode is the following day from episodes 1/2/3.
Schematic is done. In this video I work through placement of the SMT components problem solving through orientation of opamps and optimal placement for most efficient signal routing.
I then work through the routing of the full board.
There are big chunks where Im just working, so I shorted them to timelapse.
I return to real time whenever I talk about what Im doing.
I think this session was actually ~6 hours, so I condensed it down to something a bit more manageable in length!
My apologies for the change in audio in the second half.
I took a coffee break and forgot to clip the lav mic back onto my tshirt.
So the audio is less close mic quality, but I spent a good bit of time in RX cleaning things up.
Thanks for watching!
00:00:00 Instruōduction
00:01:02 Episode 4 Instruō - tràigh Design | EPISODE 4](https://i.ytimg.com/vi/xh6RkCffNgY/mqdefault.jpg)








