Uploaded November 2018 | Updated September 2026, 2 weeks ago
ImmersionRC may have confirmed that RapidFIRE modules of Batch #2 have mainly improved in terms of compatibility to camera/VTx/OSD setups, but what is better than finding it out on your own during a sunny day at a bando with friends, two modules, plenty of antennas and a huge box with FPV monitors and a camera inside?
TLDR: Modules from batch #1 and batch #2 seem to have identical performance. Flash the latest firmware, stick a rubber cube between the SMA connectors and consider your batch #1 module equal to a batch #2. There is no need to upgrade or mod your batch #1 module, unless you are experiencing compatibility issues.
If you have already seen my previous FPV goggle module shootouts, rest assured that the same attention to detail has been put into this round of comparisons as well. Everything used is identical between the modules, same types and lengths of wires, same plugs, high quality RCA A/V connectors etc. If you haven't, definitely take a look at the relevant playlist: goo.gl/dWRzwz
The "test quad" was using a TBS Unify Pro 5G8 V3 VTx at 200mW on F4 5800MHz with an AXII antenna and a Runcam Swift 2 camera, through a Revolt OSD F/C.
Huge thanks to Kokobloko for all the flying and support. If you liked what you saw, check out his channel here: goo.gl/7kNpmL
This is ImmersionRC RapidFIRE Batch #1 vs RapidFIRE Batch #2: Side-by-Side comparison of the FPV video feed - Let's go!
____________________
π If you like my content and want to support the channel, you can tip my 'piggy bank' via PAYPAL, here: goo.gl/gqrYuh
------------------------------
π You can also use the following affiliate links, or bookmark the store links at the end of the description - I get a small kickback from some of these stores if you decide to buy something and it costs nothing extra to you.
π Subscribe for more unique content, here: goo.gl/6HNc7H
Thank you in advance!
π FPV Monitors used (4 +1 spare):
goo.gl/6nskBJ (Banggood)
π ImmersionRC RapidFIRE FPV goggle module:
goo.gl/qXdcFB (Banggood)
goo.gl/udKmCi (HobbyKing)
goo.gl/1hJzSp (Ebay)
goo.gl/dmDvyQ (GetFPV)
goo.gl/dV7rQt (PiroFlipRC)
goo.gl/LqPgB1 (QuadCopters)
goo.gl/wm1QQ2 (FliteTest)
goo.gl/g5KrSX (MRP)
π TrueRC Long AXII omni antenna:
goo.gl/tDsGhZ (TrueRC)
π TrueRC XAir crosshair antenna:
goo.gl/svfV5k (TrueRC)
ImmersionRC Drivers: goo.gl/RcExf1
RapidFIRE Updater utility: goo.gl/rjxtv9
RapidFIRE product page: goo.gl/CpLKrJ
RapidFIRE product manual: goo.gl/wv74Dt
ImmersionRC Hub group on Facebook: goo.gl/ovn6wm
Note: If you pause the video and see ghosting around objects / buildings, it is probably because of the FPV monitors and my DSLR combination. It is not related to the RapidFIRE module or the camera/VTx used on the quad.
====================
π π π HOW TO SUPPORT THE [MuteFPV] CHANNEL:
----------------------------
You can tip my 'piggy bank' via PAYPAL, here: goo.gl/gqrYuh
You can also click or save these convenient BOOKMARKS in your browser and use them to visit the websites, before purchasing new goodies:
BANGGOOD (opens the RC Toys & Hobbies category, showing the Newest products): goo.gl/R4TceG
AMAZON (paid link): mutefpv.com/amazon
GEARBEST (opens the Toys & Hobbies R/C category, showing the Newest products): goo.gl/wwTJwt
EBAY (the shortlink has to be bookmarked): goo.gl/gFRdy5
FPVMODEL (newest products): goo.gl/zmPxbf
HORUSRC (main page): goo.gl/n2fJDq
A huge THANK YOU in advance for your support!
====================
-------------------------------
This video features the song "Where civilization once lay (extended)" from SWITCH Trailer Music, available under a Creative Commons License
Song link: youtube.com/watch?v=H_yXjfFE99o
CC-by license: creativecommons.org/licenses/by/3.0
-------------------------------
#muteFPV
#IRCRapidFIRE
#RapidFIRE
ImmersionRC may have confirmed that RapidFIRE modules of Batch #2 have mainly improved in terms of compatibility to camera/VTx/OSD setups, but what is better than finding it out on your own during a sunny day at a bando with friends, two modules, plenty of antennas and a huge box with FPV monitors and a camera inside?
TLDR: Modules from batch #1 and batch #2 seem to have identical performance. Flash the latest firmware, stick a rubber cube between the SMA connectors and consider your batch #1 module equal to a batch #2. There is no need to upgrade or mod your batch #1 module, unless you are experiencing compatibility issues.
If you have already seen my previous FPV goggle module shootouts, rest assured that the same attention to detail has been put into this round of comparisons as well. Everything used is identical between the modules, same types and lengths of wires, same plugs, high quality RCA A/V connectors etc. If you haven't, definitely take a look at the relevant playlist: goo.gl/dWRzwz
The "test quad" was using a TBS Unify Pro 5G8 V3 VTx at 200mW on F4 5800MHz with an AXII antenna and a Runcam Swift 2 camera, through a Revolt OSD F/C.
Huge thanks to Kokobloko for all the flying and support. If you liked what you saw, check out his channel here: goo.gl/7kNpmL
This is ImmersionRC RapidFIRE Batch #1 vs RapidFIRE Batch #2: Side-by-Side comparison of the FPV video feed - Let's go!
____________________
π If you like my content and want to support the channel, you can tip my 'piggy bank' via PAYPAL, here: goo.gl/gqrYuh
------------------------------
π You can also use the following affiliate links, or bookmark the store links at the end of the description - I get a small kickback from some of these stores if you decide to buy something and it costs nothing extra to you.
π Subscribe for more unique content, here: goo.gl/6HNc7H
Thank you in advance!
π FPV Monitors used (4 +1 spare):
goo.gl/6nskBJ (Banggood)
π ImmersionRC RapidFIRE FPV goggle module:
goo.gl/qXdcFB (Banggood)
goo.gl/udKmCi (HobbyKing)
goo.gl/1hJzSp (Ebay)
goo.gl/dmDvyQ (GetFPV)
goo.gl/dV7rQt (PiroFlipRC)
goo.gl/LqPgB1 (QuadCopters)
goo.gl/wm1QQ2 (FliteTest)
goo.gl/g5KrSX (MRP)
π TrueRC Long AXII omni antenna:
goo.gl/tDsGhZ (TrueRC)
π TrueRC XAir crosshair antenna:
goo.gl/svfV5k (TrueRC)
ImmersionRC Drivers: goo.gl/RcExf1
RapidFIRE Updater utility: goo.gl/rjxtv9
RapidFIRE product page: goo.gl/CpLKrJ
RapidFIRE product manual: goo.gl/wv74Dt
ImmersionRC Hub group on Facebook: goo.gl/ovn6wm
Note: If you pause the video and see ghosting around objects / buildings, it is probably because of the FPV monitors and my DSLR combination. It is not related to the RapidFIRE module or the camera/VTx used on the quad.
====================
π π π HOW TO SUPPORT THE [MuteFPV] CHANNEL:
----------------------------
You can tip my 'piggy bank' via PAYPAL, here: goo.gl/gqrYuh
You can also click or save these convenient BOOKMARKS in your browser and use them to visit the websites, before purchasing new goodies:
BANGGOOD (opens the RC Toys & Hobbies category, showing the Newest products): goo.gl/R4TceG
AMAZON (paid link): mutefpv.com/amazon
GEARBEST (opens the Toys & Hobbies R/C category, showing the Newest products): goo.gl/wwTJwt
EBAY (the shortlink has to be bookmarked): goo.gl/gFRdy5
FPVMODEL (newest products): goo.gl/zmPxbf
HORUSRC (main page): goo.gl/n2fJDq
A huge THANK YOU in advance for your support!
====================
-------------------------------
This video features the song "Where civilization once lay (extended)" from SWITCH Trailer Music, available under a Creative Commons License
Song link: youtube.com/watch?v=H_yXjfFE99o
CC-by license: creativecommons.org/licenses/by/3.0
-------------------------------
#muteFPV
#IRCRapidFIRE
#RapidFIRE
![SpeedyBee Bluetooth UART Adapter (SBBUA) overview & setup - BEST FOR LESS
If you are running Betaflight and have been carrying a laptop or Windows tablet with you in order to tune or set up your quad on the field, you will be very happy to see this UART-Bluetooth adapter from SpeedyBee!
It is a small, light and easy to install board that allows you full access of all your settings, including CLI, from your phone or tablet. The GUI is very clean and easy to use, everything is nicely labeled and the setup is very straight-forward. Only enabling the BLE Switch may require that you look into your F/C manual, just to be sure about the pin assignment.
Even if you dont want to get one right now, if I were you and had an extra UART on the F/C, I would enable it just as a backup - this way if you ever damage the USB connector of your F/C, you can get a SpeedyBee BUA board, connect it to that UART and continue to use your F/C ;)
This is BEST FOR LESS: SpeedyBee Bluetooth UART Adapter (SBBUA) overview & setup - Lets go!
π If you like my content and want to support the channel, you can tip my piggy bank via PAYPAL, here: https://goo.gl/gqrYuh
π π You can also use the following affiliate links, or bookmark the store links at the end of the description - I get a small kickback from some of these stores if you decide to buy something and it costs nothing extra to you.
π π π Subscribe for more unique content, here: https://goo.gl/6HNc7H
Thank you in advance!
π π SpeedyBee BUA
https://goo.gl/FvhSJ3 (Banggood)
https://goo.gl/Gmpmxs (Ebay)
https://goo.gl/z2vTm9 (SpeedyBee)
π π Product manual: https://goo.gl/yBWCcE (Runcam)
The stack I used consists of the following:
π Matek F405 STD
https://goo.gl/y2rmKZ (HobbyKing)
https://goo.gl/3cjoNa (Banggood)
https://goo.gl/XTXHN1 (Ebay)
https://goo.gl/Hd8vjk (Gearbest)
π Matek FCHUB-VTX
https://goo.gl/XBy8xo (Banggood)
https://goo.gl/1Sh5XW (Ebay)
https://goo.gl/3hJGSu (Gearbest)
https://goo.gl/hHNEHv (HobbyKing)
π FrSky XM+
https://goo.gl/QfAEcK (Banggood)
https://goo.gl/96Jpmn (Ebay)
https://goo.gl/tT8U8p (Gearbest)
π π If you like my Taranis X9D+, check the Taranis mods playlist for mods and upgrades:
https://www.youtube.com/playlist?list=PLT1bw0pJRpO0jCI6L_p_5_ON4arVoZJt8
π π π HOW TO SUPPORT THE [MuteFPV] CHANNEL:
You can tip my piggy bank via PAYPAL, here: https://goo.gl/gqrYuh
You can also click or save these convenient BOOKMARKS in your browser and use them to visit the websites, before purchasing new goodies:
BANGGOOD (opens the RC Toys & Hobbies category, showing the Newest products): https://goo.gl/R4TceG
GEARBEST (opens the Toys & Hobbies R/C category, showing the Newest products): https://goo.gl/wwTJwt
EBAY (the shortlink has to be bookmarked): https://goo.gl/gFRdy5
FPVMODEL (newest products): https://goo.gl/zmPxbf
HORUSRC (main page): https://goo.gl/n2fJDq
A huge THANK YOU in advance for your support!
This video features the song Deep Thoughts by DeeTunez, available under a Creative Commons License
Song link: https://soundcloud.com/deetunez/deep-thoughts
Artist link: https://soundcloud.com/deetunez
CC-by license: https://creativecommons.org/licenses/by/3.0/
#muteFPV SpeedyBee Bluetooth UART Adapter (SBBUA) overview & setup - BEST FOR LESS](https://i.ytimg.com/vi/ln1gkXAupQE/mqdefault.jpg)








![Doorway air gates, magnets and new LED lights for illuminated gates + Giveaway! - QUICK GUIDE
It is that time of the year again, so here is your Christmassy dose of air gates for your micro quads and tiny whoops!
This is the simplest and most versatile way I have found to mount air gates in the doorways of my home, quickly and on the cheap.
I threw in some other alternatives as well, including some useful parts which you can 3D print.
As for the LED lights (giveaway details below), aside from the short battery life, these laces are awesome and very bright! Probably I will buy the shorter 120cm versions next, which I expect will have significantly longer battery life.
Dont forget to leave your comment in order to participate!
I wish you all a Merry Christmas and a Happy New Year, full of happiness, strong RSSI and many hours in the air ;)
If you havent already, check my dirt cheap hula hoop illuminated gates here: https://youtu.be/ElL0hSiFG44
For an illuminated collapsible tunnel, an easy U-turn pole and a large hoop which you can hang anywhere, as simple and as cheap as possible, check last years Xmas video: https://youtu.be/POfsvbSN5rM
This is QUICK GUIDE: Doorway air gates, magnets and new LED lights for illuminated gates + Giveaway! - Lets go!
π If you like my content and want to support the channel, you can tip my piggy bank via PAYPAL, here: https://goo.gl/gqrYuh
π You can also use the following affiliate links, or bookmark the store links at the end of the description - I get a small kickback from some of these stores if you decide to buy something and it costs nothing extra to you.
π Subscribe for more unique content, here: https://goo.gl/6HNc7H
Thank you in advance!
π LDARC air gates (slim)
https://goo.gl/D71gU8 (Banggood)
https://goo.gl/uosa9t (Ebay)
https://goo.gl/Sn1TUd (AliExpress)
π BetaFPV air gates (set of 4)
https://goo.gl/MwZMi6 (BetaFPV)
https://goo.gl/QjZQGK (Ebay)
π LED light strips (laces)
https://goo.gl/QWFsS9 (BetaFPV)
π Adjustable rods (various length ranges)
https://goo.gl/h9zczP (Ebay)
https://goo.gl/Bs37Ky (Banggood)
https://goo.gl/Wfr4KW (Gearbest)
https://goo.gl/zddNLk (AliExpress)
π Strong magnets
https://goo.gl/BaBnbm (Banggood)
https://goo.gl/s4NtqZ (Gearbest)
https://goo.gl/17txQB (Ebay)
https://goo.gl/GkbmGT (AliExpress)
π 3D printed parts
Tiny whoop gate adapters: https://goo.gl/JW5Tfx (Facebook)
SeekNDs magnet adapter: https://goo.gl/ZgK6tJ (Thingiverse)
LunchBox gate clamp stands: https://goo.gl/UMHoj4 (Thingiverse)
π These parts were printed on the Ender 3 (3D-printing content coming soon):
https://goo.gl/y6k4uE (Banggood)
https://goo.gl/Rk4YQH (Gearbest)
π GIVEAWAY WINNER: Myungsik Kim π
Video proof: https://youtu.be/I5ZcZugLrPA
GIVEAWAY DETAILS:
The Giveaway is for three (3) BetaFPV LED light strips, which will be sent to the winner directly from BetaFPV.
In order to participate, leave any comment you like in the comments section of this video.
Check the LED light strips here: https://betafpv.com/products/betafpv-led-strip-1-pc
You dont have to be a subscriber but if you enjoy my content, why not? ;)
The winner will be drawn the first few days after New Years Eve and will be announced in this video, either in writing or with an unlisted video showing the draw process, as I usually do.
Basic giveaway rules:
1. Entries that do not comply with YouTubes community guidelines (https://www.youtube.com/yt/about/policies/#community-guidelines) will be invalid.
2. YouTube is not a sponsor of this contest. By participating, you must release YouTube from any and all liability related to this contest.
3. Any personal information that is collected for this contest will be used for the sole purpose of selecting the winner and delivering the prizes.
4. The winner will be selected randomly, using a Youtube comment picker, a random number generator or similar process.
Huge thanks to BetaFPV for supporting this Giveaway and GOOD LUCK to everyone!
HOW TO SUPPORT THE [MuteFPV] CHANNEL:
You can tip my piggy bank via PAYPAL, here: https://goo.gl/gqrYuh
You can also click or save these convenient BOOKMARKS in your browser and use them to visit the websites, before purchasing new goodies:
BANGGOOD: https://goo.gl/R4TceG
AMAZON (paid link): http://mutefpv.com/amazon
GEARBEST: https://goo.gl/wwTJwt
EBAY (the shortlink has to be bookmarked): https://goo.gl/gFRdy5
FPVMODEL: https://goo.gl/zmPxbf
HORUSRC: https://goo.gl/n2fJDq
A huge THANK YOU in advance for your support!
This video features the song Home Alone (jO.z Brooklyn Instrumental Edit) by Aposto, available under a Creative Commons License
Song link: https://soundcloud.com/joaposto/home-alone-awr-brooklyn-edit
Artist link: https://soundcloud.com/joaposto
CC-by license: https://creativecommons.org/licenses/by/3.0/
#muteFPV
#TinyWhoopGates
#DIYgates Doorway air gates, magnets and new LED lights for illuminated gates + Giveaway! - QUICK GUIDE](https://i.ytimg.com/vi/pEOJsC6TAMc/mqdefault.jpg)
