Uploaded June 2025 | Updated November 2026, 1 day ago
Impedance Matching playlist.
youtube.com/watch?v=VYor6jGA1-4&list=PLFxhgwM1F4yxNelYq8IuV-qancL8186LV
For access to this presentation materials, membership is required: I need the Material PPT
Sent me an email to Technologies.Discussion@gmail.com
If you need the whole playlist material, send me email and we discuss.
Give me some time to response. Thanks.
Impedance Matching #3. How to Design L Section Network with Lumped Elements Inductor & Capacitor.
Designing an L-matching network using a lumped inductor and capacitor involves transforming a given load impedance (ZL) to a desired input impedance (Zin) at a specific frequency. The L-section matching network is one of the simplest matching topologies and can be configured in two possible arrangements:
Series-L, Shunt-C
Shunt-L, Series-C
The choice depends on whether the load impedance is higher or lower than the source impedance (usually RS = 50Ω)
Step-by-Step Design Procedure
Assume we want to match a load impedance ZL=RL+jXL to a purely resistive source ZS=RS at frequency f.
1. Normalize the Impedances
First, normalize the load impedance with respect to RS
Determine the Matching Topology
(load resistance is larger than source resistance) → Use Shunt-C, Series-L
(load resistance is smaller than source resistance) → Use Shunt-L, Series-C
Impedance Matching playlist.
youtube.com/watch?v=VYor6jGA1-4&list=PLFxhgwM1F4yxNelYq8IuV-qancL8186LV
For access to this presentation materials, membership is required: I need the Material PPT
Sent me an email to Technologies.Discussion@gmail.com
If you need the whole playlist material, send me email and we discuss.
Give me some time to response. Thanks.
Impedance Matching #3. How to Design L Section Network with Lumped Elements Inductor & Capacitor.
Designing an L-matching network using a lumped inductor and capacitor involves transforming a given load impedance (ZL) to a desired input impedance (Zin) at a specific frequency. The L-section matching network is one of the simplest matching topologies and can be configured in two possible arrangements:
Series-L, Shunt-C
Shunt-L, Series-C
The choice depends on whether the load impedance is higher or lower than the source impedance (usually RS = 50Ω)
Step-by-Step Design Procedure
Assume we want to match a load impedance ZL=RL+jXL to a purely resistive source ZS=RS at frequency f.
1. Normalize the Impedances
First, normalize the load impedance with respect to RS
Determine the Matching Topology
(load resistance is larger than source resistance) → Use Shunt-C, Series-L
(load resistance is smaller than source resistance) → Use Shunt-L, Series-C









![Electrical Principles #4. Electrical Power Vs Energy Explained: Formulas, Units & Practical Examples
Electrical Principles playlist:
https://www.youtube.com/watch?v=k6thiyNzjpQ&list=PLEvyI-PjnnzI
Electrical Power (P)
Electrical power is the rate at which electrical energy is used or transferred.
Electrical Energy (E)
Electrical energy is the total amount of electrical energy consumed or transferred over a period of time.
Electrical Power, (P) in a circuit is the rate at which electrical energy is absorbed or produced within a circuit. A source of energy such as a voltage will produce or deliver power while the connected load absorbs it.
Light bulbs & heaters for example, absorb electrical power & convert it into either heat or light or both. The higher their value or rating in watts the more electrical power they are likely to consume.
The quantity symbol for power is “P”. It is the product of voltage multiplied by the current with the standard electrical units of measurement being the Watt (W). Prefixes are used to denote the various multiples or sub-multiples of a watt. For example: milliwatts (mW = 10-3 Watts) or kilowatts (kW = 103 Watts).
Calculating Electric Power Using Ohms Law
[ P = V x I ]⟹P (watts) = V (volts) x I (amps)
Also:
[ P = V2 ÷ R ]⟹P (watts) = V2 (volts) ÷ R (Ω)
Also:
[ P = I2 x R ]⟹P (watts) = I2 (amps) x R (Ω)
Electrical Energy
This is the property of a system that enables it to do work. Whenever work is done, energy is transferred from one system to another. The most common form into which energy is transformed is heat (electric current is to produce heat) (Electric kettle).
J. P. Joule carried out an investigation into this effect. He concluded that the amount of heat produced was proportional to the square of the current flowing and the time for which it flowed. Once again, a constant of proportionality is required, and the resistance of the circuit is used. Thus, the heat produced (or energy dissipated) is given by the equation:
The Commercial Unit of Energy (kWh)
Although the joule is the SI unit of energy, it is too small a unit for some practical uses, for example, when large amounts of energy are consumed over long periods of time.
The electricity meter in your home actually measures energy consumption. So, if a 3 kW heater is in use for 12 hours, the amount of energy used would be 129.6 MJ. In order to record this, the meter would require at least ten dials to indicate this very large number. In addition, many of them would have to rotate at an impractical rate.
Hence, the commercial unit of energy is the kilowatt-hour (kWh). Kilowatt-hours are the “units” that appear on electricity bills. The number of units consumed can be calculated by multiplying the power (in kW) by the time interval (in hours).
For the heater mentioned above, the number of “units” consumed would be 36 kWh. It should be apparent from this that fewer dials are required to record this particular figure, and their speed of rotation is perfectly acceptable. Electrical Principles #4. Electrical Power Vs Energy Explained: Formulas, Units & Practical Examples](https://i.ytimg.com/vi/gtxVR6NbkgA/mqdefault.jpg)
